• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.12
• /
• pp.43-53
• /
• 2007

We have analyzed low current operation characteristics of a VCSEL transmitter operating at fixed Current over wide temperature range. Used 850 nm oxide VCSEL has low temperature dependence of the threshold current and $d^2I_{th}/dT^2$ is approximately $1.346\times10^{-4}mA/^{\circ}C^2$. We fixed on-current so that output power from the chip is 1 mW at $20^{\circ}C$ and investigated the turn-on, turn-off characteristics and eye-diagram of the 850 nm oxide VCSEL transmitter with varying ambient temperature and off-current. We measured rise time, fall time, extinction ratio and timing jitter by changing tile ambient temperature and off-current. With the fixed off-current of around $0.1\sim0.2mA$ lower than the lowest threshold current the transmitter successfully operated at 1.25 Gbps over a wide temperature range from $-20^{\circ}C$ to $80^{\circ}C$.

• Journal of Sensor Science and Technology
• /
• v.7 no.3
• /
• pp.171-178
• /
• 1998

Silicon piezoresistive absolute pressure sensor for gas leakage alarm system was developed. This sensor must operate normally in the range of $0{\sim}600\;mmH_{2}O$ pressure, and $0{\sim}100^{\circ}C$ temperature. To make the most of this sensor for gas leakage alarm system, gas must not leak from the sensor itself when the diaphragm of the sensor fractures. Thus, the sealed diaphragm cavity was anodically bonded to pyrex 7740 glass under the condition of $10^{-4}$ torr, at $400^{\circ}C$. The sensitivity of developed sensor was $4.06{\mu}V/VmmH_{2}O$ for $600\;mmH_{2}O$ full-scale pressure range. And temperature compensation method of this sensor is to change bridge-in put-voltage linearly in proportion to the temperature variation by using diode(PXIN4001) or Al thin film resistor. By these methods the temperature effect in the range of $0{\sim}100^{\circ}C$ was compensated over 80 % for offset drift, 95 % for sensitivity.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.33 no.5
• /
• pp.373-377
• /
• 2000

This study Investigated the effects of $estradiol-l7{\beta} (E_2)$, $17{\alpha}-methyltestosterone$ (MT) and high temperature (WT) on gonadal sex differentiation in black rockfish, Sebastes srhlegeli. fish were reared to oral adminstration of E, at nominal concentrations of $20, 40 and 60 {\mu}g/g diet$, and MT at nominal concentration of 20 and $50 {\mu}g/g$ diet from 56 days to 77 days after parturition. In the treatment of WT, water temperature of the breeding tanks ranged $27.0{\pm}0.5^{\circ}C$ more than $10^{\circ}C$ approximately, in comparison to the control and other experimental group, In the process of sex differentiation until 56 days after parturition, gonads were composed of mostly gonia cells, sexually undifferentiated. In contrast, 128 dal's after parturition, the ovaries were composed of ovarian cavity and lamellae, and oogonia and perinucleolus oocytes were distributed in the lamellae of ovary, and the testes were composed of a number of seminiferous tubule, and spermatogonia were distributed in the seminiferous tubule, and also melanophore scattered in the matrix layer of testis. In the sex ratio, more females than male were observed from $E_2$. treatment groups when compared to the control, but more males than females were observed from MT and WT treatment groups when compared to the control. In the results of the present study, the concentration and kinds of the sex steroid hormones, and also the rearing high temperature caused to the factor of sex determination in the process of sex differentiation of black rockfish.

• Journal of Korea Foundry Society
• /
• v.20 no.5
• /
• pp.344-353
• /
• 2000

In order to find out the casting conditions of the thin wall stainless steel exhaust manifold for automobile, the melt flow and solidification behavior simulated by the Z-CAST program were evaluated, and experimental casting result on the test casting and exhaust manifold of SSC13 alloy were investigated. From the results of this study, it was shown that the calculated results on fluid flow were in good agreement with practical thin wall test castings under the same casting conditions, as pouring metal is austenitic stainless steel(SSC13) and pouring temperature is 1575, 1630, and $1665^{\circ}C$ respectively. That calculated result with designed thin wall exhaust manifold was predicted filling up into the mold cavity, and practical casting was sound. The solidification simulation was predicted shrinkages at the bosses for original exhaust manifold, and designed it without bosses was predicted no defect. Therefore practical exhaust manifold casting was sound and in good agreement with calculated solidification results.

• The Korean Journal of Rheology
• /
• v.11 no.2
• /
• pp.153-158
• /
• 1999

An improved method to predict preferred direction of gas in gas assisted injection molding processes is introduced. Resistance of resin flow is defined and this resistance of resin flow is not directly related to the resistance of gas flow. Pressure drop requirement was believed to be proportional to the resistance to gas flow in our previous work. Instead of using the pressure drop requirement, velocity of resin should be compared to predict the gas flow direction. This method predicts the gas flow direction from the knowledge of process variables such as resin flow length, cross section area of cavity, melt temperature, and short shot. A simulation package was used to confirm the method.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.7
• /
• pp.569-576
• /
• 2014

Sensor node means a device to include sensor, amplifier, and data acquisition (DAQ) equipment. The sensor converts physical signals to electric signals and weak signals from the sensor can be amplified through the amplifier. DAQ equipment converts analog signal to digital signal and collects converted digital signal. Since the sensor node is sensitive to the environment so that selection of mounting position and fixture design of sensor are applied differently depending on the characteristics of a target. This study is about designing and manufacturing sensor node to be used in a machine tool. The environment of machine tool is very severe due to noise, temperature fluctuation, and dust, etc. Hence, the sensor and amplifier must be designed and manufactured by considering the environmental issues. The designed and manufactured sensor node was tested for the reliability and effectiveness of the developed sensor nodes in the study.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.3
• /
• pp.513-517
• /
• 1998

Fly ashes mixed with clay as 70:30 weight percent were sintered by microwave energy and a 2.45 Ghz kitchen model microwave oven was used. Samples were sintered at $1,150^{\circ}C$ and kept at that temperature up to 50 minutes by 10 minutes intervals. Microstructures were taken by Scanning Electron Microscope (SEM) and Energy Dispersive Spectrometry (EDS) analysis of a raw fly ash was taken. X-ray diffraction analysis was done, and compressive strengths and apparent densities were measured. Pore sizes of the samples became smaller as time passed by, but compressive strengths and apparent densities did not change much. Numerical analysis on the microwave heated system was carried out in order to figure out heat transfer phenomena in the cavity.

• Elastomers and Composites
• /
• v.52 no.4
• /
• pp.317-325
• /
• 2017

Molding conditions can be described as factors that determine the quality of a product obtained from injection molding. Many studies have been performed on the injection molding pressure, injection temperature, packing pressure and other molding conditions related to part quality. However, the most accessible factor among the adjustable molding conditions during actual injection is the injection speed. In this study, we simulated the variation of the physical quantity according to injection speed and performed experiments to understand the effect of injection speed on the actual product. A CAE analysis program (Moldflow) was used to simulate and analyze the results using PC and PBT for two models. In order to compare these results with the experimental results, an actual injection molding was performed for each injection speed, and the correlation between simulation and injection molding, especially for the shrinkage of the molded article, was discussed.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.240-245
• /
• 2001

Phenomena of direct contact condensation (DCC) heat transfer between steam and water are characterized by the transport of heat and mass through a moving steam/water interface. Application of the phenomena of DCC heat transfer to the engineering industries provides some advantageous features in the viewpoint of enhanced heat transfer. This study proposes a simple condensation model on the steam jets discharging into subcooled water from a single horizontal pipe for the prediction of the steam jet shapes. The analysis model was derived from the mass, momentum and energy equations as well as a thermal balance equation with condensing characteristics at the steam/water interface for the axi-symmetric coordinates. The extremely large heat transfer rate at the steam/water interface was reflected in the effective thermal conductivity estimated from the previous experimental results. The analysis results were compared with the experimental ones. The analysis model predicted that the steam jet shape (i. e. radius and length) was increasing as the steam mass flux and the pool temperature were increasing, which was similar in trend to that observed in the experiment.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.3
• /
• pp.403-408
• /
• 2008

The gyroscope is the sensor for detecting the rotation in inertial reference frame and constitute the navigation system together an accelerometer. As the inertial reference equipment for attitude determination and control in the satellite, the mechanical gyroscope has been used but it bring the disturbance for mass unbalance so the disturbance give a bad influence to the observation satellite mission because the mechanical gyroscope has the rotation parts. During the launch. The mechanical gyroscope is weak in vibration, shock and has the defect of narrow operating temperature range so it need the special design in integration. Recently the low orbit observation satellite for seeking the high pointing accuracy of image camera payload accept the FOG(Fiber Optic Gyro) or RLG(Ring Laser Gyro) for the attitude determination and control. The Ring Laser Gyro makes use of the Sanac effect within a resonant ring cavity of a He-Ne laser and has more accuracy than the other gyros. It need the 1000V DC to create the He-Ne plasma in discharge tube. In this paper, the design process of the High Voltage Power Supply for RLG(Ring Laser Gyroscope) is described. The specification for High Voltage Power Supply (HVPS) is proposed. Also, The analysis of flyback converter topology is explained. The Design for the HVPS is composed of the inverter circuit, feedback control circuit, high frequency switching transformer design and voltage doubler circuit.