• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.721-724
• /
• 2006

In this study, particle size distribution of cement powder system were adjusted using the blast furnace slag powder, Blaine $2250cm^2/g\;and\;8300cm^2/g$, which easy to adjust particle size distribution to examine how particle size distribution of the binder has an effect on rheological properties of the cement paste. In addition, the relationship between n-value of Rosin-Rammler function and plastic viscosity were discussed. All measured flow curves represented thixotropy behavior and the hysteresis area was smaller for the more added coarse particle. When the combination was based on a ratio of $20{\sim}25vol%$ fine particles, $30{\sim}40vol%$ OPC and $40{\sim}45vol%$ coarse particles of the total volume, a high fluidity and low yield strength was achieved.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.11a
• /
• pp.186-187
• /
• 2013

Recently, high fluidity concrete is becoming more prevalent. High fluidity concrete uses admixture or thickener in order to prevent separation of materials due to increased fluidity, and, especially, BS is becoming more use for reduced heat of hydration and improved long-term strength. This study examined the effect of BS on fluidity of cement paste from a rheological viewpoint. As for BS types, materials equivalent to 1 types of KS F 2563 and the cement mass was substituted by 20, 40, 60, 80%.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.11a
• /
• pp.23-24
• /
• 2019

In this paper, the compressive strength characteristics of cement paste were compared with the addition of liquefied red mud with the addition of nitric acid in order to improve the strength of the deteriorated cement. The results showed that the compressive strength with between 7 days and 28 days was greater than that of liquefied red mud. The ratio of daily compressive strength of the liquefied red mud is higher than that of the Plain with a 1 percent addition rate, and the ratio of compressive strength is lower than that of the Plain on the 28 days. Therefore, the compressive strength of neutralization liquefied red mud compared to liquidated red mud was relatively high, and the compressive strength of the red mud was shown to be improved to a level almost similar to that of Plain.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.06a
• /
• pp.33-34
• /
• 2020

Unit-water content is an element directly related to durability and unit-water content of concrete used at construction site has a great effect on the durability of construction structure. Many methods are being discussed for more convenient and accurate measurements of unit-water content. Therefore, an experimental study was conducted on the prediction of unit-water content using ultrasonic equipment. Depending on the amount of cement in cement paste, the speed of ultrasonic waves varies and the experiment will be carried out using the same reception sensitivity in the future.

• Computers and Concrete
• /
• v.15 no.6
• /
• pp.903-919
• /
• 2015

The flow of freshly mixed cement-based material shows thixotropy, which implies some difficulties on robust measurement of its rheological properties: The flow curve of thixotropic materials depends on the used protocol. For examples, higher viscosity is obtained when the rate of shear strain is more quickly increased. Even though precise measurement and modelling of the concrete rheology needs to consider the thixotropic effect, engineers in the concrete field prefer considering as a non-thixotropic Herschel-Bulkley fluid, even more simply Bingham fluid. That is due to robustness of the measurement and application in casting process. In the aspect of simplification, this papers attempts to mimic the thixoropic flow by the non-thixotropic Herschel-Bulkley model. Disregarding the thixotropy of cement based materials allows us to adopt the rheological concept in the field. An optimized protocol to measure the Bingham parameters was finally found based on the accuracy and reproducibility test of cement paste samples, which minimizes the error of simulation stemming from the assumption of non-thixotropy.

• Journal of the Korean Ceramic Society
• /
• v.52 no.1
• /
• pp.48-55
• /
• 2015

Hardened cement-based materials exposed to the high temperatures of a fire are known to experience change in the pore structure as well as microstructural changes that affect their mechanical properties and tend to reduce their durability. In this experimental investigation, hardened Portland cement pastes were exposed to elevated temperatures of 200, 400, 600, 800, and $1000^{\circ}C$ for 60 minutes, and the resulting damage was studied by thermogravimetry (TG), mercury intrusion porosimetry (MIP) and density measurements. These results revealed that the residual compressive strength is increased at temperatures greater than $400^{\circ}C$ due to a small pore size of 3 nm and/or rehydration of the dehydrated cement paste. However, a loss of the residual strength occurs at temperatures exceeding 500 and $600^{\circ}C$. This can be attributed to the decomposition of hydrates such as portlandite and to an increase in the total porosity.

• Advances in concrete construction
• /
• v.11 no.3
• /
• pp.183-192
• /
• 2021

Due to economic and environmental benefits, increasing the substitution ratio of ordinary cement by industry by-products like fly ash (FA) is one of the best approaches to reduce the impact of the concrete industry on the environment. However, as the substitution rate of FA increases, it will have an adverse impact on the performance of cement-based materials, so the actual substitution rate of FA is limited to around 10-30%. Therefore, in order to increase the early-age strength of high replacement (30-70%) low-calcium ultrafine FA blended cement paste, sodium sulfate and calcium sulfate dihydrate were used to improve the reactivity of FA. The results show that sodium sulfate has a significant enhancement effect on the strength of the composite pastes in the early and late ages, while calcium sulfate dihydrate has only a slight effect in the late ages. The addition of sodium sulfate in the cement-FA blended system can enhance the gain rate of non-evaporation water, and can decrease the Ca(OH)2 content. In addition, when the sulfate chemical activators are added, the ettringite content increases, and the surface of the FA is dissolved and hydrated.

• Journal of the Korea Concrete Institute
• /
• v.18 no.2 s.92
• /
• pp.213-218
• /
• 2006

Meniscus, adsorbed layer thickness, capillary pressure and disjoining pressure was deduced in extended meniscus region in cement paste pore by hydrostatic equilibrium. From the results, the relationship between pore size and adsorbed layer thickness could be derived and adsorbed layer thickness represents $0.299{\sim}2.700nm$ according to pore size $1nm{\sim}1{\mu}m$. Especially, disjoining pressure rapidly Increased in less than 10 nm pore size according to adsorbed layer thickness. Therefore, it is interpreted that autogenous shrinkage of cement paste is highly increases in formation of less than 10 nm pore size. Predictions of autogenous shrinkage in cement paste considering driving force for autogenous shrinkage with capillary pressure and disjoining pressure was low in comparison with experiment values between $1{\sim}4$ days and high in later period. These tendency could be thought that pore damage by mercury injection in early age makes shrinkage driving force underestimate and assumption for unsaturated independent pore makes overestimate. These interactions might be needed corrections considering on hydration or pore replacement model.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.5
• /
• pp.403-412
• /
• 2018

Recently, needs for utilization of recycled aggregate have been increasing. However, its utilization has been limited due to its high alkalinity, which mostly came from the unremoved cement paste particles that were attached at the surface of recycled aggregate. Various efforts has been made to reduce its alkalinity by using $CO_2$, but currently available methods that uses $CO_2$ generate the problem with pH recovery. Considering the fact that supercritical $CO_2$ ($scCO_2$) can provide more rapid carbonation of cement paste than by normal $CO_2$, $scCO_2$ was utilized in this work. The reaction between $scCO_2$ and hydrated cement paste has been systematically evaluated. According to the results, it was found that powder type showed higher carbonation compared to that of cube specimens. It seems the carbonation by $scCO_2$ has occurred only at the surface of the specimen, and therefore still showed some amount of $Ca(OH)_2$ calcium aluminates after reaction with $scCO_2$. With powder type specimen, all $Ca(OH)_2$ was converted into $CaCO_3$. Moreover, additional calcium that came from both calcium aluminate hydrates and calcium silicate hydrates reacted with $scCO_2$ to form $CaCO_3$. After carbonation with $scCO_2$, the powder type specimen did not show pH recovery, but cube specimens did show due to the presence of portlandite.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.9
• /
• pp.405-413
• /
• 2020

The normal stress of cement paste measured under squeeze flow is divided into an elastic solid region at strains between 0.0003 and 0.003 and a strain-hardening region at strains of 0.003 and 0.8. A modeling equation at the strain-hardening region was proposed. First, from the viewpoint of fluid behavior, the power-law non-Newtonian fluid model, with a power-law consistency (m) of 700 and a power index (n) of 0.2, was applied. The results showed good agreement with the experimental results except for an elastic solid region. Second, from the viewpoint of ductile yielding solid behavior, the force balance model was applied, and the friction coefficient between the sensor part measuring the load and the surface of the cement paste was derived as a polynomial of the normal strain by applying the half-interval search method to the experimental data. The results showed good agreement with the experimental results only in the middle normal strain region at strains between 0.003 and 0.3. The rheological behavior of the cement paste under squeeze flow was more consistent with the experimental results from the viewpoint of power-law non-Newtonian fluid behavior than from the viewpoint of ductile yielding solid behavior in the strain-hardening region.