• Journal of Korean Society for Atmospheric Environment
• /
• v.21 no.6
• /
• pp.649-655
• /
• 2005

Automotive exhaust is suspected to be one of the main reasons of the rapid increase in greenhouse effect gases in ambient air. Although methane emissions are generally orders of magnitude lower than emissions of $CO_{2}$, the global warming potential (GWP) of methane is greater than that of $CO_{2}$. The environmental impact of methane emissions from vehicles is negligible and is likely to remain so for the foreseeable future. In this study, in order to investigate greenhouse gas emission characteristics from gasoline passenger cars, 20 vehicles were tested on the chassis dynamometer and methane emissions were measured. The emission characteristics by model year, mileage, vehicle speed were discussed. Test mode is CVS-15 mode that have been used to regulate for light-duty vehicle in Korea. It was found that $CH_{4}$ emissions showed higher for cold start, old model year and long mileage than hot start, new model year and short mileage, respectively. These results were compared with IPCC emission factors and the overall our results were anticipated to contribute for domestic greenhouse gas emissions calculation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.4
• /
• pp.484-489
• /
• 2012

The objective of this work presented here was focused on analysis of particulate matter and nitrogen oxide characteristics in ESC test mode from heavy-duty diesel engine installed on-road vehicles applicable to prime propulsion engine for marine vessels. The authors confirmed that a large quantity particulate matter were emitted in high power density condition, nitrogen oxide characteristics were dependent on exhaust gas temperature. Particulate matters were reduced by 1/100~1/1,000 times in post DPF with test modes but filtration efficiency was decreased in the engine power fluctuation. In the case of the high speed and power condition, the exhaust level of particulate matters was increased according to increment of temperature of gas flowing into DPF. The orders of magnitude for particle concentration levels from the analysis of size distribution of particulate matters of test engine was different. Both emitting nano-sized particles below 100nm regardless of DPF and non-DPF.

• Journal of Korean Academy of Nursing Administration
• /
• v.3 no.2
• /
• pp.41-59
• /
• 1997

This study surveyed nurses' value of reward and recognition level of organizational reward, and measured the fit of both. It also looked into the relationship between the reward fit and attitude of nurses toward their job and organization (job involvement${\cdot}$organizational commitment). It was planned to suggest the alternative of a future reward system. The sample consisted of 625 nurses of 8 private University Hospitals. Data for this study was collected from Mar. 25 to Apr. 17 by structured questionnaire. This study examined the differences of nurses' value of reward by their demographic characteristics, and looked into the relationship between the reward fit and job involvement${\cdot}$organizational commitment. Four instruments and a demographic questionnair were used to collect the data. Developed for myself and repaired by panel of judges, the value of reward scale and organizational reward scale consisted of 34 items on five points Likert-type scale. Developed by Kanungo and repaired by panel of judges, the job involvement scale measured overall job involvement on 7 items. The organizational commitment scale was developed by Mowday et al and repaired by panel of judges on 10 items. The data was analyzed by frequency, percentage, ranking, one-way ANOVA, Pearson's correlation coefficient, Chronbach alpha coefficient, t-test, SNK test, factor analysis with SPSS/PC+ progra,.Major findings are as follows 1. The mean of nurses' value of reward is 4.2435 and job content rewards are seen as the most important(M=4.5532). The following orders are seen as follows; financial rewards(M=4.4181), human realtion rewards(M=4.4130), establishment ${\cdot}$ facilities rewards(M=4.1632), professional rewards(M=4.1117), social status or prestige rewards(M=3.9228), career rewards(M=3.8816). Of 34 indivisual reward factors, the retainment allowance is seen to be thought of as the most important thing. 2. The mean of nurses' actual reward is 2.6035. The actual reward responded to the most extremely offered is job content rewards. The following orders are seen as follows ; human relation rewards(M=2.9420), financial rewards(M=2.7682), professional rewards(M=2.4601), social status or prestige rewards(M=2.3696), career rewards(M=2.3466), establishment ${\cdot}$ facilities rewards(M=1.9364). Of 34 indivisual reward factors, medical insurance benefits are felt to be most extremely offered. 3. The mean of fit of reward is -1.6874 and that means actual reward doesn't egual the value of the reward. What is offered mostly to nurses' value of reward is human relation rewards. The following orders are seen as follows; job content rewards(M=-1.5938), career rewards(M=-1.6381), social status of prestige rewards(M=-1.6382), financial rewards(M=-1.6836), professional rewards(M=-1.6854), establishment${\cdot}$facilities rewards(M=-2.3130). Of 34 indivisual factors, the item of fered most closely to nurses' value of reward is seen as the participation in educational programs at the nursing department of the hospital. 4. The mean of nurses' job involvement is 3.1987 and SD is 0.5667. 5. The mean of murses' organizational commitment is 2.9348 and SD is 0.6124, that is seen as a little lower than job involvement. 6. Significant value of reward differences were found among nurses by their demographic characteristics such as married status, tenure, academic career. 7. The fit of reward was significant related to job involvement and organizational commitment. When generalizing the result of this study, the value of reward, which nurses consider important and appropriate offers a reward that corresponds to the nurses' value of reward. This increases nurses' job and organization devotion further, as well as hospital effectiveness. It appears that nurses have recognized that the present reward offered in hospitals doesn't come up to their expectations so I think it is urgent to plan and perform the new reward system which is in accord with the nurses' reward fit.

• Journal of Life Science
• /
• v.24 no.4
• /
• pp.461-466
• /
• 2014

Three plant species, Aster sphathulifolius, Sedum oryzifolium, and Lysimachia mauritiana, native to the Dokdo Islands in South Korea, were examined for rhizosphere microorganisms by using 16S rDNA sequences. Nine species of rhizosphere microorganisms were isolated from the three native plant species, respectively. Phylogenetic analysis showed that the microorganisms could be classified into 19 species belonging to four phyla (Actinobacteria, Bacteroidetes, Firmicutes and Proteobacteria), and the characteristics of the microbes were confirmed. Rhizosphere microorganisms from the six orders (Bacillales, Corynebacteriales, Flavobacteriales, Micrococcales, Oceanospirillales, and Rhodobacterales) were isolated from S. oryzifolium. From L. mauritiana, microbes belonging to the seven orders (Bacillales, Flavobacteriales, Micrococcales, Oceanospirillales, Rhizobiales, and Rhodobacterales) were isolated. From A. sphathulifolius, the six orders of rhizosphere microorganisms (Alteromonadales, Bacillales, Corynebacteriales, Flavobacteriales, Micrococcales, and Rhizobiales) were isolated. These data showed that Actinobacteria and Proteobacteria were the dominant phyla for the rhizosphere of all three plants. To confirm the bacterial diversity in rhizospheres, Shannon's diversity index (H') was used at the genus level. In these data, the rhizosphere from S. oryzifolium and L. mauritiana had more diverse bacteria compared to that from A. sphathulifolius.

• The Journal of the Petrological Society of Korea
• /
• v.25 no.2
• /
• pp.151-163
• /
• 2016

The characteristics of the rock cleavage in Jurassic granite from Geochang were analysed. The evaluation for the three directions of rock cleavages was performed using the parameters such as (1) frequency of microcrack spacing(N), (2) total spacing(${\leq}1mm$), (3) mean spacing($S_{mean}$), (4) difference value($S_{mean}-S_{median}$) between mean spacing($S_{mean}$) and median spacing($S_{median}$), (5) density of spacing(${\rho}$), (6) difference value between two exponents for the whole range of the diagrams(${\lambda}_H-{\lambda}_L$), (7) mean value of exponent(${\lambda}_M$), (8) mean value of exponential constant($a_M$), (9) difference value between two exponents for the section under the initial points of intersection(${\lambda}t_H-{\lambda}t_L$), (10) mean value of exponent(${\lambda}t_M$) and (11) mean value of exponential constant($at_M$). The results of correlation analysis between the values of parameters for three rock cleavages and those for three planes are as follows. The values of (I) parameters(1, 2, 7 and 8) and (II) parameters(3, 4 and 5) are in orders of (I) H(hardway, (H1 + H2)/2) < G(grain, (G1 + G2)/2) < R(rift, (R1 + R2)/2) and (II) R < G < H. On the contrary, the values of the above two groups(I~II) of parameters for three planes show reverse orders. Besides, the values of parameter $6({\lambda}_H-{\lambda}_L)$, parameter $9({\lambda}t_H-{\lambda}t_L)$, parameter $10({\lambda}t_M)$ and parameter $11(at_M)$ for three planes are in orders of R(rift plane, (G1 + H2)/2) < H(hardway plane, (R2 + G2)/2) < G(grain plane, (R1 + H2)/2), H < G < R, H < R < G and R < H < G, respectively. The values of the above four parameters for three rock cleavages show the various orders of R < H < G, R < H < G, H < G < R and H < G < R, respectively. Meanwhile, the spacing values equivalent to the initial points of contact and intersection between the two directions of diagrams were derived. The above spacing values for three rock cleavages are in order of rift(R1 and R2) < grain(G1 and G2) < hardway(H1 and H2). The spacing values for three planes are in order of rift plane(G1 and H1) < hardway plane(R2 and G2) < grain plane(R1 and H2). In particular, the intersection angles for three rock cleavages and three planes are in order of rift and rift plane < hardway and hardway plane < grain and grain plane. Consequently, the two diagrams of rift(R1 and R2) and rift plane(G1 and H1) show higher frequency of the point of contact and intersection. These characteristics of change were derived through the general chart for three planes and three rock cleavages. Lastly, the correlation analysis through the values of parameters along with the distribution pattern is useful for discriminating three quarrying planes.

• The Journal of the Petrological Society of Korea
• /
• v.25 no.4
• /
• pp.311-324
• /
• 2016

The characteristics of the rock cleavage in Jurassic granite from Geochang were analysed. The evaluation for three quarrying planes and three rock cleavages was performed using the parameters such as (1) reduction ratio between the value of spacing and the value of length, (2) microcrack spacing frequency(N), (3) total spacing($1mm{\geq}$), (4) exponential constant(a), (5) magnitude of exponent(${\lambda}$), (6) mean spacing($S_{mean}$), (7) difference value($S_{mean}-S_{median}$) between mean spacing and median spacing($S_{median}$) and (8) density of spacing. Especially the close dependence between the above spacing parameters and the parameters from the spacing-cumulative frequency diagrams was derived. The discrimination factors representing three quarrying planes and three rock cleavages were acquired through these mutual contrast. The analysis results of the research are summarized as follows. First, the reduction ratios of frequency(N), mean value, median value, the above difference value($S_{mean}-S_{median}$) and density for three rock cleavages are in orders of G(grain, (G1 + G2)/2) < H(hardway, (H1 + H2)/2) < R(rift, (R1 + R2)/2), H < G $\ll$ R, H < G $\ll$ R, H < G < R and H < G $\ll$ R. The values of the above five parameters for three planes show the various orders of R'(rift plane) $\ll$ H'(hardway plane) < G'(grain plane), R' $\ll$ G' < H', R' < H' < G', R' < G' < H' and R' $\ll$ H' < G', respectively. Second, the values of (I) parameters(2, 3, 4 and 5) and (II) parameters(6, 7 and 8) are in orders of (I) H < G < R and (II) R < G < H. On the contrary, the values of the above two groups(I~II) of parameters for three planes show reverse orders. Third, to review the overall characteristics of the arrangement among the six diagrams, these diagrams show an order of R2 < R1 < G2 < G1 < H2 < H1 from the related chart. In other words, above six diagrams can be summarized in order of rift(R1 + R2) < grain(G1 + G2) < hardway(H1 + H2). These results indicate a relative magnitude of rock cleavage related to microcrack spacing. Especially, two parameters for each diagram, the above difference value($S_{mean}-S_{median}$) and mean spacing, could provide advanced information for prediction the order of arrangement among the diagrams. Finally, the general chart for three planes and three rock cleavages were made. From the related chart, three exponential straight lines for three rock cleavages show an order of R(R1 + R2) < G(G1 + G2) < H(H1 + H2). On the contrary, three lines for three planes show an order of H'(R2 + G2) < G'(R1 + H2) < R'(G1 + H1). Consequently, correlation of the mutually reverse order between three planes and three rock cleavages can be drawn from the related chart.

• Journal of Species Research
• /
• v.12 no.spc2
• /
• pp.54-59
• /
• 2023

To obtain unrecorded bacterial species from Korean islands, various samples were collected from the islands in 2022. After plating the samples on marine agar or Reasoner's 2A, and incubating aerobically, approximately 1,200 bacterial strains were isolated and identified using 16S rRNA gene sequences. A total of 10 strains showed ≥98.7% 16S rRNA gene sequence similarity with the bacterial species that were validly published but not reported in Korea. The unrecorded bacterial strains belong to three phyla, five classes, 10 orders, 10 families, and 10 genera, which are assigned to Sphingomonas, Falsirhodobacter and Asticcacaulis of the class Alphaproteobacteria; Colwellia and Halomonas of the class Gammaproteobacteria; Chitinophaga of the class Chitinophagia; Chryseobacterium of the class Flavobacteriia; Microlunatus, Zhihengliuella, and Streptomyces of the class Actinomycetia. The details of the unreported species including Gram reaction, colony and cell morphology, biochemical characteristics, and phylogenetic position are also provided in the description of the strains.

• Journal of Species Research
• /
• v.11 no.3
• /
• pp.143-154
• /
• 2022

To obtain unrecorded bacterial species in Korea, various marine samples were collected from Jeollanam-do Province, Korea in 2021. After plating the samples on marine agar and marine R2A agar, and incubating aerobically and anaerobically, approximately 1200 bacterial strains were isolated and identified using 16S rRNA gene sequences. A total of 30 strains showed ≥98.7% 16S rRNA gene sequence similarity with validly published bacterial species but not reported in Korea, indicating that they are unrecorded bacterial species in Korea. The unrecorded bacterial strains belonged to 4 phyla, 7 classes, 13 orders, 19 families, and 22 genera, which were assigned to Azospirllium, Loktanella, and Pseudovibrio of the class Alphaproteobacteria; Grimontia, Halomonas, Marinobacter, Microbulbifer, Photobacterium, Pseudoalteromonas, Pseudidiomarina, Ferrimonas, Shewanella, Simiduia, Thalassotalea, and Vibrio of the class Gammaproteobacteria; Priestia and Enterococcus of the class Bacilli; Persicobacter of the class Cytophagia; Aureivirga of the class Flavobacteriia; Propionigenium and Psychrilyobacter of the class Fusobacteriia; and Tepidibacter of the class Clostridia. The details of the unreported species including Gram reaction, colony and cell morphology, biochemical characteristics, and phylogenetic position are also provided in the description of the strains.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.180-185
• /
• 2004

Our previous study showed that although the hybrid rocket engine with swirling gaseous oxygen had high performance, a direct injection of LOX with swirl into the combustion chamber of the hybrid rocket engine lowered the performance of the engine, compared to that with gaseous oxygen. In order to clarify this reason, combustion tests of a small PMMA combustor with an inner port diameter of 2 mm were conducted in liquid oxygen flow by comparison with gaseous oxygen flow. Although the oxygen mass fluxes of LOX were about two orders of magnitude larger than those of gaseous oxygen, the fuel regression rate of LOX were remarkably smaller than those of gaseous oxygen. For both liquid and gaseous oxygen, diffusion flames in the port of the grain controlled the combustion process of PMMA in oxygen flow. These results may be explained by the fact that only small amount of LOX vaporized and consumed in the combustion with PMMA while flowing through the port due to relatively larger latent heat of injected liquid oxygen compared to the heat of release by combustion which depended on the burning surface area of PMMA.

• Journal of Species Research
• /
• v.12 no.4
• /
• pp.267-276
• /
• 2023

To obtain unrecorded bacterial species in Korea, various soils of coastal areas were collected from the Republic of Korea in 2022. After plating the samples on marine agar and incubating aerobically and anaerobically, approximately 1,700 bacterial strains were isolated and identified using 16S rRNA gene sequences. A total of 20 strains showed ≥98.7% 16S rRNA gene sequence similarity with validly published bacterial species but not reported in Korea, indicating they are unrecorded bacterial species in Korea. The unrecorded bacterial strains belonged to four phyla, six classes, 15 orders, 16 families, and 19 genera which were assigned to Blastomonas and Sphingomonas of the class Alphaproteobacteria; Pseudidiomarina, Kushneria, Salinicola, and Salinisphaera of the class Gammaproteobacteria; Evansella, Virgibacillus, and Paenibacillus of the class Bacilli; Cyclobacterium of the class Cytophagia; Pedobacter of the class Sphingobacteriia; and Demequina, Ornithinimicrobium, Blastococcus, Jatrophihabitans, Kineococcus, Glaciihabitans, Aeromicrobium and Streptomyces of the class Actinomycetes. The details of the 20 unreported species, including Gram reaction, morphology, biochemical characteristics, and phylogenetic position are also provided in the description of the strains.