• 한국유체기계학회 논문집
• /
• 제10권4호
• /
• pp.29-38
• /
• 2007

In this study, flow structure in a two-stage centrifugal compressor for a turbo-chiller with the refrigerant, R134a, was numerically investigated at the design point of the compressor using a commercial code. Flow characteristics in the passages of impeller, diffuser and return channel were analyzed in detail including velocity vector, secondary flow, Mach number and pressure contours in blade spanwise and meridional plane for each stage. The estimation on the one-dimensional output from the preliminary design and three-dimensional shape of the impeller blade and the meridional shape of the return channel were performed through the flow analysis, while some numerical schemes and techniques including Multiple Frames of Reference technique, real gas property data and inlet boundary condition changes, which were used in CFD, were compared with their features. The results will be used as reference data for a new design of 3-D impeller shape to improve R134a compressor performance.

• 한국가시화정보학회지
• /
• 제17권1호
• /
• pp.85-92
• /
• 2019

Numerical visualization is conducted to confirm the variation of flow characteristics and pressure drop by the shape of channels on the cathode flow path in hydrogen fuel cells for unmanned aerial vehicles(UAVs). Generally, a light-weight fan is commonly used rather than a heavy air compressor at UAVS. However, in case of blower fan, a large pressure drop in the flow path causes the blocking of the oxygen supply to the fuel cell. Therefore, the uniformity of flow inside the cathode has to be achieved by changing the shape of the cathode. The flow channel, the duct shape, and the diameter of the fan are changed to optimize the flow path. As a result, it is confirmed that the optimal flow path can decrease the velocity difference between the center and outer flow by 1.8%. However, It should be noted that the channel size can increase the pressure drop.

• 한국군사과학기술학회지
• /
• 제24권6호
• /
• pp.655-663
• /
• 2021

In this paper, DFT-Based channel estimation with channel response mirroring is proposed and analyzed. In General, pilot symbols for channel estimation in MIMO(Multi-Input Multi-Output) OFDM(Orthogonal Frequency-Division Multiplexing) Systems have a diamond shape in the time-frequency plane. An interpolation technique to estimate the channel response of sub-carriers between reference symbols is needed. Various interpolation techniques such as linear interpolation, low-pass filtering interpolation, cubic interpolation and DFT interpolation are employed to estimate the non-pilot sub-carriers. In this paper, we investigate the conventional DFT-based channel estimation for noise reduction and channel response interpolation. The conventional method has performance degradation by distortion called "edge effect" or "border effect". In order to mitigate the distortion, we propose an improved DFT-based channel estimation with channel response mirroring. This technique can efficiently mitigate the distortion caused by the DFT of channel response discontinuity. Simulation results show that the proposed method has better performance than the conventional DFT-based channel estimation in terms of MSE.

• 대한기계학회논문집
• /
• 제19권5호
• /
• pp.1308-1318
• /
• 1995

The influence of varying rotation speed of both crystal and crucible was numerically investigated for the Czochralski silicon-crystal growth. Based on a simplified model assuming flatness of free surfrae, the Navier-Stokes Boussinesq equations were employed to identify the flow pattern, temperature distribution as well as the shape of the melt/crystal interface. The present results showed that the interface shape was relatively convex with respect to the melt at lower pulling rate and tended to be concave as the pulling rate increased. In particular, the experimentally observed gull-winged shape of the interface was qualitatively in agreement with the predicted shape. The rotation of crystal alone little affected the growth system. When the rotation speed of the crucible was increased, there occurred inversion of the interface shape from convex to concave pattern. At rapid rotation of the crucible, an interesting channel formation was predictied primarily due to the assumption of laminar flow.

• 대한조선학회논문집
• /
• 제40권4호
• /
• pp.22-29
• /
• 2003

New high-speed depressurized circulating water channel was designed by using the CFD code. Flow in the channel has free surface and pressure in the test section can be depressed. In this study, Flow separation and bubble occurrence were considered in designing the contraction nozzle shape for better flow uniformity Tn the test section. To supplement velocity defect due to the free surface, nozzle injection system more effective in high-speed flow was installed instead of drum system. Necessary power and injection techniques were proposed. And guide vane arrangement was analyzed to reduce the flow resistance and keep quiet free surface from ´surging´. Wave absorber was devised to reduce the wave resistance and to prevent the entrainment of air to the diffuser.

• 설비공학논문집
• /
• 제10권1호
• /
• pp.129-136
• /
• 1998

Pressure drop and heat transfer characteristics of a periodically fully developed flow in the flat channel with protrusions are investigated. The effects of shape and location of protrusion on the pressure drop and heat transfer are numerically analyzed in the present study. Taguchi method is used to optimize these parameters. It is found that the ratio of the height of protrusion to channel height shows larger influence on the pressure drop and heat transfer than the ratio of the length of protrusion to module length. As the height of protrusion increases, pressure drop and heat transfer increase, but if the height of protrusion exceeds 2/3 of the channel height, there is a substantial pressure drop. The results also show that the optimal length and height of protrusion are half of the module length and half of the channel height, respectively.

• 한국인터넷방송통신학회논문지
• /
• 제8권2호
• /
• pp.49-55
• /
• 2008

To address the convergence issue of power control algorithms, a number of algorithms have been developed hat shape the dynamics of up-link power control for cellular network. Power algorithms based on fixed point iterations can be accelerated by the use of various methods, one of the simplest being the use of Newton iterations, however, this method has the disadvantage which not only needs derivatives of the cost function but also may be weak to noisy environment. we showed performance of the power control schemes to solve the fixed point problem under static or stationary channel. They proved goof performance to solve the fixed point problem due to their predictor based optimal control and quadratic convergence rate. Here, we apply the proposed power control schemes to the problem of the dynamic channel or to dynamic time varying link gains. The rigorous simulation results demonstrated the validity of our approach.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 춘계학술대회
• /
• pp.81-84
• /
• 2006

To investigate the characteristics of water droplet on the gas diffusion layer from both upper-view and side-view of flow channel, a rig test apparatus was designed and fabricated with L-shape acryl plate in a $1mm{\times}1mm$ micro-channel. This experimental device is used to simulate the single droplet growth and its transport process under fuel cell operating condition. As a first step, we investigated the growth and transport of single water droplet with working temperature and air flow velocity. The contact angle and its hysteresis of water droplet at departing moment are measured and analyzed. It is expected that this study can provide the basic understanding of liquid water droplet behavior in gas flow channel and GDL interface during the PEM fuel cell operation.

• Journal of Electrochemical Science and Technology
• /
• 제14권1호
• /
• pp.38-50
• /
• 2023

Proton exchange membrane fuel cell (PEMFC) is a portable and clean power generation device. The structural arrangement of the flow field has a significant influence on the delivery efficiency of PEMFC. In this article, a new bionic flow channel is designed based on the inspiration of a spider shape. The branch channel width and branch corner are studied as the focus, and its simulation is carried out by the method of computational fluid dynamics (CFD). The results show that when channel width/rib width and corner of the branch are 1.5 and 130° , respectively, it is the best numerical combination and the cell comprehensive performance is excellent. The final model using this numerical combination is compared with the traditional flow channel model to verify the advancement of this scheme.

• 센서학회지
• /
• 제32권5호
• /
• pp.280-284
• /
• 2023

In this study, a prototype micro-scale photomask and microfluidic channel mold were fabricated using the thermal shrinkage of the polymer. A polystyrene (PS) sheet was used as the heat-shrink polymer, and the patterns of the photomask and microchannel are interdigitated electrodes. Patterns were formed on the PS sheets using a commercial laser printer. The contraction ratio of the PS sheet was approximately 60% at a temperature of 150 ℃, and the transmittance was reduced by approximately 0% at a wavelength of 365 nm. The microfluidic channel had a round shape. The proposed technique is simple, facile, and inexpensive for fabricating a micro-scale photomask and microfluidic channel mold and does not involve the use of any harmful materials. Thus, this technique is well-suited for fabricating diverse micro-scale patterns and channels for prototype devices, including sensors.