• 대한전기학회논문지:전력기술부문A
• /
• 제53권8호
• /
• pp.432-437
• /
• 2004

Since the characteristic frequency is decreased in proportion to the fault distance, the characteristic frequency component may be insufficiently eliminated by a low-pass filter on a long transmission line. In order to set a standard for the cut-off frequency of the low-pass filter, this paper proposes a method for obtaining the characteristic frequencies due to line faults. The application results of the proposed method are presented for line to ground (LG) faults and line to line (LL) faults on a 345 kV 200 km overhead transmission line. The EMTP is used to generate fault signals under different fault locations and fault inception angles. By comparison between the characteristic frequencies obtained from the proposed method and the EMTP simulation, it is shown that the proposed method accurately obtains the characteristic frequency.

• 전기학회논문지
• /
• 제58권8호
• /
• pp.1585-1591
• /
• 2009

This paper describes a new method for extracting characteristic impedance of transmission line using Substrate Integrated Artificial Dielectric (SIAD). The new procedure to calculate the characteristic impedance of SIAD transmission line is described with the proper equations and basic transmission line theory. The characteristic impedance is determined as an almost fixed value in the proposed method, while it fluctuates according to frequency in the previous method. As the result, the effective dielectric constant of SIAD transmission line is calculated as a fixed value rather than fluctuating one. In order to show the validity of the proposed method, SIAD microstrip lines are simulated and measured, and characteristic impedances and effective dielectric constant are calculated and compared to the previous method.

• 한국정보통신학회논문지
• /
• 제23권10호
• /
• pp.1282-1289
• /
• 2019

임피던스 변환회로의 신호 전달특성(S21)을 측정하기 위해서는 두 개의 임피던스 변환회로를 대칭 연결하여야 한다. 하지만 두 개의 임피던스 변환회로를 대칭 연결한 회로의 신호 전달특성은 중간 연결 선로의 길이에 의해 영향을 받는다. 본 논문에서는 임피던스 변화회로의 정확한 신호 전달특성을 얻기 위한 중간 연결 선로의 길이를 수식으로 유도하였다. 수식을 이용하여 계산하면 4:1(50-Ω:12.5-Ω) 임피던스 변환회로의 정확한 신호 전달특성을 얻기 위한 중간 연결 선로의 전기적 길이는 약 45°이다. 계산된 연결 선로의 길이를 적용하여 1GHz에서 λ/4-마이크로스트립 임피던스 변환회로를 제작하여 신호 전달특성을 측정하였다. 제작된 대칭 연결된 임피던스 변환회로의 신호 반사 특성(S11)은 0.980GHz에서 -40.64dB, 신호 전달 특성(S21)은 -0.154dB였다. 이는 제작 회로에 대해 이론적으로 살펴본 중심 주파수의 987MHz 변화, 마이크로스트립 선로의 신호 손실 -0.15dB 값과 거의 동일한 값이다.

• 정보통신설비학회논문지
• /
• 제9권4호
• /
• pp.164-167
• /
• 2010

In this paper, an artificial transmission line of triangular-patch type with slots is proposed. This artificial transmission line is useful for miniaturizing the electrical lengths of conventional transmission lines. Also, this structure is easy to regulate the characteristic impedance and electrical lengths. The electrical lengths and the characteristic impedances of the proposed artificial transmission line with some parameters are researched and summarized The proposed artificial transmission line could be useful for compact designs for most of the passive microwave components. The optional-artificial transmission line is fabricated and measured at 2.45GHz.

• 통상정보연구
• /
• 제9권4호
• /
• pp.91-104
• /
• 2007

The recent stabilization of the Internet is now driving every aspect of life into an Internet presence. In the coming years, the Internet will see growth in numbers unlike the world has ever seen. The subject of this study is the Research Study on the Products Purchase Type of On-line Shopping Mall Buyer. Also, this paper is to examine the relations between customer satisfaction and intensity of repurchase intention and complaining behavior in on-line context. On-line shopping customer depths interview it led and the online afternotes trust evaluation dimension was discovered the of useful characteristic, intention characteristic, exaggerating characteristic and on-line afternotes with or without. From these results, this paper suggests effective marketing strategy to the marketer who plans to run on-line shopping mall in the near future and also to the marketer who plans to sell products through the on-line shopping mall.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 I
• /
• pp.350-353
• /
• 2003

In this paper, we designed and implemented a 10dB directional coupler with high directivity using branch line structure. The characteristic impedance of parallel branch line for 10 dB directional coupler is about 150 $\Omega$. To realize high characteristic impedance in microstrip line, we used the coupled line structure. The directional coupler were implemental and measured. The measured results show that the directivity is high than 24 dB.

• Journal of Electrical Engineering and Technology
• /
• 제2권1호
• /
• pp.29-34
• /
• 2007

The input and output impedances in a low voltage distribution system is one of the most important matters for power line communication because from the viewpoint of communication, the attenuation characteristic of the high frequency signals is greatly caused by impedance mismatch during sending and receiving. The frequency range is from 1MHz to 30MHz. Therefore, this paper investigates the input and output impedances in order to understand the characteristic of high frequency signals in the low voltage distribution system between a pole transformer and an end user. For power line communication, the model of Korea's low voltage distribution system is proposed in a residential area and then the low voltage distribution system is set up in a laboratory. In the low voltage distribution system, S parameters are measured by using a network analyzer. Finally, input and output impedances are calculated using S parameters.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.763-764
• /
• 2006

In this paper, optimized model was designed for the starting characteristic of the Single-Phase Line-Start Permanent Magnet Synchronous Motor by using the Design of Experiment. A field pole angle, thickness and distance from center axis of permanent magnet were selected as design factor. We executed the transient state characteristic analysis of 8 test models. The transient state characteristic analysis was executed by using the 2 dimensional Finite Element Method and the Time Difference Method. We checked the fact that the selected design factor affected starting characteristic of the Line-Start Permanent Magnet Synchronous Motor. Depend on this result we found the optimized design point by using the response optimization.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.485-488
• /
• 2001

This paper provides the result of analysis of the structure and I-V characteristics of D.C. 1500 V surge arresters which were installed in railway line currently. As Porcelain housed surge arresters have unstable elements such as exploding and dispersion, so it is thought that the system is protected more stably with replacement of polymer housing. The adoption of gap mitigates the voltage stress which is degradation factor of surge arresters and the research is needed to enhance the life characteristic in additive and manufacturing process. Therefore, it is thought that the research should be continued to develop homemade the surge arresters for D.C. railway line as well as transmission line.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.510-510
• /
• 2012

반도체, 디스플레이, 태양광 등의 공정에서 사용되는 웨이퍼의 크기가 증가하고, 생산률이 플라즈마의 밀도에 비례한다는 연구 결과가 발표되면서 대면적 고밀도 플라즈마 소스 개발에 대한 연구가 활발히 진행되고 있다. 특히, ECR, ICP, Helicon plasma 등 고밀도 플라즈마 소스에 대한 관심이 높아지고 있다. 이에 따라, 여러 개의 ICP를 결합한 multiple ICP를 이용해 대면적 고밀도 플라즈마 소스 개발을 진행했다. Multiple ICP의 경우 각 ICP 소스에 같은 power (current)를 공급해야만 균일한 플라즈마 방전이 발생되어 균일도를 확보 할 수 있다. Current controller 같은 추가적인 장비를 설치하지 않고, power를 분배하는 transmission line을 coaxial 형태로 설계하고 같은 길이로 병렬 연결함으로써 각각의 ICP소스에서 균일한 플라즈마를 방전시킬 수 있었다. Power generator에서 보는 각 ICP의 total impedance는 각 ICP 소스의 impedance와 coaxial 형태의 transmission line의 characteristic impedance, frequency, 길이의 함수로 구할 수 있고, 이 total impedance가 일정하기 때문에 current가 균등하게 분배되어 각 ICP소스에 균등한 power 분배가 가능한 것이다. 실질적으로 ICP 소스의 impedance는 플라즈마 방전 유무에 따라 변화하기 때문에 일정하게 유지하는 것은 어렵다. Transmission line의 characteristic을 사용함으로써 ICP의 impedance의 변화에 상관없이 Total impedance를 일정하게 유지시킴으로써 균등한 power 분배가 가능하다는 것을 연구했다. Frequency는 13,56MHz, characteristic impedance를 $50{\Omega}$ (coaxial cable)으로 고정하고, ICP 소스의 플라즈마 방전 유무/antenna turn/소스 위치에 따른 total impedance를 transmission line의 길이에 따라 측정하고, 이를 이론값, 그래프와 비교하였다. 특정 length에서 플라즈마 방전 유무(ICP의 impedance 변화)와 상관없이 비교적 일정한 total impedance를 유지하는 것을 확인 했다. 이것은 특정 길이를 갖는 coaxial형태의 transmission line를 연결하면, total impedance는 플라즈마 방전 유무로 발생하는 ICP의 impedance 변화와 상관없이 일정하게 유지되어 각 ICP소스에 균등한 파워 분배가 가능하다는 것을 보여준 결과이다. 이것을 토대로 frequency에 따라(또는 characteristic impedance에 따라) 균등한 파워 분배가 가능한 coaxial 형태 transmission line의 특정 길이를 구할 수 있고, 대면적 소스에서 균등한 파워 분배를 위한 병렬연결에 적용할 수 있을 것이다.