• 한국표면공학회지
• /
• 제36권4호
• /
• pp.296-300
• /
• 2003

Extended cylindrical magnetron sputtering system with rotating 600-mm long and 90-mm diameter graphite cathode and pulsed power supply voltage generator were developed and fabricated. Time-dependent Langmuir probe characteristics as well as carbon films thickness were measured. It was shown that ratio of ions flux to carbon atoms flux for pulsed magnetron discharge mode was equal to $\Phi_{i}$ $\Phi$sub C/ = 0.2. It did not depend on the discharge current in the range of $I_{d}$ / = 10∼60 A since both the plasma density and the film deposition rate were found approximately proportional to the discharge current. In spite of this fact carbon film structure was found to be strongly dependent on the discharge current. Grain size increased from 100 nm at $I_{d}$ = 10∼20 A to 500 nm at $I_{d}$ = 40∼60 A. To deposit fine-grained hard nanocrystalline or amorphous carbon coating current regime with $I_{d}$ = 20 A was chosen. Pulsed negative bias voltage ($\tau$= 40 ${\mu}\textrm{s}$, $U_{b}$ = 0∼10 ㎸) synchronized with magnetron discharge pulses was applied to a substrate and voltage of $U_{b}$ = 3.4 ㎸ was shown to be optimum for a hard carbon film deposition. Lower voltages were not sufficient for amorphization of a growing graphite film, while higher voltages led to excessive ion bombardment and effects of recrystalization and graphitization.

• 한국분말재료학회지
• /
• 제28권6호
• /
• pp.497-501
• /
• 2021

Cobalt (Co) is mainly used to prepare cathode materials for lithium-ion batteries (LIBs) and binder metals for WC-Co hard metals. Developing an effective method for recovering Co from WC-Co waste sludge is of immense significance. In this study, Co is extracted from waste cemented carbide soft scrap via mechanochemical milling. The leaching ratio of Co reaches approximately 93%, and the leached solution, from which impurities except nickel are removed by pH titration, exhibits a purity of approximately 97%. The titrated aqueous Co salts are precipitated using oxalic acid and hydroxide precipitation, and the effects of the precipitating agent (oxalic acid and hydroxide) on the cobalt microstructure are investigated. It is confirmed that the type of Co compound and the crystal growth direction change according to the precipitation method, both of which affect the microstructure of the cobalt powders. This novel mechanochemical process is of significant importance for the recovery of Co from waste WC-Co hard metal. The recycled Co can be applied as a cemented carbide binder or a cathode material for lithium secondary batteries.

• 공업화학
• /
• 제33권6호
• /
• pp.618-623
• /
• 2022

분리판은 반응물 및 전자를 전달하고 부산물인 물과 열을 배출하며, 막전극접합체의 지지체 역할을 하는 고분자전해질 연료전지의 핵심 구성요소이다. 따라서 분리판의 유로 구조는 연료전지의 성능을 향상시키는데 중요한 역할을 한다. 본 연구에서는 압축률이 다른 구리 폼을 cathode 분리판에 적용한 25 cm² 단위 전지를 이용하여 성능 평가를 수행하였다. 금속 폼의 압축률이 증가할수록 총 저항이 감소하였으며, 특히 전하전달과 물질전달 저항이 사형 유로에 비해 크게 개선되어 중전류밀도 및 고전류밀도 영역에서 전압 손실을 줄일 수 있었다. 가압한 공기를 사용한 사형 유로 구조의 경우 연료전지의 성능이 압축한 금속 폼(S3)을 적용한 유로와 중전류밀도 영역까지는 큰 차이가 없었으나, 고전류밀도 영역에서는 유로 구조의 한계로 낮은 성능을 보였다.

• 한국건설순환자원학회논문집
• /
• 제10권1호
• /
• pp.66-73
• /
• 2022

동절기 콘크리트 포장체의 블랙아이스 발생위험을 낮추고 동결에 의한손상을 방지할 목적으로 콘크리트의 전도저항성을 활용하여 자기 히팅 콘크리트를 개발하고자 하였다. 이를 위하여 분말형과 액상형 폐CNT와 전도촉진을 위해 폐음극재를 사용하여 강도변화와 온도 발열특성을 평가하고자 하였다. 액상형 폐CNT가 모르타르내에서 분산정도가 효과적이고, 강도저하가 작게 발생하는 것으로 분석되었다. 또한 모르타르에 스틸매쉬, 구리포일과 구리선을 전극으로 적용하여 DC 24 V를 공급하였으며, 폐CNT, 폐음극재과 탄소섬유 혼입율에 따른 온도변화 특성을 평가하였다. 또한 선정된 최적배합으로부터 전극간격에 따른 온도 특성을 평가하여 AC 50 V 까지는 전극간격 100 mm 까지는 충분한 발열 특성을 갖는 것을 확인하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권7호
• /
• pp.881-890
• /
• 2011

Analyses of performance and behavior of the individual PEM fuel cells (PEMFC) under different operating conditions are of importance optimally to design and efficiently to operate the stack. The paper focuses on experimental analyses of a two-cell stack under different operating conditions, which performance and behavior are measured by the voltage of a cell as well as the stack. Experimental parameters include stoichiometric ratio, temperature of the air supplied under different working stack temperatures and loads. Results showed that the cell voltages are dominantly influenced by the temperature of the air supplied among others. In addition, an inherent difference between the first and the second cell voltage exists because of the tolerances of the cell components and the resulting different over-potentials at different equilibrium states. Furthermore, it is shown that the proton conductivity in the membranes conditioned by the humidity in the cathode channel highly affects the voltage differences of the two cells.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.87.2-87.2
• /
• 2010

The steady and dynamic process model for an internal reforming molten carbonate fuel cell power plant is discussed in this paper. The dominant thermal and chemical dynamic processes are modeled for the stack module and balance-of-plant, including cathode gas preparation, heat recovery, heat loss (Each heat loss amount for the stack and MBOP is obtained from real plant data) and fuel processing. Based on dynamic model and control demand, PID controllers are designed in the whole system. By applying these controllers we can obtain temperature balance of stack and control system depending on changing steam to carbon ratio, air feed amount, and transient condition.

• 한국생산제조학회지
• /
• 제21권4호
• /
• pp.547-555
• /
• 2012

This paper focuses on the research of the anode and cathode in the Ni-MH secondary battery. In this paper, the proposed method employs a continuous wave Nd : YAG laser based on the pure Ni instead of the low carbon steel to improve the conductivity although the conventional secondary battery is based on the resistance spot welded with low carbon steel SS41. It welds a sandwich panel using the pure Ni and the porous thin plate, and the tested optimal conditions for the laser power and irradiation speed were 300 and 350 Watt, and 1.0~1.6m/min, respectively. Finally, we observed a ratio, heat input and cross-section and measured the conductivity of the welding section to test the weldability.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 춘계학술대회 및 기술 세미나 논문집 디스플레이 광소자
• /
• pp.55-56
• /
• 2008

The photo leakage currents of a conventional hydrogenated amorphous silicon(a-Si:H) thin film transistor(TFT) were investigated and analyzed in the case of illumination from various lightsources such as halogen lamp, cold cathode fluorescent lamp(CCFL) backlight, and white light emitting diode(LED) backlight The photo leakage characteristics showed the apparent differences in the leakage level and in the $I_{on}/I_{off}$ ratio in spite of the similar luminances of light sources. This leakage level is expected to be related to the wavelength of the lowest intensity peak from spectral analysis of light sources.

• Transactions on Electrical and Electronic Materials
• /
• 제14권1호
• /
• pp.28-31
• /
• 2013

A volcano shaped gated Si-FEA (silicon field emitter array) was simply fabricated using sputtering as a gate electrode deposition and lift-off for the removal of the oxide mask, respectively. Due to the limited step coverage of well-controlled sputtering and the high aspect ratio in Si dry etch caused by high RF power, it was possible to obtain Si FEAs with a stable volcano shaped gate structure and to realize the restriction of gate leakage current in field emission characteristics. For 100 tip arrays and 625 tip arrays, gate leakage currents were restricted to less than 1% of the anode current in spite of the volcano-shaped gate structure. It was also possible to keep the emitters stable without any failure between the Si cathode and gate electrode in field emission for a long time.

• 한국전산유체공학회지
• /
• 제12권3호
• /
• pp.41-46
• /
• 2007

Dynamic behavior of immiscible gas bubble attached to the wall in channel flow plays very important role in many engineering applications. Special attention has been paid to micro direct methanol fuel cell(${\mu}$DMFC) where surface tension becomes dominant factor with minor gravitational effect due to its reduced size. Therefore, displacement of $CO_2$ bubble generating on a cathode side in ${\mu}$DMFC can be very difficult and efficient removal of $CO_2$ bubbles will affect the overall machine performance considerably. We have focused our efforts on studying the dynamic behavior of immiscible bubble attached to the one side of the wall on 2D rectangular channel subject to external shear flow. We used Level Contour Reconstruction Method(LCRM) which is the simplified version of front tracking method to track the bubble interface motion. Effects of Reynolds number, Weber number, advancing/receding contact angle and property ratio on bubble detachment characteristic has been numerically identified.