• ETRI Journal
• /
• 제45권6호
• /
• pp.974-981
• /
• 2023

This paper presents a transition-limited pulse-amplitude modulation (TLPAM) signaling method to enable a high data rate and robust wireline communications. TLPAM signaling addresses the impact of high intersymbol interference (ISI) ratios in conventional M-ary PAM signaling methods by limiting the maximum voltage transition level between adjacent symbols. The implementation of a TLPAM signaling encoder is realized by setting back the most significant bits (MSBs) in the queue. The correlation between TLPAM's maximum transition level, effective data rate, and eye width/height is analyzed with various channel loss parameters, followed by characterization and measurement results with a realistic channel setup. The analysis and experimental results reveal the effectiveness of the proposed TLPAM signaling scheme for achieving a high data rate with minimal interference.

• 국제강구조저널
• /
• 제18권5호
• /
• pp.1801-1817
• /
• 2018

This paper presents the numerical parametric analysis on the loading capacity of Channel purlins with screw-fastened sheeting, in which the effects of anti-sag bar and corrugated steel sheet on the ultimate capacity are studied. Results show that the setup of anti-sag bars can reduce the deformations and improve the ultimate capacity of C purlins. The traditional method of setting the anti-sag bars in the middle of the web is favorable. The changing of sheeting type, sheeting thickness and rib spacing has significant effects on the ultimate capacity of C purlins without anti-sag bars, compared with those with anti-sag bars. The proposed design formulas are relatively consistent with the calculations of EN 1993-1-3:2006, which is different from those of GB 50018-2002.

• International Journal of Fluid Machinery and Systems
• /
• 제3권1호
• /
• pp.11-19
• /
• 2010

The performance of the crossover system of a centrifugal compressor stage consisting of static components of $180^{\circ}$ U-bend, return channel vanes and exit ducting with a $90^{\circ}$ bend is investigated. This study is confined to the assessment of performance of the crossover system by varying the shape of the return channel vanes. For this purpose two different types of Return Channel Vanes (RCV1 and RCV2) were experimentally investigated. The performance of the crossover system is discussed in terms of total pressure loss coefficient, static pressure recovery coefficient and vane surface pressure distribution. The experimentation was carried out on a test setup in which static swirl vanes were used to simulate the flow at the exit of an actual centrifugal compressor impeller with a design flow coefficient of 0.053. The swirl vanes are connected to a mechanism with which the flow angle at the inlet of U-bend could be altered. The measurements were taken at five different operating conditions varying from 70% to 120% of design flow rate. On an overall assessment RCV1 is found to give better performance in comparison to RCV2 for different U-bend inlet flow angles. The performance of RCV2 was verified using numerical studies with the help of a CFD Code. Three dimensional sector models were used for simulating the flow through the crossover system. The turbulence was predicted with standard k-$\varepsilon$, 2-equation model. The iso-Mach contour plots on different planes and development of secondary flows were visualized through this study.

• 한국정보과학회논문지:정보통신
• /
• 제36권5호
• /
• pp.456-469
• /
• 2009

본 논문에서 ECOT(Estimated Channel Occupancy Time)이라는 새로운 무선 링크 성능 지표를 제시하며, 이를 기반으로 멀티 홉 무선 메쉬 네트워크 환경에서 종간간 높은 수율을 얻고자 한다. ECOT의 핵심적인 특징은 다양한 형태의 IEEE 802.11 MAC(Medium Access Control) 환경에서 적용이 가능하다는 점이다. 우리는 802.11 DCF(Distributed Coordination Function), 802.11e EDCA(Enhanced Distributed Channel Access) with BACK(Block Acknowledgement), 802.11n A-MPDU(Aggregate MAC Protocol Data Unit)와 같은 다양한 형태의 링크 계층 구조를 고려하며, 이와 같은 다양한 환경에서 제안하는 ECOT이 기 제안된 다른 성능 지표 방법론과 비교하여 높은 종단간 수율 성능(이득: $8.5{\sim}354.4%$)을 보여줄 수 있다는 것을 확인하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.922-925
• /
• 2004

Bluetooth technology is essentially a method for wireless connection of a diverse set of devices ranging from PDAs, mobile phone, notebook computers, to another equipments. The bluetooth system supports both point-to-point connection and point-to-multipoint connections. In point-to-multipoint connection, the channel is shared among several bluetooth devices. Two or more devices sharing the same channel form a piconet. There is one master device and up to seven active slave devices in a piconet. The radio operates in the unlicensed 2.45GHz ISM band. This allows users who travel world-wide to use bluetooth equipments anywhere. Since the link is based on frequency-hop spread spectrum, multiple channels can exist at the same time. The Bluetooth standard has been suggested that Bluetooth equipments can be used in the short-range, maximum 100 meters . It has been defined that the time takes to setup and establish a bluetooth connection among devices is 10 seconds. It is a long time and may be a cause to lose a chance of finding other non-fixed devices. We propose a routing protocols for scatternets which can be used to control a mobile units(MUs) in this network. The proposed routing protocol is composed of two kinds of bluetooth information, access point(AP) and MU.

• 제어로봇시스템학회논문지
• /
• 제10권11호
• /
• pp.1052-1057
• /
• 2004

Bluetooth technology is essentially a method for wireless connectivity of a diverse set of devices ranging from PDAs, mobile phone, notebook computers, to another equipments, The bluetooth system both point-to point connection and point-to multipoint connection. In point-to multipoint connection, the channel is shared among several bluetooth devices. Two or more devices sharing the same channel form a piconet. There one master device and up to seven active slave devices in a piconet. The radio operates in the unlicensed 2.45GHz ISM band. This allows users who travel world-wide to use bluetooth equipments anywhere. Since the link is based on frequency-hop spread spectrum, multiple channels can exist at the same time. The bluetooth standard ha s been suggested that bluetooth equipments can be used in the short-range, maximum 100 meters. It has been defined that the time takes to setup and establish a bluetooth connection among devices is 10 seconds. It is a long time and may be a cause to lose a chance of finding other non-fixed devices. We propose a routing protocols for scatternets which can be used to control a mobile units(MUs) in this network. The proposed routing protocol is composed of two kinds of bluetooth information, access point(AP) and MU.

• 한국지반공학회논문집
• /
• 제22권12호
• /
• pp.15-24
• /
• 2006

공학적 물성치로서의 저변형율에서의 전단탄성계수의 결정은 다양한 토목분야에서 매우 중요하다. 이러한 지반의 전단 파탄성계수 주상도는 비파괴 탄성파 실험을 통하여 결정될 수 있다. 비파괴 탄성파 실험은 대상지반의 분산곡선을 결정하고, 결정된 분산곡선에 대한 역산을 수행하여 대상지반의 전단파탄성계수 주상도를 결정한다. 이러한 비파괴 탄성파 실험은 결정되는 분산곡선의 종류에 따라 크게 두가지로 구분할 수 있다. 첫번째는 겉보기 속도 분산곡선을 사용하는 방법과, 두번째는 모드 분산곡선을 사용하는 방법이다. 모드 분산곡선을 결정, 역산에 사용하는 방법의 경우, 계산 시간의 감소와 역산의 모호성을 감소시킬 수 있다. 모드 분산곡선을 결정하기 위해서는 다수의 감지기를 사용하는 다채널 표면파 실험을 통해서만 가능하다. 이러한 다수 감지기의 필요성은 현장에서의 실제 적용에 있어 실용성을 떨어뜨릴 수 있다. 본 논문에서는 HWAW방법을 표면파 모드 분해 및 모드 분산곡선 결정에 적용하였다. 제안된 방법은 $1{\sim}3m$의 감지기 간격을 가지는 2개의 감지기를 사용하는 짧은 실험구성을 사용하여 대상지반의 모드 분산곡선을 결정한다. 제안된 방법을 검증하기 위하여 수치 모의 실험과 현장실험을 수행하였으며, 이를 통하여 제안된 방법의 타당성을 확인할 수 있었다.

• Journal of Mechanical Science and Technology
• /
• 제19권2호
• /
• pp.716-727
• /
• 2005

Comprehensive measurements for velocity and temperature fields have been conducted. A Micro PIV 2-color LIF system have been setup to measure the buoyancy driven fields in a 1-mm heated channel with low Grashof-Prandtl numbers [$86]. Fluorescence microscopy is combined with an MPIV system to obtain enough intensity images and clear pictures from nano-scale fluorescence particles. The spatial resolution of the Micro PIV system is $75{\mu}m\;by\;67{\mu}m$ and error due to Brownian motion is estimated $1.05\%$. Temperature measurements have achieved the $4.7\;{\mu}m$ spatial resolution with relatively large data uncertainties the present experiment. The measurement uncertainties have been decreased down to less than ${\pm}1.0^{\circ}C$ when measurement resolution is equivalent to $76\;{\mu}m$. Measured velocity and temperature fields will be compared with numerical results to examine the feasibility of development as a diagnostic technique.

• 한국멀티미디어학회논문지
• /
• 제16권9호
• /
• pp.1067-1076
• /
• 2013

Known as an important criterion that evaluates performance of future high-speed backbone networks, burst data loss ratio is well-studied in Optical Burst Switching networks. Current literatures mostly focus on reduce burst loss ratio without considering the system stability and link utilization after reducing. In this paper, we propose a novel framework which comes from feedback theoretic to dynamically control burst loss ratio in OBS. The proposed scheme tries to track the pre-set values of burst loss ratio and increases the stability and link utilization degree. The simulation results show that measured burst loss ratio always tracks setup reference with small errors, wavelength channel utilization is increased up to 2% and the system stability is also improved.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1384-1387
• /
• 2003

Pressurization test is usually required in aircraft full-scale static test. There are several test conditions including pressurization of cockpit, fuselage fuel tank, air inlet duct for T-50 full-scale static test. In this paper, the test conditions, equipment, piping analysis for the pressurization test are introduced. Tank simulation test is performed to verify the validity of piping analysis and to find good tuning parameters for the pressurization channel in the servo controller. Several test setup for pressurization of T-50 test is introduced. Test article volume is filled by form, $60%{\sim}80%$ volume is reduced for the T-50 full-scale static test. Pressurization system is connected to servo controller which also controls hydraulic actuator. Load and pressure control is synchronized by using the same servo controller during T-50 test. Typical control result for pressurization test condition is shown. Pressurization tests of T-50 full-scale static test was completed successfully.