• Journal of the Korea Safety Management & Science
• /
• v.19 no.4
• /
• pp.35-42
• /
• 2017

A number of plating companies have been exposed to the risk of fire due to unexpected temperature increasing of water or other reasons in a plating bath. Since the companies are not able to forecast the unexpected temperature increasing of plating bath and most of raw materials in the bath have low ignition temperature, it is easy to be exposed to the risk of fire. Thus, in previous study, we tried to monitor and notice the dangerous change of temperature of water immediately to prevent the risk of fire from plating process. However, unfortunately previous studies were not able to shut out the fundamental cause of fire since bath temperature sensor can detect air temperature when the level sensor was malfunctioned. In this paper we developed the Teflon heater which contains a built in temperature sensor and improved plating equipment system. Teflon heater is improved using Pt $100{\Omega}$ sensor which can detect until $600^{\circ}C$. When the bath temperature sensor detects over $60^{\circ}C$ or the Teflon heater sensor detects over $240^{\circ}C$ they temporarily shut down the heater to control temperature. Also relay completely shuts down main power when detects instant temperature is detected over 5% of $240^{\circ}C$ by the heater sensor to prevent teflon melting down and fire spreads. Developed plating equipment system can monitor a real time temperature in the teflon tube and bath water. Therefore we think the proposed plating equipment can eliminate the possibility of fire in plating processes fundamentally.

• Fire Science and Engineering
• /
• v.10 no.1
• /
• pp.3-9
• /
• 1996

Electrostatic charge is generated in large scale or high speed processes dealing with materials with large resistance, or under complicated condition. Fire and explosion often occur due to electrostatic charge accumulated in flammable gases, vapor, liquids and powder. It is usually very difficult to verify the cause of accidents as well as the prevention. In this study, it is shown that the needle electrode needs the electrode gap from 1.8mm to 3.8mm, sphere electrode and plate electrodes need the electrode gap of 1.9mmfor the minimum ignition energy. The sphere electrode and the plate electrode requires 12.8mJ and 3.2mJ of minimum ignition energy respectively with the electrode gap of 1.1mm. The ignition voltage rises to very large value as the ground resistance increases.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.8 no.4
• /
• pp.63-71
• /
• 2012

Recently, because most of buildings in the city become bigger and higher, so various convenient facilities and high-tech management skills are required to prevent potential disasters. Especially, because fires in huge buildings can cause serious damage, technologies and methods that help people quickly and safely to escape from the building is very important to extinguish the fire in initial state and to minimize the damage. This paper suggests a context-aware service system that can provide optimal escape routes to tenants with their smart-phones. The proposed system collects contexts with real time through USN(Ubiquitous Sensor Network) and provides an optimum escape route based on the collected contexts through service users' smart phones. In addition, The system provides not only safe routes from the fire but also valuable information for rescue operations with real time.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2011.04a
• /
• pp.77-79
• /
• 2011

본 논 연구에서는 가전제품 중에서 야간 절전 버튼의 작동 불량 원인을 규명하여 제품의 성능 및 신뢰성 향상을 위한 객관적 근거를 제시하였다. 시판된 제품을 수거하여 불량품 검사(전기적 특성 및 decap)를 실시한 결과 절전 버튼 IC pin No.2의 단락(short)에 의한 오작동 요소를 밝힐 수 있었다. 동일한 사양의 재현실험에서 EOS(전기적 과도전압에 의한 스트레스)보다 정전기 방전에 스트레스에 의해서 소손되는 특성을 나타내는 것을 확인할 수 있었다. 오작동 요소로 확인된 IC pin 2번에 바리스터(Varistor)를 부착하고 11kV를 인가하여 시험한 결과 오작동 요소를 제거할 수 있었다.

• Fire Science and Engineering
• /
• v.23 no.5
• /
• pp.57-65
• /
• 2009

This study was intended to conduct a Real-scale fire test to predict the fire behavior by unit space at the apartment building where a huge casualties and injuries are likely. After setting the inflammables inside the house, the test aimed to identify the fire characteristics to each unit item was carried out. The house was divided into 4 unit space such as kitchen, living room, bedroom and a study for a real scale fire test. As a result, bedroom reached to flashover state in 5minutes after setting the fire, indicating a rapid fire growth such as 7433.3kW of maximum thermal emissivity, 578.6ppm of carbon monoxide, 1.25ppm of carbon dioxide and $1,350^{\circ}C$ of maximum indoor temperature. Particularly, the fire growth was made up to critical temperature which might cause a severe damage to the people within 3minutes, if the fire were not extinguished at inflammable space at the early stage of fire, which stressed the need of early response. The result of a real scale fire test could be compared with the outcome of expanded simulation test and used in predicting the fire spread at the space for different use.

• Journal of Korean Institute of Fire Investigation
• /
• v.10 no.1
• /
• pp.59-75
• /
• 2007

The causes of the fire casualties were the heat burns, contacted by flame, before the period of industrialization. According to the economic has been developed drastically since 1990, residing space has been become bigger and sophistication and interior finishing materials have been diversified. Therefore, the suffocation casualties, caused by inspiration of toxic combustion gases, have been more increased than the flame casualties in recently. Also, the arson casualties have been increasing with the increasing of insurance crime to take the Insurance money. According to National Emergency Management Agency announcement, 31,778 fires was occurred nationwide in 2006 and the total casualties were 2,180 occurred. 446 persons were died among them. Because the exact investigation of fire, occurred the death, is very especially important that civil and criminal cases will be happened. Therefore, we studied about the cause of fire, the place of origin, and the group of casualties age on the axies of fires, which were occurred recently. And the identification method of fire casualties, the human behavior characteristic, the flame casualties and the suffocation casualties at fire scene.

• Journal of Korean Institute of Fire Investigation
• /
• v.10 no.1
• /
• pp.37-45
• /
• 2007

In this paper, the possibility of arc tracking, caused by combustion at the circuit breaker, was discussed. The arc tracking, occurred at the source terminals of all the circuit breakers, when we burned electric leakage circuit breakers with 220V applied. We had a same results of the experiment to simulate fire scene, in the circumstance of fire, all of the circuit breakers had arc tracking caused by combustion. Therefore we confirmed that the arc tracking at the source terminal of circuit breaker could be occurred by just combustion in the fire scene, and it was impossible to decide the cause of fire for reason of discriminating arc tracking at the terminals of circuit breaker.

• International Journal of High-Rise Buildings
• /
• v.2 no.4
• /
• pp.341-344
• /
• 2013

During a building fire, smoke can flow through elevator shafts threatening life on floors remote from the fire. Many buildings have pressurized elevators intended to prevent such smoke flow. The computer program, CONTAM, can be used to analyze the performance of pressurization smoke control systems. The design of pressurized elevators can be challenging for the following reasons: (1) often the building envelope is not capable of effectively handling the large airflow resulting from elevator pressurization, (2) open elevator doors on the ground floor tend to increase the flow from the elevator shaft at the ground floor, and (3) open exterior doors on the ground floor can cause excessive pressure differences across the elevator shaft at the ground floor. To meet these challenges, the following systems have been developed: (1) exterior vent (EV) system, (2) floor exhaust (FE) system, and ground floor lobby (GFL) system.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2010.10a
• /
• pp.227-230
• /
• 2010

본 논문은 부산 실내사격장 화재와 관련하여 급격한 연소 확대 경로 및 발화원인에 대하여 분석하였다. 연소 확대 경로 분석을 위하여 실내사격장에 광범위하게 사용되는 스펀지형 흡음재의 연소실험을 수행하였다. 흡음재 연소 실험은 일반형과 낭연 처리된 흡음재를 대상으로 실시하였으며, 화약잔사 흡착 시, 연소 특성을 평가하였다. 발화원인에 대한 분석을 위하여 총기 사용 과정에서 발생되는 유탄된 탄환의 비산거리 및 크기를 실측하고, 유탄된 탄환에 대한 운동에너지 계산을 통하여 화약잔사와 충격하는 경우, 충분한 발화 가능성이 있음을 확인하였다.

• Fire Science and Engineering
• /
• v.22 no.1
• /
• pp.54-60
• /
• 2008

The occurrence of fires in heavily populated multiplex buildings is a serious concern. It causes a great threat to many people and a serious social problem. Whenever this kind of fire happens, the authorities are busy preparing partial countermeasures to control the crisis situations. Luckily, the government has enforced a special law regarding safety supervision of majority-used buildings to prepare the basic countermeasures for the buildings' safety. Recently, the multiplex buildings which have multi type compounds have increased in size by getting bigger and bigger. As there are many people who would need to escape and the complicated structures like mazes in buildings of this type, it is not only difficult to prevent a fire but also easy to cause a large loss of lives. For a better fire safety supervision of the buildings, there needs to be passers and owners' good sense of safety, fire proof of the buildings and education of the fire authorities.