• Korean Journal of Heritage: History & Science
• /
• v.49 no.3
• /
• pp.154-201
• /
• 2016

During the Incipient and Early Silla phases, which witnessed the establishment and development of the ancient Silla state, the Wolseong North Burial Ground functioned as not only the central burial ground in the Gyeongju region of the capital of Silla but also as the central burial ground of the whole Silla state. Wolseong North Burial Ground is where transformations in Silla funerary architecture first occurred. As such, an empirical study of the tombs constructed at this burial ground can be regarded as a starting point from which an understanding of the development of the tomb culture of the Silla state may be achieved. This paper therefore aims to examine the changing nature of the tomb culture of the Early Silla phase through the burial data of Wolseong North Burial Ground and the Gyeongju region. Wooden chamber tombs were constructed from the late phase of Saroguk. At Wolseong North Burial Ground, which eventually developed into the central burial ground of the Gyeongju region, wooden chamber tombs embellished with stone packing emerged during the Incipient Silla phase; wooden chamber tombs with stone mounds, on the other hand, first appeared in the Early Silla phase and eventually became established as the central tomb type. A key difference between the wooden chamber tomb embellished with stone packing and the wooden chamber tomb with stone mound is that, in the case of the latter, stones were packed not only around sides of the wooden structure that acted as the burial chamber but also on top of this structure. The addition of a high earthen mound surrounded by protective ring of stones is another distinctive feature of the latter, presenting a contrast to the low mound of the former. During the Early Silla phase, two types of wooden chamber tombs with stone mounds were constructed at Wolseong North Burial Ground: those with burial chambers located above ground and those with subterranean burial chambers. Also constructed during this phase were the wooden chamber tomb embellished with packed stones, the wooden chamber tomb embellished with packed clay, simple earth cut burials, which had been used since the Incipient Silla phase, as well as the stone-lined burials with vertical entrance which first appeared in the Early Silla phase. However, of these different types of burials, it was only the wooden chamber tomb with stone mound that was covered with a 'high mound.' Differentiation between the different tomb types can also be observed in terms of location, type of burial chamber used, construction method, and tomb size. It is therefore possible to surmise that stratification between the different tomb types, which first emerged in the Incipient Silla phase, became intensified during the Early Silla phase.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.428-432
• /
• 2010

A study on the forming characteristics of outer shell structure for thrust chamber nozzle extension has been performed. In order to identify anisotropy of cold rolled sheet metal, three types of tensile specimens according to the direction to the sheet rolling axis were prepared and tested, and Landford's values were obtained using the results and applied to structural analysis. Forming characteristics of the outer shell structure of the nozzle extension are investigated through manufacturing and forming of the full scale outer shell structures, and strain values obtained by the forming processes are compared to the numerical analysis results. The results obtained by this study will be utilized to design forming tools and processes for manufacturing other outer shell structures which have a bigger expansion area ratio.

• Journal of the Korean Vacuum Society
• /
• v.19 no.3
• /
• pp.190-198
• /
• 2010

Asymmetric model for plasma uniformity by Ar and $CF_4$ was modeled by the antenna structure, the diameter of chamber, and the distance between source and substrate for the development of plasma equipment for 450 mm wafer. The aspect ratio of chamber was divided by diameter, distance from substrate, and pumping port area. And we found the condition with the optimized plasma uniformity by changing the antenna structure. The drift diffusion and quasi-neutrality for simplification were used, and the ion energy function was activated for the surface recombination and etching reaction. The uniformity of plasma density on substrate surface was improved by being far of the distance between substrate wall and chamber wall, and substrate and plasma source. And when the antenna of only 2 turns was used, the plasma uniformity can improve from 20~30% to 4.7%.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.2
• /
• pp.227-233
• /
• 2001

Electromagnetic field characteristics of Reverberation chamber, which could be applicable for an alternative test facility of electromagnetic interference and radiated electromagnetic susceptibility have been investigated. To obtain the required field uniformity of reverberation chamber, Schroeder method Quadratic Residue Diffuser was designed to be applied to chamber. In this paper, 3 different types of diffusers depending on diffuser's periodic direction have been used to investigate field characteristics of each type by using FDTD numerical method. The results show all 3 types of reverberation chambers have below $\pm$3 dB tolerance of field uniformity characteristics, and the symmetrical, type 3, structure show better results among them.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.4
• /
• pp.373-378
• /
• 2002

This paper presents the results of an electromagnetic field uniformity of a triangular reverberation chamber that can be used alternatively for analysis and measurement of electromagnetic interference and immunity test. Equilateral triangular reverberation chamber and Schroeder diffusers were designed and fabricated for this purpose. FDTD simulation method was applied to analyze the field distribution inside of two different types of reverberation chambers. As a result, the electromagnetic field uniformity was improved inside of triangular reverberation chambers, and the measured field uniformity was improved by 1 ∼4 ㏈ compared to the ones without diffusers.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.3
• /
• pp.206-211
• /
• 2005

The device makers want to make higher density chips on the wafer through scale-down. The change of WSix/poly-Si gate film thickness is one of the key issues under 100 nm device structure. As a new device etching process is applied, end point detection(EPD) time delay was occurred in DPS+ poly chamber of Applied Materials. This is a barrier of device shrink because EPD time delay made physical damage on the surface of gate oxide. To investigate the EPD time delay, the experimental test combined with OES(Optical Emission Spectroscopy) and SEM(Scanning Electron Microscopy) was performed using patterned wafers. As a result, a EPD delay time is reduced by a new chamber seasoning and a new wavelength line through plasma scan. Applying a new wavelength of 252 nm makes it successful to call corrected EPD in WSix/poly-Si stack-down gate etching in the DPS+ poly chamber for the current and next generation devices.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2006.11a
• /
• pp.465-468
• /
• 2006

The wave power absorbing performance of a bottom-mounted oscillating water column (OWC) chamber structure is studied. The potential problem inside the chamber is solved by making use of the Green integral equation associated with the Rankine Green function while the outer problem with the Kelvin Green function taking account of fluctuating air pressure in the air chamber. The absorbed wave power, wave elevation inside the chamber, reflection coefficient and wave loads are calculated for various values of a parameter related to the fluctuating air pressure. The present methods can also be used for the design of a OWC breakwater which can absorb and reflect the incoming wave energy at the same time.

• Journal of Navigation and Port Research
• /
• v.36 no.9
• /
• pp.729-735
• /
• 2012

The primary wave energy conversion by a three-dimensional bottom-mounted oscillating water column (OWC) wave power device in regular waves has been studied. The linear potential boundary value problem has been solved following the boundary matching method. The optimum shape parameters such as the chamber length and the depth of the front skirt of the OWC chamber obtained through two-dimensional numerical tests in the frequency domain have been applied in the design of the present OWC chamber. Time-mean wave power converted by the OWC device and the time-mean second-order wave forces on the OWC chamber structure have been presented for different wave incidence angles in the frequency-domain. It has been shown that the peak period of $P_m$ for the optimum damping parameter coincides with the peak period of the time.mean wave drift force when ${\gamma}=0$.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.3
• /
• pp.137-146
• /
• 1997

Spray characteristics of high pressure injectors for diesel engines have been experimentally studied with special emphasis on the effect of swirl. A constant volume chamber was rotated in order to generate a continuous swirl having the flow field of a solid body rotation, resulting in the linear dependance of the swirl number on the rotating speed of the chamber. Emulsified fuel is injected into the chamber and the developing process of fuel sprays is visualized. The fuel spray developing process in D.I. diesel engine was investigated by this liquid injection technique. The effect of swirl on the spray tip penetration is quantified through modelling. Results show that the spray tip penetration is qualitatively different for low and high pressure injections. For high pressure injection case, a good agreement is achieved between the experimental results and the modeling accounting the effect of swirl. For low pressure injection, a reasonable agreement is obtained. It is found that excessive swirl may cause adverse effect on spray dispersion during the initial combustion period since the spray can not be impinged on chamber wall.

• Korean Journal of Materials Research
• /
• v.20 no.7
• /
• pp.374-378
• /
• 2010

$MgTiO_3$ thin films were prepared by r.f. magnetron sputtering in order to prepare miniaturized NPO type MLCCs. $MgTiO_3$ films showed a polycrystalline structure of ilmenite characterized by the appearance of (110) and (202) peaks. The intensity of the peaks decreased with an increase in the chamber pressure due to the decrease of crystallinity which resulted from the decrease of kinetic energy of the sputtered atoms. The films annealed at $600^{\circ}C$ for 60min. showed a fine grained microstructure without micro-cracks. The grain size and roughness of the $MgTiO_3$ films decreased with the increase of chamber pressure. The average surface roughness was 1.425~0.313 nm for $MgTiO_3$ films prepared at 10~70 mTorr. $MgTiO_3$ films showed a dielectric constant of 17~19.7 and a dissipation factor of 2.1~4.9% at 1MHz. The dielectric constant of the films is similar to that of bulk ceramics. The dielectric constant and the dissipation factor decreased with the increase of the chamber pressure due to the decrease of grain size and crystallinity. The leakage current density was $10^{-5}\sim10^{-7}A/cm^2$ at 200kV/cm and this value decreased with the increase of the chamber pressure. The small grain size and smooth surface microstructure of the films deposited at high chamber pressure resulted in a low leakage current density. $MgTiO_3$ films showed a near zero temperature coefficient and satisfied the specifications for NPO type materials. The dielectric properties of the $MgTiO_3$ thin films prepared by sputtering suggest the feasibility of their application for MLCCs.