• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.5 no.1
• /
• pp.47-55
• /
• 1999

Applications of chitosan are related to molecular weight and degree of deacetylation(DOD) of chitosan completely. The molecular weight and DOD were greatly affected by the concentration of solution time and temperature. The degree of demineralization was not significantly different at $50^{\circ}C\;and\;70^{\circ}C$ after 30 minutes. Deproteinization decreased as process time increased. The nitrogen content was reached to 6.92% after 90 minute at $80^{\circ}C$, which is similar to theoretical nitrogen content of chitin. The DOD was 82.84% after 2 hours reaction and increased as the reaction time increased in the process. Viscosity and molecular weight are increased as recycling number of concentrated NaOH solution increased. Chemical, biological and physical properties of chitosan depend on the DOD and molecular size of the molecule. Tensile strength of the films from acetic acid solutions was between $28.9{\sim}33.6$ MPa and was generally higher than that of the films from lactic acid. Elongation of the films from lactic acid was between $97.0{\sim}109.7%$ and was generally higher than that of the films from the acetic acid. Water vapor permeability of the films prepared from lcetic acid solutions was between $1.9{\sim}2.3ng{\cdot}m/m^2{\cdot}s{\cdot}Pa$ and was generally higher than that of the films from the acetic acid.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.1 no.1
• /
• pp.17-25
• /
• 2013

Thermal storage technology used for indoor heating and cooling to maintain a constant temperature for a long period of time has an advantage of raising energy use efficiency. This, the phase changing material, which utilizes heat storage properties of the substances, capsulizes substances that melt at a constant temperature. This is applied to construction materials to block or save energy due to heat storage and heat protection during the process in which substances melt or freeze according to the indoor or outdoor temperature. The micro-encapsulation method is used to create thermal storage from phase changing material. This method can be broadly classified in 3 ways: chemical method, physical and chemical method and physical and mechanical method. In the physical and chemical method, a wet process using the micro-encapsulation process utilized. This process emulsifies the core material in a solvent then coats the monomer polymer on the wall of the emulsion to harden it. In this process, a surfactant is utilized to enhance the performance of the emulsion of the core material and the coating of the wall monomer. The performance of the micro-encapsulation, especially the coating thickness of the wall material and the uniformity of the coating, is largely dependent on the characteristics of the surfactant. This research compares the performance of the micro-capsules and heat storage for product according to molecular mass and concentration of the surfactant, SSMA (sulfonated styrene-maleic anhydride), when it comes to micro-encapsulation through interfacial polymerization, in which Dodecan-1 is transformed to melamin resin, a heat storage material using phase changing properties. In addition, the thickness of the micro-encapsulation wall material and residual melamine were reduced by adjusting the concentration of melamin resin microcapsules.

• Korean Journal of Environmental Agriculture
• /
• v.36 no.1
• /
• pp.43-49
• /
• 2017

BACKGROUND: Greenhouse crops are one of agricultural products consumed largely in Korea. Cucumber is a typical example as main vegetables of greenhouse crops. Thus, pesticide residue analysis is an important requirement to guarantee pesticide safety of cucumber. This work was aim to investigate the residues of penthiopyrad and pyriofenone in cucumber after harvest. METHODS AND RESULTS: Cucumber was subjected to treat with penthiopyrad and pyriofenone at a level of recommended dose 0, 1, 2, 3, 5, 7 and 10 days before harvest under greenhouse conditions. The samples were extracted with organic solvent by using a homogenizer and purified on solid phase cartridge column followed by LC-MS/MS analysis. The recovery levels of penthiopyrad and pyriofenoneranged from approximately 81 to 93% with the method limit of 0.005 mg/kg and coefficient of variation less than 10%. Penthiopyrad and pyriofenone were detected at a level less than maximum residue limit in cucumber at 10 days before. The half-lives of penthiopyrad and pyriofenone were determined to 2.4 ~ 2.6 days. CONCLUSION: Penthiopyrad and pyriofenone are suggested to use in cucumber 10 days before harvest to reach their levels less than maximum residue limit.

• Food Science and Preservation
• /
• v.13 no.6
• /
• pp.720-725
• /
• 2006

This study was conducted to investigate extracting solution effect on the chemical compositions in different parts of Korean mountain Ginseng. Water, 80% EtOH and 80% MeOH are used as extraction solutions, and extracting conditions were 2 hr at $85^{\circ}C$ in water bath. The Brix(%) of the extract were ranged from $0.42{\sim}22.58%$, 80% EtOH extract for leaf is the highest level as 22.58%. The pH ranges of the extracts were $4.43{\sim}7.41$ and brown color of the extract was the highest with 1.803 in 80% EtOH extract for leaf, respectively. In case of hunter's color value of the extract, L value is the highest with 24.35 in 80% EtOH extract of seed, a and b value were the highest with 0.41 in 100% water extract of leaf and 3.69 in 80% MeOH extract of stem. Sucrose is the major free sugar of the extinct it highest content with 3673 mg% in 80% MeOH extract of mot and fructose is the highest with 1897 mg% in 80% MeOH extract of leaf, Major organic acids are identified as malic, tartaric and citric acid, and total organic acid content is the highest with 5,254 mg% in 80% MeOH extract of leaf and 1,527 mg% in 80% EtOH extract of leaf, The extracted major minerals ate P and K, P content highest with 15,563 ppm in 100% water extract of stem, K is 4,952 ppm in 80% MeOH extract of leaf, and Ca is the highest with 3,052 ppm in 1011% water extract of leaf. These results suggest that extracting solvent (80% MeOH) is concerned with the extract preparation of Korea Mountain Ginseng.

• Korean Journal of Environmental Agriculture
• /
• v.36 no.1
• /
• pp.57-62
• /
• 2017

BACKGROUND: Pesticide residue analysis is essentially required for safety evaluation of agricultural products. Bistrifluron and chlorantraniliprole have been currently considered as potentials to deeply evaluate their residues in agricultural products because they are frequently found in strawberry. This work was performed to investigate the residual patterns of bistrifluron and chlorantraniliprole in strawberry after harvest. METHODS AND RESULTS: Strawberry was treated with bistrifluron and chlorantraniliprole 0, 1, 2, 3, 5, 7 and 10 days before harvest under greenhouse conditions. The strawberry samples were subjected to solvent and solid phase extractions followed by LC-MS/MS analysis. There covery percentages of bistrifluron and chlorantraniliprole for tified in the control samples ranged from approximately 82 to 103% with the method limit of 0.005 mg/kg. The concentrations of bistrifluron and chlorantraniliprole in strawberry samples decreased significantly in 10 days after treatment, giving the safety levels of 0.04 to 0.06 mg/kg at 10 days after application, as considered maximum residue limit. The half-lives of bistrifluron and chlorantraniliprole based on first order kinetics were determined to 6.3 days and 6.4 days, respectively. CONCLUSION: Bistrifluron and chlorantraniliprole are suggested to use in strawberry 10 days before harvest to reach residual safety levels.

• Applied Chemistry for Engineering
• /
• v.7 no.5
• /
• pp.877-887
• /
• 1996

The ideal membranes for membrane-covered oxygen probes system should be selectively permeable for oxygen and chemically inert, and have good mechanical strength. Polysulfone(PSf) was selected to develop the membrane for membrane-covered oxygen electrodes system. PSf membranes have properties such as good reproducibility, good mechanical strength, chemical inertness, and high heat resistance. PSf membranes were cast from polymer solution on the glass plate at constant temperature, and casting solvents used were tetrahydrofuran(THF), methylene chloride, and N-methyl-2-pyrrolidone(NMP). Tricresyl phosphate(TCP) as plasicizer was added to PSf to increase the softness of membrane. The permeation characteristics were observed for pure oxygen and nitrogen through pure PSf membranes by variable volume method and membrane-covered electrode system. The permeability coefficients of oxygen and nitrogen measured by variable volume method were slightly decreased with increasing of upstream pressure. The permeation properties of PSf membrane using methylene choride as casting solvent were not affected by the PSf amount of polymer solution. The permeability coefficients of oxygen and nitrogen for PSf membrane containing TCP were very slightly lower than those for pure PSf membrane, but ideal separation factors were slightly higher. The flexibility of PSf membrane containing 2wt% TCP was better than that of pure PSf membrane. It was expected that this increase in flexibility would solve the difficulty of fixing the membrane to the cathode. The membrane-covered oxygen probes system was composed of anode, cathode and electrolyte. The type of the anode was Ag/AgCl half-cell, that of cathode was Ag, and the electrolyte was 4N KCl solution. The result of sampled current voltametry for PSf membrane showed the plateu region at -0.3V~-1.0V. The correlation coefficient of oxygen partial pressure versus current for PSf membrane was relatively high, 0.99949. It was concluded that PSf membrane was the good candidate for the membrane-covered oxygen probes system.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.5-5
• /
• 2011

The research and development of hybrid electric vehicle (HEV), plug-in hybrid electric vehicle (PHEV) and electric vehicle (EV) are intensified due to the energy crisis and environmental concerns. In order to meet the challenging requirements of powering HEV, PHEV and EV, the current lithium battery technology needs to be significantly improved in terms of the cost, safety, power and energy density, as well as the calendar and cycle life. One new technology being developed is the utilization of composite cathode by mixing two different types of insertion compounds [e.g., spinel $LiMn_2O_4$ and layered $LiMO_2$ (M=Ni, Co, and Mn)]. Recently, some studies on mixing two different types of cathode materials to make a composite cathode have been reported, which were aimed at reducing cost and improving self-discharge. Numata et al. reported that when stored in a sealed can together with electrolyte at $80^{\circ}C$ for 10 days, the concentrations of both HF and $Mn^{2+}$ were lower in the can containing $LiMn_2O_4$ blended with $LiNi_{0.8}Co_{0.2}O_2$ than that containing $LiMn_2O_4$ only. That reports clearly showed that this blending technique can prevent the decline in capacity caused by cycling or storage at elevated temperatures. However, not much work has been reported on the charge-discharge characteristics and related structural phase transitions for these composite cathodes. In this presentation, we will report our in situ x-ray diffraction studies on this mixed composite cathode material during charge-discharge cycling. The mixed cathodes were incorporated into in situ XRD cells with a Li foil anode, a Celgard separator, and a 1M $LiPF_6$ electrolyte in a 1 : 1 EC : DMC solvent (LP 30 from EM Industries, Inc.). For in situ XRD cell, Mylar windows were used as has been described in detail elsewhere. All of these in situ XRD spectra were collected on beam line X18A at National Synchrotron Light Source (NSLS) at Brookhaven National Laboratory using two different detectors. One is a conventional scintillation detector with data collection at 0.02 degree in two theta angle for each step. The other is a wide angle position sensitive detector (PSD). The wavelengths used were 1.1950 ${\AA}$ for the scintillation detector and 0.9999 A for the PSD. The newly installed PSD at beam line X18A of NSLS can collect XRD patterns as short as a few minutes covering $90^{\circ}$ of two theta angles simultaneously with good signal to noise ratio. It significantly reduced the data collection time for each scan, giving us a great advantage in studying the phase transition in real time. The two theta angles of all the XRD spectra presented in this paper have been recalculated and converted to corresponding angles for ${\lambda}=1.54\;{\AA}$, which is the wavelength of conventional x-ray tube source with Cu-$k{\alpha}$ radiation, for easy comparison with data in other literatures. The structural changes of the composite cathode made by mixing spinel $LiMn_2O_4$ and layered $Li-Ni_{1/3}Co_{1/3}Mn_{1/3}O_2$ in 1 : 1 wt% in both Li-half and Li-ion cells during charge/discharge are studied by in situ XRD. During the first charge up to ~5.2 V vs. $Li/Li^+$, the in situ XRD spectra for the composite cathode in the Li-half cell track the structural changes of each component. At the early stage of charge, the lithium extraction takes place in the $LiNi_{1/3}Co_{1/3}Mn_{1/3}O_2$ component only. When the cell voltage reaches at ~4.0 V vs. $Li/Li^+$, lithium extraction from the spinel $LiMn_2O_4$ component starts and becomes the major contributor for the cell capacity due to the higher rate capability of $LiMn_2O_4$. When the voltage passed 4.3 V, the major structural changes are from the $LiNi_{1/3}Co_{1/3}Mn_{1/3}O_2$ component, while the $LiMn_2O_4$ component is almost unchanged. In the Li-ion cell using a MCMB anode and a composite cathode cycled between 2.5 V and 4.2 V, the structural changes are dominated by the spinel $LiMn_2O_4$ component, with much less changes in the layered $LiNi_{1/3}Co_{1/3}Mn_{1/3}O_2$ component, comparing with the Li-half cell results. These results give us valuable information about the structural changes relating to the contributions of each individual component to the cell capacity at certain charge/discharge state, which are helpful in designing and optimizing the composite cathode using spinel- and layered-type materials for Li-ion battery research. More detailed discussion will be presented at the meeting.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.1
• /
• pp.99-110
• /
• 2018

In this study, oil of Platycodon grandiflorum seeds was prepared using supercritical carbon dioxide extraction (SCE) and its physicochemical indices as a new edible oil were investigated. Compared to Soxhlet solvent extraction, SCE under the condition of 6,000 psi at $40^{\circ}C$ produced more oil, especially from the roasted seeds to 32.7%. TLC analysis showed triacylglycerols accounted for most of the oil obtained from roasted Platycodon grandiflorum seeds by SCE similarly to commercial soybean oil or perilla seeds oil. The oil had highly unsaturated lipid with considerable amount of linoleic acid(73.27%) much more than two commercial oils followed by oleic acid(13.16%). Physicochemical properties of the oil were as follows; specific gravity, 0.92; dynamic viscosity, 45.37 cP; refractive index, 1.48; color, L=47.30, a=-3.69, b=25.72; iodine value, 141.57 g $I_2/100g$ oil; saponification value, 191.21 mg of KOH/g of oil; acid value, 2.60 mg of KOH/g of oil. Among those, refractive index, viscosity and iodine value, which were related to unsaturation degree of lipid, were ranged between those of two commercial oils. The oxidation stability of oil(2.03 hr) was also ranged between less stable perilla seeds oil(1.79 hr) and more stable soybean oil(2.94 hr) based on the induction time measured by Rancimat assay. In addition to extraction yield increase, seeds roasting provided further benefits such as reductions of cholesterol ester content and acid value without change in fatty acid composition. In conclusion, oil was extracted from the roasted Platycodon grandiflorum seeds at high yield by supercritical carbon dioxide and it seemed to have proper characteristics as a edible oil.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.38 no.5
• /
• pp.594-600
• /
• 2009

Quality characteristics of white lotus leaf tea (LLT) fermented with or without mycelial Paecilomyces japonica were investigated. Extraction yield and browning index of hot water extract from non fermented and fermented LLTs were higher than those of ethanol extract (p<0.05). In all LLTs, nutritional components such as total free sugar, free amino acids and minerals of hot water extracts were higher than those of ethanol extracts except for total organic acids (p<0.05). Contents of total free sugar and organic acids were markedly increased through fermentation process of mycelial Paecilomyces japonica. in the same solvent extracts (p<0.05). Contents of most taste components of fermented LLT were increased by mycelial solid fermentation (p<0.05), but total free amino acids of two extracts were decreased in the range of $37.1{\sim}67.2%$ as compared to non-fermented LLT. Fifty-nine volatile compounds were identified by GC and GC-MS, including 11 aldehydes, 14 alcohols, 11 ketones, 11 hydrocarbones and 12 acids. Aldehyde and ketone compounds were more identified in fermented LLT than in non-fermented LLT being abundant alcohol compounds by simultaneous steam distillation and extraction. The most abundant compounds of LLT identified in this study were curcumene followed by 2,6-bis(1,1-dimethylethyl)-4-methyl-phenol and cyclohexen. Main compounds of fermented LLT were 2,6-bis(1,1-dimethylethyl)-4-methyl-phenol, butanoic acid, furfural, benzaldehyde, hexanoic acid and 2(3H)-furanone.

• Korean Journal of Food Science and Technology
• /
• v.49 no.3
• /
• pp.304-310
• /
• 2017

The aim of this study was to compare the physicochemical properties of domestic and imported commercial plain wheat flour and dough. Four types of domestic wheat flour (DW; DW1-4) were compared to four types of imported wheat flour (IW; IW1-4). DWs exhibited lower moisture content, lightness (L), and whiteness, and higher protein content, redness (a), and yellowness (b), than those exhibited by IWs. Solvent retention capacity of DWs and IWs was similar; however, DWs showed higher gluten performance index. Pasting properties, analyzed by rapid visco analyzer (RVA), were similar for DW1, DW2, and IWs; however, DW3 and DW4 showed different RVA patterns. Considering that DW3 and DW4 were organic wheat flour, possible incorporation of damaged kernel might increase amylase activities resulting in decreased peak viscosity. Dough resistance (108.4-159.9 g) and extensibility (11.8-16.7 mm) of IWs were higher than those of DWs (78.0-118.7 g, 8.7-12.5 mm, respectively).