• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.3
• /
• pp.261-264
• /
• 2009

We present a three-dimensional (3D) particle focusing channel using the positive dielectrophoresis (pDEP) guided by a dielectric structure between two planar electrodes. The dielectric structure between two planar electrodes induces the maximum electric field at the center of the microchannel, and particles are focused to the center of the microchannel by pDEP as they flow from the single sample injection port. Compared to the previous 3D particle focusing methods, the present device achieves the simple and effective particle focusing function without any additional fluidic ports and top electrodes. In the experimental study, approximately 90 % focusing efficiency were achieved within the focusing length of 2mm, on both x-z plane (top-view) and y-z plane (side-view) for $2{\mu}m$-diameter polystyrene (PS) bead at the applied voltage over 15 Vp-p (square wave) and at the flow rate below 0.01 ${\mu}l$/min. The present 3D particle focusing channel results in a simple particle focusing method suitable for use in integrated microbiochemical analysis system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.1C
• /
• pp.113-119
• /
• 2009

The training sequence with the appropriate length for equalization and initial synchronization is necessary before sending the pure data in the burst transmission type DS-UWB system. The length of the training sequence is one of the factors which make throughput decreased. The noble structure with the variable length of the training sequence whose length can be adaptively tailored according to the channel conditions (CM1,CM2,CM3,CM4) in the DS-USB systems is proposed. This structure can increase the throughput without sacrificing the performance than the method with fixed length of training sequence considering the worst case channel conditions. Simulation results under IEEE 802.15.3a channel model show that the proposed scheme can achieve higher throughput than a conventional one with the slight loss of BER performance. And this structure can reduce the computation complexity and power consumption with selecting the short length of the training sequence.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.421-424
• /
• 2004

As the deep sub-micron devices are recently integrated high package density, novel process method for sub $0.1{\mu}m$ devices is required to get the superior thin gate oxide characteristics and reliability. However, few have reported on the electrical quality and reliability on the thin gate oxide. In this paper I will recommand a novel shallow trench isolation structure for thin gate oxide $30{\AA}$ of deep sub-micron devices. Different from using normal LOCOS technology, novel shallow trench isolation have a unique 'inverse narrow channel effects' when the channel width of the devices is scaled down shallow trench isolation has less encroachment into the active device area. Based on the research, I could confirm the successful fabrication of shallow trench isolation(STI) structure by the SEM, in addition to thermally stable silicide process was achiever. I also obtained the decrease threshold voltage value of the channel edge and the contact resistance of $13.2[\Omega/cont.]$ at $0.3{\times}0.3{\mu}m^2$. The reliability was measured from dielectric breakdown time, shallow trench isolation structure had tile stable value of $25[%]{\sim}90[%]$ more than 55[sec].

• International Commerce and Information Review
• /
• v.14 no.2
• /
• pp.81-119
• /
• 2012

In order to maintain high level of control over and close coordination of foreign marketing activities, export manufacturers often consider vertical integration strategy into global distribution. However, full integration is not always a feasible option. The purpose of this study is to investigate the alternative ways to achieve optimal level of control over export channel system for desirable channel performance. This study investigates different options for integration of the vertical channel structure, and examines their effect on the performance. The findings of this study suggest different combination of ownership and coordination level has varying impact upon channel performance: efficiency, effectiveness, and adaptiveness. This implies exporters may achieve desirable performance control over export channel without fully integrating the channel via ownership.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.2
• /
• pp.583-599
• /
• 2015

We apply the Bayesian matching pursuit (BMP) algorithm to the estimation of time-frequency selective channels in orthogonal frequency division multiplexing (OFDM) systems. By exploiting prior statistics and sparse characteristics of propagation channels, the Bayesian method provides a more accurate and efficient detection of the channel status information (CSI) than do conventional sparse channel estimation methods that are based on compressive sensing (CS) technologies. Using a reasonable approximation of the system model and a skillfully designed pilot arrangement, the proposed estimation scheme is able to address the Doppler-induced inter-carrier interference (ICI) with a relatively low complexity. Moreover, to further reduce the computational cost of the channel estimation, we make some modifications to the BMP algorithm. The modified algorithm can make good use of the group-sparse structure of doubly selective channels and thus reconstruct the CSI more efficiently than does the original BMP algorithm, which treats the sparse signals in the conventional manner and ignores the specific structure of their sparsity patterns. Numerical results demonstrate that the proposed Bayesian estimation has a good performance over rapidly time-varying channels.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.8
• /
• pp.759-764
• /
• 2004

This paper proposes a method that estimates MIMO channel characteristics analytically using a 3D ray tracing propagation model. We calculate the discrete spatial correlation between sub-channels by considering phase differences of paths, and using this, estimate the mean capacity upper bound of MIMO channel by Jensen's inequality. This analysis model is a deterministic model that do not approach stochastically through measurement nor approach statistically through Monte-Carlo simulations, so this model has high efficiency for time and cost. And based on the electromagnetic theory, this model may analyze quantitatively the parameters which can affect the channel capacity - antenna pattern, polarization mutual coupling, antenna structure and etc. This model may be used for the development of an optimal antenna structure for MIMO systems.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.6A
• /
• pp.660-666
• /
• 2004

Transmitted data may be compensated by using estimated channel values that are obtained with pilot symbols in OFDM-CDMA systems. Generally, a USE (Minimum Mean-Squared Error) estimator using correlations between pilot symbols gives good results, but its structure is so complicated. Starting with a modification of PA (Pilot-Aided) algorithm using pilot symbols and PADD (Pilot-Aided Decision-Directed) algorithm using both pilot and data symbols, a new channel estimation algorithm with more simpler structure is proposed. The performance of this algorithm is evaluated with varying mobile speed in a Ralyleigh multipath fading environment through computer simulations. The simulation results show that the proposed channel estimation algorithm outperforms a conventional PA algorithm.

• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.5
• /
• pp.571-579
• /
• 2007

This study was conducted to qualify the equality of the flow distribution from open channel between rapid mixing basin and flocculation basins in a domestic full-scale water treatment plant, and suggest a remedy for improving the equality. In order to evaluate the feasibility of the suggested remedy, computational fluid dynamics (CFD) technique are used, and for verifying the CFD simulation results wet tests were carried out for the pilot scale channel based on geometric similarity. From the results of CFD simulation and wet tests, it was investigated that the modification of hydraulic structure in the distribution channel, which is to install the longitudinal orifice baffle in flow direction, could improve the equality of the flow distribution. Also, in the case that Froude number is relatively small (Froude number <<0.03), the open ratio of orifices on the installed baffle hardly affects the equality of flow distribution.

• Journal of Navigation and Port Research
• /
• v.36 no.8
• /
• pp.631-635
• /
• 2012

Underwater acoustic communication has multipath error because of reflection by sea-level and sea-bottom. The multipath of underwater channel causes signal distortion and error floor. In this paper, in order to design an efficient packet structure, we employ channel coding scheme and phase recovery algorithm. For channel coding scheme, half rate LDPC channel coding scheme with N=1944 and K=972 was used. Also, decision directed phase recovery was used for correcting phase offset induced by multipath. Based on these algorithms, we propose length of data for optimal packet structure in the environment of oceanic experimentation.

• Journal of IKEEE
• /
• v.27 no.3
• /
• pp.303-307
• /
• 2023

In this paper, the creation of an Electron-Hole Pair due to Total Ionizing Dose (TID) effects inside the oxide of a Buried Channel Array Transistor (BCAT) device is induced, resulting in an increase in leakage current and threshold due to an increase in hole trap charge at the oxide interface. By comparing and simulating changes in voltage with the previously proposed Partial Isolation Buried Channel Array Transistor (Pi-BCAT) structure, the characteristics in leakage current and threshold voltage changed regardless of the increased oxide area of the Pi-BCAT device, compared to the asymmetrically doped BCAT structure. It shows superiority.