• Macromolecular Research
• /
• v.14 no.4
• /
• pp.449-455
• /
• 2006

Ionic cluster mimic, polymer electrolyte membranes were prepared using polymer composites of crosslinked poly(vinyl alcohol) (PVA) with sulfated-${\beta}$-cyclodextrins (${\beta}-CDSO_3H$) or phosphated-${\beta}$-cyclodextrins (${\beta}-CDPO(OH)_2$). When Nafion, developed for a fuel cell using low temperature, polymer electrolyte membranes, is used in a direct methanol fuel cell, it has a methanol crossover problem. The ionic inverted micellar structure formed by micro-segregation in Nafion, known as ionic cluster, is distorted in methanol aqueous solution, resulting in the significant transport of methanol through the membrane. While the ionic structure formed by the ionic sites in either ${\beta}-CDSO_3H$ or ${\beta}-CDPO(OH)_2$ in this composite membrane is maintained in methanol solution, it is expected to reduce methanol transport. Proton conductivity was found to increase in PVA membranes upon addition of ionized cyclodextrins. Methanol permeability through the PVA composite membrane containing cyclodextrins was lower than that of Nafion. It is thus concluded that the structure and fixation of ionic clusters are significant barriers to methanol crossover in direct methanol fuel cells.

• Korean Membrane Journal
• /
• v.6 no.1
• /
• pp.44-54
• /
• 2004

Organic-inorganic composite membranes based on sulfonated poly(phthalazinone ether sulfone) (sPPES)/silica hybrid were prepared using the sol-gel process under acidic conditions. The sulfonation of PPES with concentrated sulfuric acid as sulfonation agent was carried out to prepare proton exchange membrane material. The behaviors of the proton conductivity and methanol permeability are depended on the sulfonation time (5-100 hr). The hybrid membranes composed of highly sulfonated PPES (IEC value: 1.42 meq./g) and silica were fabricated from different silica content (5-20 wt%) in order to achieve desirable proton conductivity and methanol permeability demanded for fuel cell applications. The silica particles within membranes were used for the purpose of blocking excessive methanol cross-over and for forming the path way to transport of the proton due to absorbing water molecules with ≡SiOH on silica. The presence of silica particles in the organic polymer matrix results in hybrid membranes with reduced methanol permeability and improved proton conductivity.

• Clean Technology
• /
• v.11 no.3
• /
• pp.141-146
• /
• 2005

The composite membranes were made by grafting using supercritical carbon dioxide (scCO2) impregnation and polymerization procedures. The membranes were synthesized by changing amount of monomer. The polypropylene grafted polystyrene sulfonic acid (PP-g-pssa) membranes were characterized with various methods. The morphology and structure of PP-g-pssa membranes were analyzed with scanning electron microscopy (SEM) and energy dispersive spectrometer (EDS). As amount of monomer was increased, ion conductivity, cell performance was increased and methanol permeability was decreased. However PP-g-pssa membranes with 1.5g monomer and over had similar values of methanol permeability, ion conductivity and cell performance.

• Membrane Journal
• /
• v.22 no.3
• /
• pp.191-200
• /
• 2012

New composite membranes were manufactured by impregnating post-sulfonated poly(arylene ether sulfone)s containing perfluorocyclobutane (PFCB) groups into porous polytetrafluoroethylene (PTFE) films. Two kinds of post-sulfonated poly(arylene ether sulfone)s with two different monomer ratios (sulfonable biphenylene monomer : non-sulfonable sulfonyl monomer = 6 : 4, 4 : 6) were first prepared through three synthetic steps: synthesis of trifluorovinylether-terminated monomers, thermal cycloaddition polymerization and post-sulfonation using chlorosulfonic acid (CSA). The composite membranes were then prepared by adjusting the concentrations (5~20 wt%) of the resulting copolymers impregnated in the PTFE films. The water uptake, ion exchange capacity (IEC) and ion conductivity of the composite membranes were characterized and compared with their unreinforced dense membranes and Nafion. All the synthesized compounds, monomers and polymers were characterized by $^1H$-NMR, $^{19}F$-NMR and FT-IR and the composite membranes were observed with scanning electron micrographs (SEM).

• Membrane Journal
• /
• v.33 no.6
• /
• pp.416-426
• /
• 2023

In this study, hindered amine-grafted graphene oxide (HA-GO) with antioxidant properties was prepared and incorporated into Nafion-based composite membranes as an effective filler material for polymer electrolyte membrane fuel cell applications. HA-GO was synthesized via a ring-opening reaction between amine groups in 4-amino-2, 2, 6, 6-tetramethyl piperidine and epoxy groups on the surface of GO. Nafion-based composite membranes containing different weight contents of HA-GO were fabricated to compare the polymer electrolyte membrane properties with those of the pure Nafion membrane. The composite membranes with HA-GO were found to have better mechanical properties, chemical stability, and proton conductivity than the pure Nafion membrane. In particular, the conductivity retention behavior confirmed by the decrease in proton conductivity after Fenton's test of the composite membranes was better than that of the pure Nafion membrane due to the incorporation of HA-GO with effective antioxidant properties.

• Membrane Journal
• /
• v.5 no.3
• /
• pp.109-118
• /
• 1995

In this study, cell resistivity and membrane resistivity were measured in Fe-Cr redox-fiow battery system using commercial ion-exchange membranes. Cell resistivity and membrane resistivity at charging periods are higher than at discharging periods. And at the same membrane the resistivity were increased with increasing SOC. The resistivity of hydrocarbon type Seiemion CMV membrane was smaller than perfluoro type Nafion 117 and Nafion 551. The cell resistivity and membrne resistivity of CMV membrane at 0 % SOC was $12.864\Omega \textrm{cm}^2$ and $8.751\Omega \textrm{cm}^2$, respectively.

• Journal of the Korean Electrochemical Society
• /
• v.12 no.3
• /
• pp.245-250
• /
• 2009

Crosslinked membrane based on sulfonated polyimide was prepared by the introduction of crosslinkable monomer in polymerization process and crosslinking during membrane casting. Crosslinked membranes showed different properties from non-crosslinked membranes. Crosslinking decreased methanol crossover and therefore unit cell using crosslinked membrane showed increased open circuit voltage, 0.81 V, in comparison with unit cell using noncrosslinked membrane, 0.71 V. In addition, water uptake of crosslinked membrane, 40.5%, was lower than that of non-crosslinked membrane, 57.0%, and this resulted in improved dimensional stability. However, proton conductivity of crosslinked membranes showed rather low relative to non-crosslinked membrane due to reduced water uptake.

• Macromolecular Research
• /
• v.16 no.5
• /
• pp.457-466
• /
• 2008

The relation between the phase separated morphologies and their transport properties in the polymer blend membrane for direct methanol fuel cell application was studied. In order to enhance the proton conductivity and reduce the methanol crossover, sulfonated poly(arylene ether sulfone) copolymer, with a sulfonation of 60 mol% (sPAES-60), was blended with nonsulfonated poly(ether sulfone) copolymer (RH-2000, Solvay). Various morphologies were obtained by varying the drying condition and the concentration of the casting solution (10, 15, 20 wt%). The transport properties of proton and methanol molecule through the polymer blend membranes were studied according to the absorbed water. AC impedance spectroscopy was used to measure the proton conductivity and a liquid permeability measuring instrument was designed to measure the methanol permeability. The state of water in the blend membranes was confirmed by differential scanning calorimetry and was used to correlate the morphology of the membrane with the membrane transport properties.

• Journal of Periodontal and Implant Science
• /
• v.50 no.5
• /
• pp.327-339
• /
• 2020

Purpose: The purpose of this study was to examine the local tissue reactions associated with 3 different poly(lactic-co-glycolic acid) (PLGA) prototype membranes and to compare them to the reactions associated with commercially available resorbable membranes in rats. Methods: Seven different membranes-3 synthetic PLGA prototypes (T1, T2, and T3) and 4 commercially available membranes (a PLGA membrane, a poly[lactic acid] membrane, a native collagen membrane, and a cross-linked collagen membrane)-were randomly inserted into 6 unconnected subcutaneous pouches in the backs of 42 rats. The animals were sacrificed at 4, 13, and 26 weeks. Descriptive histologic and histomorphometric assessments were performed to evaluate membrane degradation, visibility, tissue integration, tissue ingrowth, neovascularization, encapsulation, and inflammation. Means and standard deviations were calculated. Results: The histological analysis revealed complete integration and tissue ingrowth of PLGA prototype T1 at 26 weeks. In contrast, the T2 and T3 prototypes displayed slight to moderate integration and tissue ingrowth regardless of time point. The degradation patterns of the 3 synthetic prototypes were similar at 4 and 13 weeks, but differed at 26 weeks. T1 showed marked degradation at 26 weeks, whereas T2 and T3 displayed moderate degradation. Inflammatory cells were present in all 3 prototype membranes at all time points, and these membranes did not meaningfully differ from commercially available membranes with regard to the extent of inflammatory cell infiltration. Conclusions: The 3 PLGA prototypes, particularly T1, induced favorable tissue integration, exhibited a similar degradation rate to native collagen membranes, and elicited a similar inflammatory response to commercially available non-cross-linked resorbable membranes. The intensity of inflammation associated with degradable dental membranes appears to relate to their degradation kinetics, irrespective of their material composition.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1824-1826
• /
• 1999

In order to develop key technologies for a kW class for polymer electrolyte fuel cell (PEFC), various membranes (Nafion(112, 115, 117), Dow, Flemion, Gore, and Hanwha), and electrocatalysts (Pt/C, PtNi/C PtNiCo/C and PtRu/C) were used in the fabrication of the MEAs by using transfer printing technique. The effects of the thickness of Nafion membranes, electrocatalysts and the operating conditions (e.g. temperature, reactant gas pressure, and composition) on the performance of the MEA were investigated in the PEFC single cell($O_2/H_2$, and Air/$H_2$ cell). The performances of the MEAs for $O_2/H_2$ and Air/$H_2$ cells has been evaluated.