• Journal of Mechanical Science and Technology
• /
• v.20 no.10
• /
• pp.1576-1589
• /
• 2006

Most of surface water ways in Egypt suffer from the infestation of aquatic weeds especially submerged ones which cause lots of problems for the open channels and the water structures such as increasing water losses, obstructing the water flow, and reducing the efficiency of the water structures. Accurate simulation of the water flow behavior in such channels is very essential for water distribution decision makers. Artificial Neural Network (ANN) has been widely utilized in the past ten years in civil engineering applications for the simulation and prediction of the different physical phenomena and has proven its capabilities in the different fields. The present study aims towards introducing the use of ANN technique to model and predict the impact of the existence of submerged aquatic weeds on the hydraulic performance of open channels. Specifically the current paper investigates utilizing the ANN technique in developing a simulation and prediction model for the flow behavior in an open channel experiment that simulates the existence of submerged weeds as branched flexible elements. This experiment was considered as an example for implementing the same methodology and technique in a real open channel system. The results of current manuscript showed that ANN technique was very successful in simulating the flow behavior of the pre-mentioned open channel experiment with the existence of the submerged weeds. In addition, the developed ANN models were capable of predicting the open channel flow behavior in all the submerged weeds' cases that were considered in the ANN development process.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.4
• /
• pp.15-22
• /
• 2004

This paper presents the channel analysis considering power distribution network(PDN) system of PCB. For achieve the target PDN system we proposed the useful design approach for acquiring the characteristic target of power distribution network in overall frequency ranges. The proposed method is based on the hierarchical approach related to frequency ranges and the path-based equivalent circuit model to consider the interference of the current paths between the decoupling capacitors and the board through it is a lumped model for fast and easy calculation, experimental results show that the proposed model is almost as precise as the numerical analysis. The analysis of PDN system shows that although the effective inductance of package dominatly affects the power noise and the signal transfer through data channel, the board PDNs also can not be neglected for achieving the accurate channel signaling. Therefore, we must design concurrently the chip, package, and board from the initial spec design of high speed digital system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.8
• /
• pp.1518-1527
• /
• 1994

An algorithm for BPSK demodulation of which channel is an electric distribution line is developed, and realized in this paper. To realize the BPSK demodulation by microprocessor, BPSK signal that is received through the distribution line must be converted to digital signal. A hardware which converts BPSK signal to digital one has been designed in this paper, and an algorithm for BPSK demoduation of which channel is distribution line has been also developed in algorithm for BPSK demoduation of which channel is distribution line has been also developed in this paper by paying the attention to the fact that a modulated point appears up and down according to the rising edge and falling edge of the modulated binary signal if the carrier frequency is even times to the modulated binary signal, and by paying the attention to the fact that the signal duration or modulated point is twice of the other point. The microprocessor demodulation system with the algorithm has been realized. The system proved to have 0.02%(or less) bit error rate in real BPSK demodulation.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.5
• /
• pp.397-403
• /
• 2015

In this study, water distribution inside a proton exchange membrane fuel cell (PEMFC) was measured experimentally. Water distribution is non-uniform because of vigorous chemical reaction and mass transport and has been difficult to measure experimentally. Therefore, much research relied on indirect measuring methods or numerical simulations. In this study, several mini temperature-humidity sensors were installed at the channel for measuring temperature and humidity of the flowing gas throughout the channel. Only one of two electrode channels was humidified externally, and the humidity distribution on the other side was measured, enabling the observation of water transport characteristics under various conditions. Diffusion through the membrane became more vigorous as the temperature of the humidifier rose, but at high current density, electro-osmotic drag became more effective than diffusion.

• Membrane Journal
• /
• v.6 no.1
• /
• pp.44-52
• /
• 1996

For the purpose of the optimal design of a frame and plate type of pervaporation module, model equations which can predict the effects of feed flow condition on the temperature distribution of the feed developed in the module were established and the temperature distribution with feed flow condition was investigated through the model si$$\mu$ation. With increasing the Reynolds number of feed flow in the module, the flow velocity gradient in the channel height-direction as well as the volume rate of feed which acts as energy source for the evaporation of perrneants on the permeate-side surface of a membrane increased to such an extent that both mass and heat flux in the channel height direction could increase and the temperature drop of feed due to the evaporation of the permeant could be reduced correspondingly. A decrease in channel height caused the temperature drop of feed because of decreasing feed flow in the module. It was observed that the si$$\mu$ation result on the effect of Re on the temperature distribution of feed in the module has an agreement with experiment.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.878-881
• /
• 2011

In this paper, drain induced barrier lowering(DIBL) has been analyzed as one of short channel effects occurred in double gate(DG) MOSFET to be next-generation devices. Since Gaussian function been used as carrier distribution for solving Poisson's equation to obtain analytical solution of potential distribution, we expect our results using this model agree with experimental results. DIBL has been investigated according to projected range and standard projected deviation as variables of Gaussian function, and channel thickness and channel doping intensity as device parameter. Since the validity of this analytical potential distribution model derived from Poisson's equation has already been proved in previous papers, DIBL has been analyzed using this model.

• Journal of Distribution Science
• /
• v.12 no.7
• /
• pp.53-61
• /
• 2014

Purpose - This study focuses on "large-scale marts," which is a typical discount-based retail channel (hereinafter, DRC), and provides practical managerial implications by applying the KD-SQS service quality factor based on customers' experiential perspective by developing and applying existing service measures. Research design, data, and methodology - The research subjects include adults who have experienced "large-scale marts." The research involved SPSS 20.0 and AMOS 19.0 packages; path analysis is used to analyze structural relationships. Results - First, physical aspects, human interaction, and additional convenience aspects of service quality have statistically significant influence on service value. Second, physical aspects, human interaction, and policy have statistically influence on store loyalty. Third, service value influences store loyalty. Fourth, service guarantee adjusts the relationship between service quality, service value, and store loyalty in terms of human interaction and policy. Conclusion - Among service quality measures, improving service value through personal service needs to be prioritized, while we need to develop different methods for the service guarantee system to effectively influence service value and store loyalty.

• Journal of Distribution Research
• /
• v.7 no.2
• /
• pp.1-19
• /
• 2003

This study intends to explore the relationship between export motivating factors and export channel-structure. Two proactive motivating factors (market-opportunity development and productivity improvement) and one reactive motivating factor (business-risk hedge) were extracted from the survey data collected from Korean exporting firms. The data show that the two proactive motives enhance the likelihood of using the export channels that allow strong controls over export-marketing activities. This study also finds that these proactive motives tend to increase the amount of relationship investment in an export distribution channel.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.6
• /
• pp.1077-1082
• /
• 2009

Wireless Mesh Network(WMN) is wireless backbone networks technique which has ease of network configuration and cost of advantage. Recently, WNM released a new product, but most of existing research and technology analysis the performance through the simulation. This paper build the wireless mesh network testbed for actual situation. Testbed supports multi-channel multi-interface using bridge, the Wireless Distribution System and dynamic location-based routing protocol. This routing protocol strongly design against wireless interference using metric for link channel change and real distance. Then, the address of mesh clients assigned by the centralized address management server. Mesh clients is designed and implemented to manage network through Simple Network Management Protocol.

• The KSFM Journal of Fluid Machinery
• /
• v.15 no.5
• /
• pp.11-19
• /
• 2012

The main function of fuel cell manifold is to render reactants distribution as uniform as possible into a fuel cell stack. The purpose of this study is to numerically investigate the effects of stack manifold design on reactants distribution within a fuel cell stack. Four manifold designs with different manifold entrance shapes (expansion or diffuser) and different values of the extra width between the cell outer channel and manifold side wall are considered and applied to the fuel cell stack consisting of 50 cells. Since the fuel cell stack geometry involves several millions of grid points for numerical calculations, a parallel computing methodology is employed to substantially reduce the computational time and overcome the memory requirement. The numerical simulations are carried out and calculated results clearly demonstrate that both the manifold entrance shape and extra width have a substantial influence on manifold performance, controlling the degree of flow separation and entrance length for fully developed flow in the manifold channel. Finally, we suggest the optimum design of fuel cell manifold based on the simulation results.