• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.11
• /
• pp.33-41
• /
• 2014

This paper is research result for a development of sapphire silicon ingot glowing(SSIG) PWM converter system for 80kW 10kA. The system include 3-phase AC-DC diode rectifier of input voltage AC 380V and 60Hz, DC-AC single phase full bridge PWM inverter of high frequency, AC-DC single-phase full wave rectifier using center-tapped of transformer for low voltage 8.0V and large current 10,000A of output specification, tungsten resistor load 0.1[$m{\Omega}$]. PWM switching frequency for IGBT inverter control set 30kHz. The suggested researching contents are designed data sheets of power converter system, PSIM simulation, operating characteristics and analysis results of developed SSIG system. This paper propose

• 전기의세계
• /
• v.13 no.4
• /
• pp.25-29
• /
• 1964

This paper shows that higher amplification can be achieved by applying load current on the internal feedback winding of the magnetic amplifier under test. Since the magnetic flux of the control winding and internal feedback winding saturate the core more fully, the permeability tends to zero and load current increases to the value more than that of ordinary magnetic amplifier without feedback.

• Journal of Power Electronics
• /
• v.8 no.3
• /
• pp.217-227
• /
• 2008

The electric power subsystems (EPS) of most remote sensing satellites consist of a solar array as a source of energy, a storage battery, a power management and control (PMC) unit and a charge equalization unit (CEU) for the storage battery. The PMC and CEU use high frequency transformers in their power modules. This paper presents a design, implementation and testing results of a high frequency transformer for the EPS of satellite applications. Two approaches are used in the design process of the transformer based on the pre-determined transformer specifications. The transformer is designed based on an ETD 29 ferrite core. The implemented transformer consists of one center-tapped primary coil with eleven center-tapped secondary coils. The offline calculation results and measured values of R, L for transformer coils are convergence. A test circuit for measuring the transformer parameters like voltage, current and B-H hysteresis was implemented and applied. The test results confirm that the voltage waveforms of both primary and secondary coils were as desired. No overlapping occurred between the control signal and the transformer, which was not saturated during testing even during a short circuit test of the secondary channels. The dynamic B-H loop characteristics of the used transformer cores were measured. The sample test results are given in this paper.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.9 no.4
• /
• pp.22-31
• /
• 2010

In this paper, a new split ring resonator using left-handed meta-material adapted in a bandpass filter with 2-stages is suggested. In this proposed bandpass filter, the size of the novel resonator can be easily controlled. Also, the bandwidth can be adjusted with the position of the tapped-line. The proposed resonator and filter has the center frequency of 10 GHz for I-band in military-satellite communication system with the Qe value of 184. The experimental results of the filter show that the insertion and return losses are 1.43 dB and 16.8 dB with bandwidth of 10 %, respectively.

• Proceedings of the KIPE Conference
• /
• 2013.11a
• /
• pp.214-215
• /
• 2013

본 논문에서는 LED조명용 다중 부하를 동시에 구동하기 위한 강압 또는 승압용 컨버터를 대신하여, 장 수명에 유리하며 다채널 정전류 제어가 가능한 중간 탭 공진 변압기를 이용한 LED조명 드라이버를 설계하고 실험으로 검증하였다.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.317-320
• /
• 2000

This paper proposes a voltage compensation method to improve the control performance of B4 inverter which is studied for low-cost drive systems. The B4 inverter employs only four switches and it has a center-tapped connection in the split dc-link capacitors to one phase of a three-phase motor. In the B4 topology unbalan-cd three-phase voltages will be generated by the dc link voltage ripple. To solve this problem we present a voltage compensation method which adjusts switching times considering dc link voltage ripple. The proposed method is verified by simulation results,

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.2 no.4
• /
• pp.10-16
• /
• 1991

A microstrip bandpass filter using stepped impedance resonators and tapped input / output is realized with Teflon substrate, whose center frequency is 3.5 GHz and fractional bandwidth is 20%. In order to realize a wider bandwidth of 30%, the Crystal's design method and the input / output tapping scheme are used. Another microstrip filter designed as mentioned above is realized with Epsilam-10 substrate. This case shows good agreement between the theoretical responses and the measured ones.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.161-162
• /
• 2011

높은 승압비를 위한 기존의 탭인덕터 부스트 컨버터는 스위치의 턴-온/오프 시 기생 소자의 공진에 의해 발생하는 스위치 및 다이오드의 큰 전압 스트레스를 해결하기 위해 손실 스너버를 적용하였고, 이로 인해 효율 저하 및 원가 상승의 문제점이 있었다. 본 논문에서는 이러한 문제점을 해결할 수 있는 고효율의 부스트 컨버터를 제안한다. 제안된 회로는 트랜스포머를 사용하여 높은 승압비를 달성하고, 각 소자의 내압을 링크전압 또는 출력전압으로 제한하여 고효율 저가격화 및 신뢰성 개선에 매우 유리하다. 최종적으로 제안회로의 입력 DC24V 및 출력 DC230V인 모의실험을 통해 고찰된 실험결과를 제시함으로써 제안 회로의 우수성과 이론적 분석의 타당성을 검증한다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.490-492
• /
• 2010

A swing level controlled voltage-mode transmitter is proposed to support a stub series-terminated logic channel with center-tapped termination. This transmitter provides a swing level control to support the diagnostic mode and improve the signal integrity in the absence of the destination termination. By using the variable parallel termination, the proposed transmitter maintains the constant output impedance of the source termination while the swing level is controlled. Also, the series termination using an external resistor is used to reduce the impedance mismatch effect due to the parasitic components of the capacitor and inductor. To verify the proposed transmitter, the voltage-mode driver, which provides eight swing levels with the constant output impedance of about $50{\Omega}$, was implemented using a 70nm 1-poly 3-metal DRAM process with a 1.5V supply. The jitter reduction of 54% was measured with the swing level controlled voltage-mode driver in the absence of the destination termination at 1.6-Gb/s.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.10 s.101
• /
• pp.1010-1019
• /
• 2005

In this paper, we used neural network technique to model memory effects of RF power amplifier which is fed by two-tone input signals. The memory effects in power amplifier were identified by observing the unsymmetrical distribution of IMD(Inter-Modulation Distortion) measurements with the change of tone spacings and power levels. Different asymmetries of IMD were also found at different center frequencies. We applied TDNN technique to model LDMOS power amplifier based on two tone IMD data, and the accuracy was very high compared to other modeling methods such as the(memoryless) adaptive modeling method.