• Journal of the Optical Society of Korea
• /
• 제16권1호
• /
• pp.63-69
• /
• 2012

This paper presents a method to derive the theoretical requirements for the development of a 400 mm optical window that transmits dual-band wavelengths and had a stable structure. We also present design and fabrication results. Among the required specifications, the surface figure error was defined by the transmitted wavefront deformation (TWD), ${\lambda}$/15 rms at 632.8 nm. This value was derived by estimating the predicted performances with respect to five independent items that could cause system performance degradation and then calculating the required wavefront error (WFE) to satisfy the performance goals. We measured the image resolution at each performance level to trace and verify the requirements. The article also describes a design optimization process that could minimize the weight and volume of the optical window attached to the payload securing the FOV of the camera. In addition, we accurately measured the deformation that occurred in the series of fabrication steps including processing, coating, assembly, bonding and bolting, and investigated the effects by comparing them to the results of a simulation performed in advance to derive the predicted performance.

• 한국정밀공학회지
• /
• 제20권7호
• /
• pp.26-35
• /
• 2003

This study explains the effects of lubricant and surface treatment on hot forging die life. The mechanical and thermal load, and thermal softening which is happened by the high temperature of die, in hot and warm forging, cause die wear, heat checking and plastic deformation, etc. This study is fur the effects of solid lubricants and surface treatment condition for hot forging die. Because cooling effect and low friction are essential to the long life of dies, optimal surface treatment and lubricant are very important to improve die life for hot forging process. The main factors, which affect die hardness and heat transfer, are surface treatments and lubricants, which are related to thermal diffusion coefficient and heat transfer coefficient, etc. For verifying these effects, experiments are performed for hot ring compression test and heat transfer coefficient in various conditions as like different initial billet temperatures and different loads. The effects of lubricant and surface treatment for hot forging die life are explained by their thermal characteristics. The new developed technique in this study for predicting tool life can give more feasible means to improve the tool life in hot forging process.

• 복식
• /
• 제54권3호
• /
• pp.145-158
• /
• 2004

In modern art, body appears as artistic performer, material or producer. and is expressed as' social environment body' which is changed in the relationship with its society and culture. The correlation between body and clothing image appears in 'body as expression object' which directly borrows human body or sets up a section of human body, 'body as medium' in which clothing substitutes body, and 'body as image' in which image of body reappears along with clothing. The results of analysis are as follows : First, 'image of expansion and exaggeration' to expand the influence of clothing thereby disclosing illusion of material civilization prevalent in our society, and make metaphor of dwarfish human's lurking fear by transforming and exaggerating human body. Second, 'image of restriction and suppression' to express the loss of humanity, power and restriction of modern society with fixing and cruelty of body image through clothing which disregard body function. Third, 'image of open and fluidity to criticize the extinction of values of human existence and standardized figure of our society by reducing three-dimensional clothing and body to untypical form or introducing the image of absent of human body to clothing. Fourth, 'image of reversion and paradox' to express practical clothing object with unwearable material, or cause confusion of sex and identity by expressing dual aspects of body at the same time. In this study, which is focused on correlation between body and clothing and the meaning of them, I realized that, even though artistic clothing expressed image of distortion and deformation of human existence as essential subject of body, they, in most contents, were used as medium of communication to rediscover human dignity and identity, and consisted of a series of metaphoric network of meanings satirizing aspects of our society.

• Geomechanics and Engineering
• /
• 제24권6호
• /
• pp.519-529
• /
• 2021

In coal mining activities, the abutment stress of the coal has to undergo cyclic loading and unloading, affecting the strength and seepage characteristics of coal; additionally, it can cause dynamic disasters, posing a major challenge for the safety of coal mine production. To improve the understanding of the dynamic disaster mechanism of gas outburst and rock burst coupling, triaxial devices are applied to axial pressure cyclic loading-unloading tests under different axial stress peaks and different pore pressures. The existing empirical formula is use to perform a non-linear regression fitting on the relationship between stress and permeability, and the damage rate of permeability is introduced to analyze the change in permeability. The results show that the permeability curve obtained had "memory", and the peak stress was lower than the conventional loading path. The permeability curve and the volume strain curve show a clear symmetrical relationship, being the former in the form of a negative power function. Owing to the influence of irreversible deformation, the permeability difference and the damage of permeability mainly occur in the initial stage of loading-unloading, and both decrease as the number of cycles of loading-unloading increase. At the end of the first cycle and the second cycle, the permeability decreased in the range of 5.777 - 8.421 % and 4.311-8.713 %, respectively. The permeability decreases with an increase in the axial stress peak, and the damage rate shows the opposite trend. Under the same conditions, the permeability of methane is always lower than that of helium, and it shows a V-shape change trend with increasing methane pressures, and the permeability of the specimen was 3 MPa > 1 MPa > 2 MPa.

• 한국해양공학회지
• /
• 제34권6호
• /
• pp.436-441
• /
• 2020

Wave field changes resulting from artificial coastal structures constructed in coastal zones have emerged as a major cause of beach erosion, among other factors. The rates of erosion along the eastern coast of Korea have varied mainly owing to the construction of various ports and coastal structures; however, impact assessments of these structures on beach erosion have not been appropriately conducted. Thus, in this study, a methodology to assess the impact of erosion owing to the construction of artificial structures has been proposed, for which a parabolic bay shape equation is used in determining the shoreline angle deformation caused by the structures. Assuming that the conditions of sediment or waves have similar values in most coastal areas, a primary variable impacting coastal sediment transport is the deformation of an equilibrium shoreline relative to the existing beach. Therefore, the angle rotation deforming the equilibrium of a shoreline can be the criterion for evaluating beach erosion incurred through the construction of artificial structures. The evaluation criteria are classified into three levels: safety, caution, and danger. If the angle rotation of the equilibrium shoreline is 0.1° or less, the beach distance was considered to be safe in the present study; however, if this angle is 0.35° or higher, the beach distance is considered to be in a state of danger. Furthermore, in this study, the distance affected by beach erosion is calculated in areas of the eastern coast where artificial structures, mainly including ports and power plants, were constructed; thereafter, an impact assessment of the beach erosion around these areas was conducted. Using a proposed methodology, Gungchon Port was evaluated with caution, whereas Donghae Port, Sokcho Port, and Samcheok LNG were evaluated as being in a state of danger.

• 한국생산제조학회지
• /
• 제22권4호
• /
• pp.686-692
• /
• 2013

Today, environmental issues have become a matter of worldwide concern. In particular, automobile industries engage in considerable research and investment to develop high-efficiency and ecofriendly cars. Most ecofriendly cars use natural gas or hydrogen gas instead of fossil fuels. In this regard, low-weight and high-pressure vessels have gradually been developed to increase the driving distance of a car. However, most pressure vessels installed in cars develop many defects over time owing to shocks sustained when the car is being driven. Such defects can cause the explosion of the pressure vessel. Therefore it is important to prevent such explosions due to internal defects. The use of shearography for measuring the internal defects of objects afford many advantages. It is a non-contact and non-destructive method, and it is not limited by the object shape. In this study, the internal defect deformation and strain of an aluminum liner that is used in a CNG bus for the fuel storage tank is measured using shearography. It is important to measure the strain and deformation in order to detect defects and repair the pressure vessel. To verify the accuracy of the shearography measurement method, the measurement results of shearography, out-of-plane ESPI, and FEM are compared quantitatively.

• Geomechanics and Engineering
• /
• 제38권4호
• /
• pp.381-395
• /
• 2024

With the wide application of urban subway tunnels, the foundation pits of new stations and existing subway tunnels are becoming increasingly close, and even zero-distance close-fitting construction has taken place. To optimize the construction support scheme, the existing tunnel's vertical displacement is theoretically analyzed using the two-stage analysis method to understand the action mechanism of the construction of zero-distance deep large foundation pits on both sides of the existing stations; a three-dimensional numerical calculation is also performed for further analysis. First, the additional stress field on the existing tunnel caused by the unloading of zero-distance foundation pits on both sides of the tunnel is derived based on the Mindlin stress solution of a semi-infinite elastic body under internal load. Then, considering the existing subway tunnel's joints, shear stiffness, and shear soil deformation effect, the tunnel is regarded as a Timoshenko beam placed on the Kerr foundation; a sixth-order differential control equation of the tunnel under the action of additional stress is subsequently established for solving the vertical displacement of the tunnel. These theoretical calculation results are then compared with the numerical simulation results and monitoring data. Finally, an optimized foundation pit support scheme is obtained considering the pit corner effect and external corner failure mode. The research shows a high consistency between the monitoring data,analytical and numerical solution, and the closer the tunnel is to the foundation pit, the more uplift deformation will occur. The internal corner of the foundation pit can restrain the deformation of the tunnel and the retaining structure, while the external corner can cause local stress concentration on the diaphragm wall. The proposed optimization scheme can effectively reduce construction costs while meeting the safety requirements of foundation pit support structures.

• 비파괴검사학회지
• /
• 제34권1호
• /
• pp.18-22
• /
• 2014

용접 잔류응력은 용접공정에서 발생하는 하는데, 용접 구조물의 결함 유발 및 파괴의 주요 원인이 된다. 본 논문에서는 전자 처리 레이저 스페클 간섭법을 이용하여 원전 배관의 용접부 잔류응력을 측정하였다. 인장시험기를 이용하여 용접된 배관에 압축 하중을 가하였으며, 면내 변형 측정 간섭계를 이용하여 용접부와 모재부의 변형을 측정하였고, 제안된 수식에 의하여 탄성계수를 측정하였다. 용접 배관에 가해지는 하중에 따라 변형이 일정하게 증가하며, 용접 배관의 모재부와 용접부에 발생한 변형을 비교하였을 때, 모재부의 변형이 더 크게 나타남을 확인할 수 있었다. 용접 배관 모재부의 탄성계수는 202.46 GPa, 용접부의 탄성 계수는 212.14 GPa, 잔류응력은 6.29 MPa로 측정되었다.

• 문화기술의 융합
• /
• 제8권2호
• /
• pp.337-342
• /
• 2022

최근 프린팅 기술은 디스플레이나 연료전지를 포함한 IT 분야에 폭넓게 사용되고 있지만 핵심 부품인 프린터 헤드의 박막을 적층하는 제조공정에서 발생하는 잔류응력 및 열응력으로 인해 기판이 변형되거나 노즐층이 파손되어 잉크가 새거나 원하는 영역으로 토출되지 않는 문제가 발생하고 있다. 따라서 본 논문에서는 보다 견고하고 신뢰할수 있는 구조를 가진 열전사 잉크젯 프린트 헤드 형상을 제안하고자 한다. 기판과 노즐층의 변형을 줄이기 위해 리브, 기둥, 지지벽 및 개별 피드홀과 같은 다양한 형태의 잉크젯 프린트 헤드 구조가 설계되었으며, FEA 해석을 통해 타당성을 검증하였다. 해석 결과 헤드의 최대 응력 및 노즐층 변형이 최소 40~50%로 급격히 감소하였으며 기둥 및 지지벽 형태의 프린터 헤드를 제작하여 노즐층 변형에 의한 균열 및 잉크 누출이 없는 것을 확인하였다. 따라서 제안된 헤드 형상이 정상 방향의 잉크 토출에 기여하며 대면적 프린팅 기술에도 적용될 수 있을 것으로 기대된다.

• 한국해안해양공학회지
• /
• 제16권2호
• /
• pp.75-82
• /
• 2004

본 연구는 상주해빈의 침식현상을 진단하기 위하여 해빈 단면 측량결과 및 저질 조사결과를 기초로 하여 해빈의 천이주행 특성 및 각 단면별 저류표사량을 산정 하여 해빈 보호 대책을 수립하기 위한 기초자료를 제시하고자 한다. 현장관측을 통하여 상주해빈에 침식방지의 기능을 도모하고자 설치한 돌제가 역기능을 나타내고 있음을 알 수 있었다. 이러한 이유는 도류제가 건설된 후 침식이 가속화되어 침식방지의 기능을 위하여 설치한 돌제가 침식방지의 기능보다는 침식을 가속화시키는 것으로 조사되었다. 그리고 Sonu and Beek(1971)가 제시한 해수면상 저류표사량 산정모델이 자연해빈뿐만이 아니라 해안 구조물이 설치된 해빈에도 유용한 모델임을 입증하였다.