• Journal of the Korean Society of Safety
• /
• v.23 no.5
• /
• pp.7-14
• /
• 2008

The temperature distribution in a surface of diesel particulate filter(DPF) was measured using an infrared temperature camera. In order to regenerate the DPF, five partitioned electric heaters were used for heating the ceramic filter. The five partitioned heaters were switched on/off with some time interval one the other. The surface temperature distribution in the ceramic filter and electric heaters were measured with varying both the electrical power supply to the heaters and the mass flow rate of the air supply from a blower. The higher mass flow rate in the DPF system enhanced the uniformity in the surface temperature distribution of the ceramic filter due to effective convection heat transfer. The flow in the monolith ceramic structure of the DPF move mainly in the axial direction, which could be identified from the surface temperature of the ceramic filter.

• Applied Chemistry for Engineering
• /
• v.29 no.1
• /
• pp.18-21
• /
• 2018

We report on the simple preparation method of large-scale structured catalysts by temperature-regulated chemical vapor deposition with a high cell-density ceramic honeycomb monolith. And the feasibility for dry reforming of methane catalysts was evaluated. The NiO/Cordierite (CDR) catalyst was prepared by controlling coating conditions at each temperature step, leading to a conformal deposition of NiO inside the cordierite honeycomb monolith with the cell density of 600 cpsi. The catalytic conversion of $CH_4$ and $CO_2$ for dry reforming of methane were about 83% and 90% with gas hourly space velocity of $10,000h^{-1}$ at $800^{\circ}C$, respectively. As a result, it exhibited that the temperature-regulated chemical vapor deposition method can be expedient for the preparation of large-scale structured catalysts.

• Journal of the Korean Ceramic Society
• /
• v.44 no.4 s.299
• /
• pp.208-213
• /
• 2007

Alumina/silver ($Al_2O_3/Ag$) nanocomposites with Ag content up to 9 vol% were prepared from nanopowder by soaking method using ${\gamma}-Al_2O_3$ of needle type and spark plasma sintering (SPS). The mechanical properties of specimens were investigated three-point flexural strength and toughness as a function of the Ag contents. The maximum flexural strength of the alumina/silver nanocomposite was 850 MPa for the 1 vol% composite, and also higher than monolith alumina as about 800 MPa at 3, 5, and 7 vol% Ag contents. Fracture toughness by single edged V-notch beam (SEVNB) was $4.05MPa{\cdot}m^{1/2}$ for the 3 vol% composite and maintained about $4.00MPa{\cdot}m^{1/2}$ at 5, and 7 vol% Ag content. Microstructure of fracture surface for each fracture specimens was observed. Due to the inhibition effect of alumina grain growth, the average grain size of nanocomposites depends on the content of Ag nano particles. The fracture morphology of nanocomposite with dislocation (sub-grain boundary) by silver nano-particles of second phases in the alumina matrix also showed transgranular fracture-mode compare with intergranular of monolith alumina. Thermal conductivity of specimens at room temperature was about 40 W/mK for the 1 vol% Ag content.

• Journal of the Korean Ceramic Society
• /
• v.50 no.6
• /
• pp.359-363
• /
• 2013

Silicon carbide and its composites are being considered as a nuclear fuel cladding material for LWR nuclear reactors because they have a low neutron absorption cross section, low hydrogen production under accident conditions, and high strength at high temperatures. The SiC composite cladding tube considered in this study consists of three layers, monolith CVD SiC - $SiC_f$/SiC composite -monolith CVD SiC. The volume fraction of SiC fiber and surface roughness of the composite layer affect mechanical and corrosion properties of the cladding tube. In this study, various types of SiC fiber preforms with tubular shapes were fabricated by a filament winding method using two types of Tyranno SA3 grade SiC fibers with 800 filaments/yarn and 1600 filaments/yarn. After chemical vapor infiltration of the SiC matrix, the surface roughness and fiber volume fraction were measured. As filament counts were changed from 800 to 1600, the surface roughness increased but the fiber volume fraction decreased. The $SiC_f$/SiC composite with a bamboo-like winding pattern has a smaller surface roughness and a higher fiber volume fraction than that with a zigzag winding pattern.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.21 no.5
• /
• pp.282-290
• /
• 2009

A ceramic monolith heat exchanger is studied to find the performance of heat transfer and pressure drop by numerical computation and $\xi$-NTU method. The numerical computation was performed throughout the domain including fluid region in exhaust gas-side rectangular ducts, ceramic core and fluid region in air-side rectangular duct with the air and exhaust in cross flow direction. In addition, the heat exchanger was also analyzed to estimate the performance by conventional $\xi$-NTU method with several Nusselt number correlations for flow in rectangular duct from literature. By comparisons of both performances by the numerical computation and the $\xi$-NTU method, the effectiveness by $\xi$-NTU method was closest to the result by numerical computation within a relative error of 2.14% when Stephan's Nusselt number correlation was adopted to the $\xi$-NTU method among the several correlations.

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.60-66
• /
• 1992

This study describes a theoretical analysis for the wall temperature of ceramic filter trap and pressures of inlet and outlet channel in the filter trap. In this study, the maximum wall temperature through filter trap length with time during the regeneration period showed a tendency moving from forward to backward. The pressure change of filter trap increased at the initial combustion but decreased with the combustion to be activated. So the pressure difference between initial and end regeneration at the inlet channel showed about 2kPa. The thermal regeneration period of this filter trap in the theoretical analysis showed about 200seconds in which the wall temperature was similar to the case of initial condition and the pressure showed about 1 kPa.

• Journal of the Korean Ceramic Society
• /
• v.30 no.3
• /
• pp.243-249
• /
• 1993

Coated type Al2O3-SiC composite powders were synthesized by surface modification method. Transformation temperature to $\alpha$-Al2O3 of Al2O3 monolith was 115$0^{\circ}C$ whereas increased to 1200, 1250, 130$0^{\circ}C$ with increment of SiC content to 5, 15, 25wt%. Transformation temperature to $\alpha$-Al2O3 was lowered by $\alpha$-Al2O3 seeding. FTIR data analysis and electron micrographs showed that Al2O3 particles were effectively coated on SiC particles.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11b
• /
• pp.152-155
• /
• 2005

Diesel particulate filter (DPF) is comprised of a number of capillary tubes enclosed by porous ceramic wails, shaped like a plugged duct. Hot gas flows through the DPF along with the exhaust noise from Diesel engine. Based on previous works on the sound propagation through DPF, in this study, losses at entrance, exit, and ceramic walls are considered and the gradients in temperature and flow velocity are considered. Transfer matrix at entrance, monolith, and exit parts are obtained by employing the segmental approach in analyzing the sound propagation through DPF. The predicted transmission loss agrees very well with the empirical one, which is measured by the improved method with correction terms.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.1
• /
• pp.1-13
• /
• 1997

The key point that guarantees the durability of the ceramic monolith filter is to lower peak temperature and temperature gradient inside filter during regeneration. The control of the exhaust gas flow rate into the filter, by the bypass technique of the exhaust gas, enables the gas temperature in filter to be constant for regeneration. A couple of methods, which are the ON/OFF and PID control of the bypass valve, were used for feedback control of the gas temperature. These techniques showed that the ceramic filter was regenerated perfectly under the peak temperature and peak temperature gradient limitations for durability.

• Journal of the Korean Ceramic Society
• /
• v.31 no.9
• /
• pp.1021-1029
• /
• 1994

SiC ultrafine particles of 1, 10, 20 and 30 vol% were dispersed in $\alpha$-Si3N4 matrix and hot-pressed under the condition of 30 MPa at 1800 and 190$0^{\circ}C$ respectively. Physical, mechanical properties and microstructures of sintered Si3N4-SiC nanocomposites were investigated. Flexural strength and density of Si3N4-10 vol% SiC nanocomposites hot-pressed at 190$0^{\circ}C$ represented the 1002 MPa and 97.9%T.D respectively, and it was confirmed as a remarkable improvement of 67% compared to Si3N4 monolith. Fracture toughness was shown as 7.2 MPa.m1/2 when the same composition was hot pressed at 180$0^{\circ}C$. This effect was supposed to be due to the improvement of microstructure by the adequate suppression of the excessive growth of Si3N4 grain with SiC nano-particles.