• Structural Engineering and Mechanics
• /
• 제90권6호
• /
• pp.611-633
• /
• 2024

This study intends to investigate the response of multi-cell (MC) beams to flexural loads in which the primary reinforcement is composed of both metallic and non-metallic materials. "Multi-cell" describes beam sections with multiple longitudinal voids separated by thin webs. Seven reinforced concrete MC beams measuring 300×200×1800 mm were tested under flexural loadings until failure. Two series of beams are formed, depending on the type of main reinforcement that is being used. A control RC beam with no openings and six MC beams are found in these two series. Series one and two are reinforced with metallic and non-metallic main reinforcement, respectively, in order to maintain a constant reinforcement ratio. The first crack, ultimate load, deflection, ductility index, energy absorption, strain characteristics, crack pattern, and failure mode were among the structural parameters of the beams under investigation that were documented. The primary variables that vary are the kind of reinforcing materials that are utilized, as well as the kind and quantity of mesh layers. The outcomes of this study that looked at the experimental and numerical performance of ferrocement reinforced concrete MC beams are presented in this article. Nonlinear finite element analysis (NLFEA) was performed with ANSYS-16.0 software to demonstrate the behavior of composite MC beams with holes. A parametric study is also carried out to investigate the factors, such as opening size, that can most strongly affect the mechanical behavior of the suggested model. The experimental and numerical results obtained demonstrate that the FE simulations generated an acceptable degree of experimental value estimation. It's also important to demonstrate that, when compared to the control beam, the MC beam reinforced with geogrid mesh (MCGB) decreases its strength capacity by a maximum of 73.33%. In contrast, the minimum strength reduction value of 16.71% is observed in the MC beams reinforced with carbon reinforcing bars (MCCR). The findings of the experiments on MC beams with openings demonstrate that the presence of openings has a significant impact on the behavior of the beams, as there is a decrease in both the ultimate load and maximum deflection.

• 한국수소및신에너지학회논문집
• /
• 제17권1호
• /
• pp.82-89
• /
• 2006

The redox behaviors of anode-supported flat tube for solid oxide fuel cell has been studied. The mass change of the extruded NiO/YSZ anode flat tube during redox cycling was examined by thermogravimetric analysis(TGA). The result of TGA was shown a rapidly mass change in the range of $455\;-\;670^{\circ}C$ and the reoxidation of the NiO/YSZ anode was almost completed at $750^{\circ}C$. The starting temperature of reoxidation and the maximum temperature of oxidation rate decreased with increasing the reoxidation cycle, which is attributed to the increased porosity caused by volume change. Bending strengths of the NiO/YSZ anode after redox cycling were 96 - 80 MPa and the bending strength decreased slightly with increasing the redox cycle. On the other hand, the bending strength of the NiO/YSZ anode with electrolyte showed 130 MPa after first redox cycling but decreased rapidly with increasing the redox cycle. From the results of the bending test and the microstructure observation, we conclude that the crack initiation of the electrolyte-coated NiO/YSZ anode was induced easily at interface of electrolyte/anode tube and propagated cross the electrolyte.

• Journal of Electrochemical Science and Technology
• /
• 제13권2호
• /
• pp.269-278
• /
• 2022

Utilization of high-voltage electrolyte additive(s) at a small fraction is a cost-effective strategy for a good solid electrolyte interphase (SEI) formation and performance improvement of a lithium-rich layered oxide-based high-energy lithium-ion cell by avoiding the occurrence of metal-dissolution that is one of the failure modes. To mitigate metal-dissolution, we explored fluorinated dual-additives of fluoroethylene carbonate (FEC) and di(2,2,2-trifluoroethyl)carbonate (DFDEC) for building-up of a good SEI in a 4.7 V full-cell that consists of high-capacity silicon-graphite composite (15 wt% Si/C/CF/C-graphite) anode and Li_1.13Mn_0.463Ni_0.203Co_0.203O₂ (LMNC) cathode. The full-cell including optimum fractions of dual-additives shows increased capacity to 228 mAhg^-1 at 0.2C and improved performance from the one in the base electrolyte. Surface analysis results find that the SEI stabilization of LMNC cathode induced by dual-additives leads to a suppression of soluble Mn²⁺-O formation at cathode surface, mitigating metal-dissolution event and crack formation as well as structural degradation. The SEI and structure of Si/C/CF/C-graphite anode is also stabilized by the effects of dual-additives, contributing to performance improvement. The data give insight into a basic understanding of cathode-electrolyte and anode-electrolyte interfacial processes and cathode-anode interaction that are critical factors affecting full-cell performance.

• Korean Chemical Engineering Research
• /
• 제50권3호
• /
• pp.562-566
• /
• 2012

본 논문에서는 세그먼트 관형 고체산화물 연료전지(SOFC)의 설계 및 제작과 특성 분석을 다루고 있다. 관형 세라믹 지지체는 압출 공정을 통하여 제작하였으며, NiO-YSZ 연료극과 YSZ 전해질은 담금 코팅법을 통해 세라믹 지지체에 코팅하였다. 코팅된 세라믹 지지체를 $1,350^{\circ}C$에서 5시간 동안 열처리하였으며, $10{\mu}m$ 미만의 치밀하고, 균열이 없는 YSZ 전해질 층을 얻을 수 있었다. 또한 열처리된 세라믹 지지체에 LSM-YSZ/LSM/LSCF로 구성된 다층 구조 공기극을 담금법으로 코팅하여 $1,150^{\circ}C$에서 열처리하였다. 세라믹 관형 지지체에 코팅된 세그먼트 SOFC 셀은 Ag-glass 연결재를 사용하여 전기적으로 직렬 연결하였으며, 수소연료 유량과 운전 온도에 따른 세그먼트 SOFC의 성능 변화를 측정하였다.

• 한국안전학회지
• /
• 제30권1호
• /
• pp.21-27
• /
• 2015

In this study, interfacial characteristics between SOFC and Ag paste as current collector was estimated in the high temperature environment. The Ag paste was used to connect the unit cell of SOFC strongly with interconnector and provide the electrical conductivity between them. To confirm electrical conductivity, Ag paste was treated in the furnace at $800^{\circ}C$ for 48 hours. The sheet resistance of Ag paste was measured to compare the resistance values before and after the heat treatment. Also, the four-point bending test was performed to measure the interfacial adhesion. The unit cell of SOFC and $SiO_2$ wafer were diced and then attached by Ag paste. The $SiO_2$ wafer had the center notch to initiate a crack from the tip of the notch. The modified stereomicroscope combined with the CCD camera and system for measuring the length was used to observe the fracture behavior. To compare the characteristics before heat treatment and after heat treatment, the specimen was exposed in the furnace at $800^{\circ}C$ for 48 hours and then the interfacial adhesion was evaluated. Finally, the interfacial adhesion energy quantitatively increases $1.78{\pm}0.07J/m^2$ to $4.9{\pm}0.87J/m^2$ between the cathode and Ag paste and also increase $2.9{\pm}0.47J/m^2$ to $5.12{\pm}1.01J/m^2$ between the anode and Ag paste through the high temperature. Therefore, it is expected that Ag paste as current collector was appropriate for improving the structural stability in the stacked SOFC system if the electrical conductivity was more increased.

• 한국수소및신에너지학회논문집
• /
• 제24권3호
• /
• pp.230-236
• /
• 2013

In this study, successive coating and co-sintering techniques have been used to fabricate LSM/GDC based cathode supported direct carbon fuel cells. The porous LSM/GDC cathode substrate, dense, thin and crack free GDC and ScSZ layers as bi-layer electrolyte, and a porous Ni/ScSZ anode layer was obtained by co-firing at $1400^{\circ}C$. The porous structure of LSM/GDC cathode substrate, after sintering at $1400^{\circ}C$, was obtained due to the presence of GDC phase, which inhibits sintering of LSM because of its higher sintering temperature. The electrochemical characterization of assembled cell was carried out with air as an oxidant and carbon particles in molten carbonate as fuel. The measured open circuit voltages (OCVs) were obtained to be more than 0.99 V, independent of testing temperature. The peak power densities were 116, 195 and $225mWcm^{-2}$ at 750, 800 and $850^{\circ}C$, respectively.

• 한국정보과학회논문지:시스템및이론
• /
• 제27권3호
• /
• pp.235-244
• /
• 2000

본 논문에서는 단층 촬영 영상(tomographic cross-section image)에 포함되어 있는 볼륨 정보를 표현하기 위한 새로운 방법을 제안하였다. 이 방법은 큐베릴 공간을 셀 공간으로 변환하고 경계셀들을 추출하여 볼륨을 재구성하는 방법이다 셀 경계 표현은 이러한 경계셀들과 이들의 지지 복셀들의 구조에 의해 표현되어 지는데, 항상 볼륨 정보를 정확하게 표현해낼 수 있다. 이 표현에서부터 가시화등의 작업에 필요한 표면모델을 추출하기 위해 19개의 모델링 원형을 제안하고 체적형, 표면형 그리고 선형으로 분류하였으며， 이들로부터 3차원 표면을 표 참조방식으로 빠르게 추출할 수 있는 알고리즘을 제안하였다. 제안된 방법의 장점은 기존에 제안된 마칭 큐브나 PVP알고리즘 등에서 흔히 발생하는 표면생성시의 모호성문제가 전혀 발생하지 않으며, 마칭 큐브 알고리즘에서 발생하는 표면의 크랙문제도 완전히 해결된다는 장점이 있다. 또한 알고리즘이 표 참조방식을 취하므로 하드웨어화 하기가 매우 용이하여 고속의 모델링이 필요한 분야에 매우 적합한 방법이다.

• 한국작물학회지
• /
• 제49권4호
• /
• pp.316-324
• /
• 2004

Sinorhizobium sp. strain MUS10 forms nitrogen-fixing stem nodules on Sesbania rostrata, a tropical green manure crop. In this study, the ultrastructural events associated with the formation of stem nodules were investigated. Sinorhizobium sp. strain MUS10 entered the host tissue through cracks created by the emerging adventitious root primordia and multiplied within the intercellular spaces. During early phases of infection, host cells adjacent to invading bacteria revealed cellular damage that is typical of hypersensitive reactions, while the cells at the inner cortex exhibited meristematic activity. Infection threads were numerous in S-day-old nodules and often were associated with the host cell wall. In several cases, more than one infection thread was found in individual cells. The junction at which the host cell walls converged was often enlarged due to fusion of intracellular branches of infection threads resulting in large infection pockets. The infection threads were made up of a homogeneous, amorphous matrix that enclosed the bacteria. Several finger-like projections were seen radiating from these enlarged infection threads and were delineated from the host cytoplasm by the plasma membrane. As in Azorhizobium caulinodans induced root nodules, the release of Sinorhizobia from the infection threads into the plant cells appears to be mediated by 'infection droplets'. A 15-day­old Sesbania stem nodule revealed typical ultrastructure features of a determinate nodule, containing several bacterioids within symbiosomes.

• 한국세라믹학회지
• /
• 제52권5호
• /
• pp.304-307
• /
• 2015

To reduce the lateral conduction loss of thin-film-processed cathodes, the microstructure of the thin-film cathode is engineered to contain a denser bridging layer in the middle. By doing so, the characteristic crack-like pores that separate the cathode domains in thin-film-processed cathodes and hamper lateral conduction are better connected and, as a result, the sheet resistance of the cathode is effectively reduced by a factor of 5. This induces suppression of the lateral conduction loss and expansion of the effective current collecting area; the cell performance is improved by more than 30%.

• 한국식품영양과학회지
• /
• 제32권3호
• /
• pp.370-374
• /
• 2003

홍삼 분쇄의 신 가공 기술로서 비충격 분쇄방식인 cell cracker의 공장 적용 가능성을 제시하고 홍삼분말의 품질고급화에 기초자료로 활용하고자, 기존의 hammer mill(충격분쇄방식)과 cell cracker에 의한 분쇄방식으로 홍삼분말을 제조한 후 물성, 표면구조적 특성 및 관능적 특성을 측정하였다. 입도분석에서 sieve shaker로 분석한 결과, 100 mesh 이상은 모두 95%수준으로 비슷한 분포를 나타냈고 120 mesh 이상은 hammer mill로 분쇄한 홍삼분말이 높았으며 그 밖의 각 mesh별 입도분포는 큰 차이를 나타내지 않았다. Laser scattering analyzer로 분석한 결과 hammer mill로 분쇄한 홍분말의 입도분포는 최소 0.77$\mu\textrm{m}$에서 최대 128.07$\mu\textrm{m}$으로, cell cracker로 분쇄한 홍삼분말 4.24~180.07$\mu\textrm{m}$보다 분포가 넓었으며, 평균 입자 크기는 cell cracker로 분쇄한 홍삼분말이 크고 표준편차는 hammer mill로 분쇄한 홍삼분말이 크게 나타났다. 비표면적은 hammer mill로 분쇄한 홍삼분말이 1.42 $m^2$/g로 cell cracker로 분쇄한 홍삼분말 0.59 $m^2$/g보다 높게 나타났고, 표면구조적 특성은 hammer mill로 분쇄한 홍삼분말은 크고 작은 입자가 불균일하게 분포하고 있으며, 개별입자의 형태는 부등형의 거칠게 연마된 돌 모양에 가깝고 표면은 작고 부드러운 솜털모양을 하고 있는 반면에, cell cracker로 분쇄한 홍삼분말은 입자크기가 상대적으로 고르게 분포하고 있으며 개별입자의 형태는 부등형의 조각난돌 모양의 형태로 관찰되었다.