• Journal of the Korean Ceramic Society
• /
• v.33 no.9
• /
• pp.1057-1063
• /
• 1996

Y2O3-CeO2-ZrO2 powders were prepared from water-soluble salts using a coprecipitation method. The forming process of oxide and the characteristics of the calcined powders treated in different drying conditions were investigated. The oxidation was occurred at the temperature of around 40$0^{\circ}C$ and the main crystallization of ZrO2 around $600^{\circ}C$. On calcination at $600^{\circ}C$ heating lamp-dried powders consisted of agglomerates of globular morphology with average agglomerate size of 2.27${\mu}{\textrm}{m}$ and specific surface area of 68.3m2/g and spray dried powders contained dense spheric particles with average agglomerate size of 1.35${\mu}{\textrm}{m}$ and specific surface area of 11.0m2/g which exhibited low agglomeration tendency. Removal of the water by a freeze-drying technique produced calcined powders containing flake-like secondary particle structures with wide agglomerate size distri-bution of 0.1-60${\mu}{\textrm}{m}$ and specific surface area of 24.5${\mu}{\textrm}{m}$. The 20 MPa-pressed density (36.8-41.4% T,D) of calcined powders did not nealy depend on drying methods whilst compaction ratio of calcined powders derived from freeze-drying was the highest ( 6.24) among three drying methods. On continuous heating up to 150$0^{\circ}C$ the sinterability of calcined powders derived from heating lamp-drying was superior to those derived from spray-and freeze-drying. The final sintered density of calcined powders was the highest (96% T,D at 150$0^{\circ}C$) in case of heating lamp-drying.

• Korean Journal of Materials Research
• /
• v.26 no.4
• /
• pp.212-215
• /
• 2016

In this paper, cerium doped lutetium pyrosilicate (LPS) powders with cerium content (0.05 and 0.07 mol%) were prepared by sol-gel process. The formation of lutetium pyrosilicate (LPS) phase was confirmed by XRD analysis for the powders heated at $1,200^{\circ}C$; in these powders, a single phase of $Lu_2Si_2O_7$ (LPS) was observed. Cerium doped lutetium pyrosilicate (LPS) powder was agglomerated and constituted of small spherical particles with diameters of about 300 nm. The photoluminescence spectra of the $Lu_2Si_2O_7:Ce^{3+}$ powders showed the characteristic of excitation and there was an emission spectrum for $Ce^{3+}$ in the host of $Lu_2Si_2O_7$. The emission spectrum shows a broad band in the range of 350-525 nm; the broad wavelength on the right side of the spectra should be ascribed to the same 5d-4f transitions of $Ce^{3+}$, as in the case of cerium doped $Lu_2Si_2O_7$ single crystals.

• 한국초전도학회:학술대회논문집
• /
• 2009.07a
• /
• pp.97-97
• /
• 2009

• 한국초전도학회:학술대회논문집
• /
• v.12
• /
• pp.38-38
• /
• 2002

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.9
• /
• pp.611-615
• /
• 1999

Piezoelectric properties of PMN-PZT ceramics with $CeO_2$ impurity were investigated. Mechanical quality factor, $Q_m$ of 1792, 1285 and the electromechanical coupling coefficient, $k_p$ of 0.52, 0.54 were obtained from the specimen with 0.25 and 0.5 mole % $CeO_2$ respectively. Curie temperature was decreased with the addition of $CeO_2$ while the electric coercive field was proportional to the amount of impurity. Based on the system ceramics with 0.5 mole % cerium oxide, a Rosen type piezoelectric transformer was fabricated and tested. Voltage step-up ratios of 230 and 13 were obtained from the transformer at no load and $100 k\Omega$ resistance, respectively. Experimental results showed a potential of the transformer for the practical use coupled with the expected strength increase by the grain size refinement.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.236-237
• /
• 2005

The structural properties of $(Bi,Ce)_4Ti_3O_{12}(BCT)$ thin films with post-annealing temperature were investigated. $(Bi,Ce)_4Ti_3O_{12}(BCT)$ thin films were deposited by RF sputtering method on Pt/Ti/$SiO_2$/Si substrates with optimum deposition condition. The $(Bi,Ce)_4Ti_3O_{12}(BCT)$ thin films was post-annealed at 600$^{\circ}C$, 650$^{\circ}C$, 700$^{\circ}C$, 750$^{\circ}C$, 800$^{\circ}C$ in furnace,respectively. Increasing the post-annealing temperature, the grain size, density and peak intensity of (117) and c-axis orientation were increased. The $(Bi,Ce)_4Ti_3O_{12}(BCT)$ thin films that annealed at 750$^{\circ}C$ exhibited well crystallized phase and had no vacancy and grain was uniform. but there are some secondary phases observed. At this time, the average thickness of $(Bi,Ce)_4Ti_3O_{12}(BCT)$ thin films was 2000 ${\AA}$.

• Journal of the Korean Ceramic Society
• /
• v.38 no.8
• /
• pp.698-704
• /
• 2001

Doped ceria의 전기전도도는 도핑 원소의 종류와 양에 큰 의존성을 가지고 특정 조성에서 최대 전도도 값을 가지며 높은 dopant 농도에서는 전기전도도는 감소한다. 이런 현상은 dopant와 산소 빈자리 사이의 회합 형성과 관련이 있다고 알려져 있다. 그러나 Gd 이온이 도핑된 ceria의 경우 주된 회합종이 (2G $d_{Ce}$ $V_{o}$ )인지 (G $e_{Ce}$ $V_{o}$ ) 인지는 명확하게 알려져 있지 않다. 본 연구에서는 회합분포가 전기전도도에 미치는 영향을 연구하기 위해 결함의 회합종과 분포가 다른 3가지 경우에 대해서 시뮬레이션을 행하였다. 분자동력학법을 이용하여 다양한 온도와 다른 회합분포의 경우에 대해 산소 확산계수가 계산되어졌으며, 계산된 산소 확산계수는 실험적으로 결정된 bulk 전도도로부터 얻어진 산소 확산계수와 비교되어졌다. 그 결과 (2G $d_{Ce}$ $V_{o}$ )와 (G $e_{Ce}$ $V_{o}$ ) 회합이 공존하며 이들이 통계학적으로 이항 분포를 가지는 경우가 실험적으로 보고된 값과 가장 일치하는 결과를 얻을 수 있었다.

• Ceramist
• /
• v.21 no.4
• /
• pp.378-387
• /
• 2018

The optimal fabrication conditions for $Gd_{0.1}Ce_{0.9}O_{2-{\delta}}$(GDC) buffer layer and $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_{3-{\delta}}$ (LSCF) cathode on 1mol% $CeO_2-10mol%\;Sc_2O_3$ stabilized $ZrO_2$ (CeScSZ) electrolyte were investigated for application of IT-SOFCs. GDC buffer layer was used in order to prevent undesired chemical reactions between LSCF and CeScSZ. These experiments were carried out with $5{\times}5cm^2$ anode supported unit cells to investigate the tendencies of electrochemical performance, Microstructure development and interface reaction between LSCF/GDC/CeScSZ along with the variations of GDC buffer layer thickness, sintering temperatures of GDC and LSCF were checked, respectively. Electrochemical performance was analyzed by DC current-voltage measurement and AC impedance spectroscopy. Microstructure and interface reaction were investigated by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). Although the interfacial reaction between these materials could not be perfectly inhibited, We found that the cell, in which $6{\mu}m$ GDC interlayer sintered at $1200^{\circ}C$ and LSCF sintered at $1000^{\circ}C$ were applied, showed good interfacial adhesions and effective suppression of Sr, thereby resulting in fairly good performance with power density of $0.71W/cm^2$ at $800^{\circ}C$ and 0.7V.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.100.2-100
• /
• 2003

• Journal of Hydrogen and New Energy
• /
• v.23 no.4
• /
• pp.346-352
• /
• 2012

The properties of methane oxidation were studied in this research over transition metal containing $CeO_2$ (TM/$CeO_2$, TM=Ni, Co, Cu, Fe) with TM content of 5 wt. % at atmospheric pressure. The characteristics of catalysts were investigated by various characterization techniques, including XRD, GC, SEM and EPMA analyses. The catalytic tests were carried out in a fixed Rmix ratio of 1.5 ($CH_4/O_2$) in a fixed-bed reactor operating isothermally at atmospheric pressure. Only the Ni/$CeO_2$ catalysts showed syngas production above $400^{\circ}C$ via typical partial oxidation reaction whereas other catalysts induced complete oxidation resulting in the production of $CO_2$ and $H_2O$ in whole reaction temperature range. From the quantitative analysis on carbon deposition after catalytic tests, Cu/$CeO_2$ was found to show the highest resistance on carbon deposition. Therefore Cu can be proposed as an efficient catalyst element which can be combined with a conventional Ni-based SOFC anode to enhance the carbon tolerance.