• 한국세라믹학회지
• /
• 제35권12호
• /
• pp.1343-1350
• /
• 1998

A study is made of mechanical properties of unglazed matrix as a funtion of sintering temperature and crack patterns in layer structur pottery consisting of glaze and substrate and in matrix which is sintered at 120$0^{\circ}C$ and 130$0^{\circ}C$ respectively. The mechanical properties of matrix are increased due to density and vitrification to 130$0^{\circ}C$ The interface of glazed bilayer reveals the reactive intermediate layer. Herzian indentation testing is used to investigate the evolution of damage modes as a function of load. In the materials sintered at 120$0^{\circ}C$ quasi-plastic deformation is developed at the matrix and the cone-like cracks initiate at the glazing top surface and additionally upward-extending transverse cracks initiate at the internal in-just initiate at the glazing top surface which pass through the interface with increasing of indentation load. Finally the dominant damage mode shifts from substrate quasi-plasticity to coating fracture with increasing sintering temperature.

• 한국세라믹학회지
• /
• 제28권12호
• /
• pp.1012-1018
• /
• 1991

SiC whisker-reinforced LAS matrix composites were developed by a mixed colloidal processing route. An optimization of processing conditions was made using the zeta potential data of silica, boehmite, and SiC whisker dispersions. Similarly, the SiC whisker-reinforced composites were also fabricated by the conventional sol-gel process using the hydrolysis-condensation reaction of relevant metal alkoxides. The composites fabricated by the mixed colloidal processing route were characterized by a uniform spatial distribution of SiC whisker throughout the matrix. The fracture toughness increased from 1.3 MPa.m1/2 for the LAS specimen to 5.0 Mpa.m1/2 for the hot-pressed composite (95$0^{\circ}C$ and 20 MPa for 20 min) containing 20 wt% SiC whisker. The increase in fracture toughness appears to result mainly from the crack deflection and the crack bridging by whiskers with some additional toughenings from the whisker pullout and the matrix prestressing mechanisms.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.921.1-921.1
• /
• 2006

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제1권1호
• /
• pp.17-33
• /
• 2001

The characteristics of Weibull distribution are investigated as a function of shape parameter. The statistical estimation methods of the shape parameter and statistical comparison methods of two or more shape parameters are studied. Assuming Weibull distribution, statistical analysis of bending-strength data of alumina titanium carbide ceramic matrix composites machined two different methods are performed.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.5-13
• /
• 2006

Based on the inventions of continuous ceramic fibers, such as C, SiC, $Al_2O_3$ etc., by polymer precursor driven methods, there have been many efforts to fabricate ceramic continuous fiber reinforced composite materials with metals and ceramics matrices. The main purpose of the R & D efforts has been to produce materials for severe environments, including advanced energy systems, advanced transportation systems. The efforts have been started from the R & D of metal matrix composite materials and now the strong emphasis on ceramic matrix composites R & D can be recognized. This paper provides a brief review about the national efforts to establish advanced composite materials for future industries starting from mid 70s. C/Al and SiC/Al are the typical examples to be applied transportation systems and energy systems. The excellences in specific strength and overall mechanical properties, the excellences in environmental resistance make those materials as potential materials for advanced ocean construction and marine transportation systems. About the recent progress in ceramic fiber reinforced ceramic composites, advanced SiC/SiC composites including NITE-SiC/SiC will be introduced and the present status will be introduced.

• 한국재료학회지
• /
• 제34권3호
• /
• pp.175-183
• /
• 2024

Geopolymer, also known as alkali aluminum silicate, is used as a substitute for Portland cement, and it is also used as a binder because of its good adhesive properties and heat resistance. Since Davidovits developed Geopolymer matrix composites (GMCs) based on the binder properties of geopolymer, they have been utilized as flame exhaust ducts and aircraft fire protection materials. Geopolymer structures are formed through hydrolysis and dehydration reactions, and their physical properties can be influenced by reaction conditions such as concentration, reaction time, and temperature. The aim of this study is to examine the effects of silica size and aging time on the mechanical properties of composites. Commercial water glass and kaolin were used to synthesize geopolymers, and two types of silica powder were added to increase the silicon content. Using carbon fiber mats, a fiber-reinforced composite material was fabricated using the hand lay-up method. Spectroscopy was used to confirm polymerization, aging effects, and heat treatment, and composite materials were used to measure flexural strength. As a result, it was confirmed that the longer time aging and use of nano-sized silica particles were helpful in improving the mechanical properties of the geopolymer matrix composite.

• 한국세라믹학회지
• /
• 제31권4호
• /
• pp.375-380
• /
• 1994

Matrices retaining electrolyte in phosphoric acid fuel cell were prepared with SiC to SiC whisker mixing ratios of 1:0.5, 1:1, 1:1.5, 1:2, 1:3 by tape casting method. When viscosity of the slurry was 5.9 poise and the SiC to SiC whisker mixing ratios were 1:1, 1:1.5, 1:2, the ranges of porosity, acid absorbency and bubble pressure were 80~90%, 2.5~6 and 700~2200 mmH2O, respectively. Those ranges are acceptable for a practical electrolyte-retaining matrix. With increasing the mixing ratio of SiC whisker to SiC, the porosity and the vol.% of large pores in the main pore size distribution which is between 1 and 10 ${\mu}{\textrm}{m}$, increased rapidly. Impedance spectroscopy was measured to know characteristics of matrix inside and contact region of matrix to catalyst layer. When the SiC to SiC whisker mixing ratio was 1:2, hydrogen ions were transported in the matrix most effectively because of high ionic conductivity and low activation energy due to high acid absorbency in spite of high interfacial resistance. The cell current density of the cell made using the matrix was 220 mA/$\textrm{cm}^2$ at 0.7 V.

• 한국분말재료학회지
• /
• 제29권5호
• /
• pp.424-431
• /
• 2022

3Y-TZP ceramics obtained by doping 3 mol.% of Y₂O₃ to ZrO₂ to stabilize the phase transition are widely used in the engineering ceramic industry due to their excellent mechanical properties such as high strength, fracture toughness, and wear resistance. An additional increase in mechanical properties is possible by manufacturing a composite in which a high-hardness material such as oxide or carbide is added to the 3Y-TZP matrix. In this study, composite powder was prepared by dispersing a designated percentage of WC in the 3Y-TZP matrix, and the results were compared after manufacturing the composite using the different processes of spark plasma sintering and HP. The difference between the densification behavior and porosity with the process mechanism was investigated. The correlation between the process conditions and phase formation was examined based on the crystalline phase formation behavior. Changes to the microstructure according to the process conditions were compared using field-emission scanning electron microscopy. The toughness-strengthening mechanism of the composite with densification and phase formation was also investigated.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.134-134
• /
• 2016

CMC(Ceramic Matrix Composites)는 $1500^{\circ}C$ 이상의 고온에서 내열성, 내산화성, 내식성이 우수하여, 초음속 비행체, 가스터빈 엔진 및 원자로용 초고온 부품 등에 수요가 증가하고 있다. 하지만 이러한 특성은 비산소 환경에 국한되는 것으로 약 $400^{\circ}C$ 이상의 산화 분위기에는 탄소섬유가 산화되는 문제로 인하여 적용의 한계를 가지고 있다. 따라서 CMC의 적용범위 확대를 위하여 내산화 코팅으로 CMC의 초고온 산화특성을 개선하는 것이 필수적이며, 장시간 초고온 산화환경 분위기에서 사용되기 위하여 안정적인 코팅기술이 최근 기술개발의 핵심현안으로 부각되고 있다. 본 연구에서는 pack cementation 공정을 이용하여 내산화성이 우수한 SiC 코팅층을 제조하였다. Pack cementation 공정에 사용된 코팅 분말은 57wt.% SiC, 30wt.% Si, 3wt.% B, 10wt.% Al2O3의 비율로 혼합된 것이다. 실험은 3D 직조된 CMC 모재를 혼합분말 내에 침적한 후, Ar 분위기에서 $1600^{\circ}C$, 4~12시간 반응시켜 수 마이크론 두께의 SiC 코팅층을 형성하였다. 더 우수한 산화 특성을 부여하기 위하여 pack 처리된 CMC 표면에 초고온 세라믹인 TaC 소재를 진공플라즈마 코팅 공정으로 적층시켰다. 제조된 코팅층을 SEM, XRD를 이용하여 미세구조 및 결정구조를 분석하였으며, pack cementation에 따른 내산화 특성을 비교 분석하고자 $2000^{\circ}C$에서 산화 실험을 진행하였다. 산화 실험 이후 미세구조 및 결정구조 분석으로 산화거동을 규명하고자 하였다.

• Nuclear Engineering and Technology
• /
• 제48권3호
• /
• pp.650-659
• /
• 2016

As a type of accident-tolerant fuel, fully ceramic microencapsulated (FCM) fuel was proposed after the Fukushima accident in Japan. The FCM fuel consists of tristructural isotropic particles randomly dispersed in a silicon carbide (SiC) matrix. For a fuel element with such high heterogeneity, we have proposed a two-temperature homogenized model using the particle transport Monte Carlo method for the heat conduction problem. This model distinguishes between fuel-kernel and SiC matrix temperatures. Moreover, the obtained temperature profiles are more realistic than those of other models. In Part I of the paper, homogenized parameters for the FCM fuel in which tristructural isotropic particles are randomly dispersed in the fine lattice stochastic structure are obtained by (1) matching steady-state analytic solutions of the model with the results of particle transport Monte Carlo method for heat conduction problems, and (2) preserving total enthalpies in fuel kernels and SiC matrix. The homogenized parameters have two desirable properties: (1) they are insensitive to boundary conditions such as coolant bulk temperatures and thickness of cladding, and (2) they are independent of operating power density. By performing the Monte Carlo calculations with the temperature-dependent thermal properties of the constituent materials of the FCM fuel, temperature-dependent homogenized parameters are obtained.