• Journal of the Korean Society of Industry Convergence
• /
• v.5 no.4
• /
• pp.385-390
• /
• 2002

An efficient synthesis of spiroannulated dihydrofurans is achieved from 1,3-dicarbonyl compounds and exocyclic alkenes in the presence of cerium ammonium nitrate(IV) in moderate yields. In the case of entries 3-9, as a single product was seen. Especially, reaction of 15 with methylenecyclohexane afforded the two regioisomeric cyclo adducts 21 and 22. The structures of these adducts were confirmed by IR and NMR-Spectra.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.9
• /
• pp.803-809
• /
• 2005

Cerium ammonium nitrate (CAN) and nitric acid was used an etchant and an additive for Ru etching and polishing. pH and Eh values of the CAN and nitric acid added chemical solution satisfied the Ru etching condition. The etch rate increased linearly as the concentration of CAN increased. Nitric acid added solution had the high etch rate. But micro roughness of etched surfaces was not changed before and after etching, The removal rate of Ru film was the highest in $1wt\%$ abrasive added slurry, and not increased despite the concentration of alumina abrasive increased to $5wt\%$. Even Ru film was polished by only CAN solution due to the friction. The highest removal rate of 120nm/min was obtained in 1 M nitric acid and $1wt\%$ alumina abrasive particles added slurry. The lowest micro roughness value was observed in this slurry after polishing. From the XPS analysis of etched Ru surface, oxide layer was founded on the etched Ru surface. Therefore, Ru was polished by chemical etching of CAN solution and oxide layer abrasion by abrasive particles. From the result of removal rate without abrasive particle, the etching of CAN solution is more dominant to the Ru CMP.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.05a
• /
• pp.257-257
• /
• 2012

Cerium doped anatase titania powders were prepared by sol-gel process, with ammonium (IV) nitrate and Titanium (IV) butoxide as the raw materials. The characteristics of anatase $TiO_2$ and cerium doped $TiO_2$ were investigated by XRD, DTA, FE-SEM and UV/Vis spectroscopy. Research results indicated that XRD data characteristic diffraction peaks of anatase phase and also showed that cerium phase was not observed. Moreover XRD and DTA results imply that the addition of cerium to titania modifies the mechanism of formation of the titania phases.

• Korean Journal of Materials Research
• /
• v.24 no.1
• /
• pp.33-36
• /
• 2014

This study was aimed at synthesizing and characterizing cerium-doped titania. Cerium-doped anatase titania powders were prepared by sol-gel process, with ammonium (IV) nitrate and titanium (IV) butoxide as the raw materials. The characteristics of pure $TiO_2$ and cerium-doped $TiO_2$ were investigated by XRD, TG/DTA, FE-SEM, and UV-vis spectroscopy. The results of this study show that anatase type of $TiO_2$ was obtained in as-prepared and calcined $TiO_2$ and Ce-$TiO_2$ powder. A DTA curve was also observed as the crystallization temperature decreased with increasing cerium contents. We found that the crystallite size of the obtained anatase particles decreased from 55 nm to 25 nm and the particle size decreased with increasing cerium contents. Moreover, UV-vis spectra showed that anatase titania powders with various cerium contents effectively extend the light absorption properties to the visible region.

• Corrosion Science and Technology
• /
• v.6 no.6
• /
• pp.304-307
• /
• 2007

As to the reflection electrode of LCD (liquid crystal displays), silver-copper-gold alloy (hereafter, it is called as ACA (Ag98%, Cu1%, Au1%)) is an effective material of which weathering resistance can be improved more compared with pure silver. However, there is a problem that gold remains on the substrate as residues when ACA is etched in cerium ammonium nitrate solution or phosphoric acid. Gold can not be etched in these etchants as readily as the other two alloying elements. Gold residue has actually been removed physically by brushing etc. This procedure causes damage to the display elements. Another etchant of iodine/potassium iodide generally known as one of the gold etchants can not give precise etch pattern because of remarkable difference in etching rates among silver, copper and gold. The purpose of this research is to obtain a practical etchant for ACA alloy. The results are as follows. The cyanogen complex salt of gold generates when cyanide is used as the etchant, in which gold dissolves considerably. Oxygen reduction is important as the cathodic reaction in the dissolution of gold. A new etchant of sodium cyanide / potassium ferricyanide whose cathodic reduction is stronger than oxygen, can give precise etch patterns in ACA alloy swiftly at room temperature.

• Journal of the Korean Chemical Society
• /
• v.20 no.4
• /
• pp.299-308
• /
• 1976

Cerium (Ⅳ) ion-initiated graft copolymerizations of acrylamide and of acrylonitirile to silk fibroins were investigated. When acrylamide was used, the change in ceric ammonium nitrate concentration exhibited a maximum in degree of grafting at 0.01 M. Also observed was that the change in acetic acid content in reaction media gave a maximum in degree of grafting at 7% acetic acid in water. Degree of grafting was increased generally with increase in acrylamide concentration reaction time and reaction temperature. When acrylonitrile monomer was used for grafting,different results were obtained. Addition of nitric acid was more effective in enhancing the degree of grafting than the addition of acetic acid.Generally the grafting of acrylonitrile to silk fibroins was less efficient than the grafting of acrylamide. The portion of grafted silk fibroins insoluble in Lowe's reagent exhibited the IR absorption bands characteristics to both vinyl polymers and silk fibroins, indicating the grafting of vinyl monomers to silk fibroins. To examine the molecular weight of graft vinyl polymer, a sample of grafted silk was hydrolyzed by 10% sodium hydroxide. Viscosity measurements indicated that the molecular weight of the graft polymer was in the range of 105.

• Journal of the Korean Society of Industry Convergence
• /
• v.6 no.2
• /
• pp.123-129
• /
• 2003

Oxindoles(6a-g) are obtained by rhodium(II)-catalyzed Wolff rearrangement of diazoquinolinediones in moderate yields. Treatment of 6a-g oxindole derivatives reacted with CAN in acetonitrile at room temperature to gave 7a-g isatins in good yields. The structures of these compound were identified by MP, IR and NMR-spectra.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.11a
• /
• pp.656-659
• /
• 2005

Nanocrystalline ceria powders were prepared by hydrothermal treatment of cerium(IV) ammonium nitrate solution without a precipitating agent. A systematic investigation of the effect of hydrothermal temperature and react ion time on the physical properties of the product powders was carried out. When the hydrothermal temperature was increased, the product ceria powders exhibited larger crystallite size with higher yield. Increasing reaction time produced more crystalline ceria powders attributed to further hydrothermal reactions and structural rearrangement. The physical properties of ceria powders can be control led by adjusting the hydrothermal conditions.

• Archives of Pharmacal Research
• /
• v.19 no.3
• /
• pp.240-242
• /
• 1996

We have reported the convenient biomimetic methodology for the synthesis of all kinds of substituent pattern benzo[c]phenanthridine alkaloids (Hanaoka et al., 1990; Hanaoka et al., 1991). Regioselective demethylation of C-8 position on oxyfagaridine (5), an intermediate for the synthesis of Fagaridine (4), would afford the precursor for the synthesis of Isofagaridine because the strong hydrogen bonding between amide and hydroxyl group of C-7 position probably resists to be reacted with week base and electrophiles. Thus, a selective alkylation of dihydroxy compound supposed to be possible and be lead to the target compound, Isofagaridine.

• Journal of Sericultural and Entomological Science
• /
• v.20 no.2
• /
• pp.40-44
• /
• 1978

Cerium (IV) ion-initiated graft copolymerizations of acrylonitrile to raw silk were investigated in an effort to carry out sericine-fixation. The change in ceric ammonium nitrate concentration exhibited a maximum in percentage of grafting at 0.003M. Also observed was that the change in nitric acid content in reaction media gave a maximum in percentage of grafting at 0.1M. Percentage of grafting was increased generally with increase in acrylonitrile concentration, reaction time and reaction temperature. Raw silk sericin grafted with acrylonitrile was not de gummed by boiling off test and optimum graft percentage was considered at 20%.