• Korean Chemical Engineering Research
• /
• 제49권6호
• /
• pp.775-780
• /
• 2011

50 $cm^2$의 활성면적을 가진 셀을 이용하여 5-셀 DMFC 스택을 제작하고 4 A의 부하로 4,000 시간 운전한 후 성능감소 및 성능 감소 원인을 분석하였다. 4,000 시간 운전 후 10 A에서 스택의 전력 밀도가 28.7% 감소하였으며 다섯개의 셀 중 두 개는 거의 성능저하가 일어나지 않았고 두 개는 약 40%의 성능 저하, 한 개는 약 60%의 성능 저하를 보였으며 각 셀별 성능저하의 정도의 차이는 스택 내에서의 위치와 상관관계가 없었다. 스택 내의 다섯 셀 중 가장 성능감소가 심하였던 셀의 경우 연료극 촉매층의 Pt 입자 크기가 증가하였으며 연료가 들어가는 쪽의 Pt 입자의 크기 증가가 더 심하였다. 그러나 4,000 시간 장기운전 후 공기극 촉매층에서는 Pt 입자 크기의 변화는 거의 없었다. 스택 내의 모든 셀에서 4,000 시간 운전 후 연료극 촉매에서 공기극 촉매로의 루테늄의 크로스오버가 SEM-EDX로 관찰되었으며 특히 성능감소가 심하였던 셀의 경우 공기극 촉매층에서 Ru/Pt의 비율이 가장 컸다.

• 한국세라믹학회지
• /
• 제39권4호
• /
• pp.359-366
• /
• 2002

고체산화물 연료전지의 운전온도를 낮추기 위해 구성재 중 LSGM 전해질과 LSM 양극을 합성하고, 그 특성을 조사한 후 최적 조성과 공정으로 단위전지를 제작하고 출력을 측정하였다. 전해질 조성인 $(La_{0.85}Sr_{0.15})(Ga_{0.8}Mg_{0.2})O_{3-\delta}와 (La_{0.8}Sr_{0.2})(Ga_{0.8}Mg_{0.2})O_{3-\delta}$를 $1500^{\circ}$에서 6시간 소결한 경우 두 조성 모두 $LaGaO_3$의 단일상을 형성하였고, $10∼3{\mu}m$의 결정 크기를 갖는 치밀한 미세구조를 얻었으며, 저기전도도는 $800^{\circ}$에서 0.13S/cm를 나타내었다. 양극의 경우 GNP법으로 $(La1-xSrx)MnO_3$를 합성한 경우 Sr의 양이 0.2mole일 때까지는 $LaMnO_3$ perovskite 단일상이 생성되었으며, 입자의 크기는 약 40nm였다. 단위전지는 $(La_{0.8}Sr_{0.2})(Ga_{0.8}Mg_{0.2})O_{3-\delta}$ 조성으로 소결한 전해질 양면에 $(La_{0.9}Sr_{0.1})MnO_3$ 양극과 음극의 입자크기는 $1{\mu}m$ 정도였고 다공성을 나타내었다. 이때 단위전지의 출력은 $800^{\circ}$에서 약 $0.3W/cm^2$를 나타내었다

• 세라미스트
• /
• 제21권4호
• /
• pp.378-387
• /
• 2018

The optimal fabrication conditions for $Gd_{0.1}Ce_{0.9}O_{2-{\delta}}$(GDC) buffer layer and $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_{3-{\delta}}$ (LSCF) cathode on 1mol% $CeO_2-10mol%\;Sc_2O_3$ stabilized $ZrO_2$ (CeScSZ) electrolyte were investigated for application of IT-SOFCs. GDC buffer layer was used in order to prevent undesired chemical reactions between LSCF and CeScSZ. These experiments were carried out with $5{\times}5cm^2$ anode supported unit cells to investigate the tendencies of electrochemical performance, Microstructure development and interface reaction between LSCF/GDC/CeScSZ along with the variations of GDC buffer layer thickness, sintering temperatures of GDC and LSCF were checked, respectively. Electrochemical performance was analyzed by DC current-voltage measurement and AC impedance spectroscopy. Microstructure and interface reaction were investigated by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). Although the interfacial reaction between these materials could not be perfectly inhibited, We found that the cell, in which $6{\mu}m$ GDC interlayer sintered at $1200^{\circ}C$ and LSCF sintered at $1000^{\circ}C$ were applied, showed good interfacial adhesions and effective suppression of Sr, thereby resulting in fairly good performance with power density of $0.71W/cm^2$ at $800^{\circ}C$ and 0.7V.

• Transactions on Electrical and Electronic Materials
• /
• 제17권3호
• /
• pp.139-142
• /
• 2016

β-AgVO₃ nanorods have been successfully synthesized using a soft chemistry route followed by heat treatment. They were characterized by X-ray diffraction and field emission scanning electron microscopy, and their electrochemical properties were investigated using cyclic voltammetry, impedance spectra, and charge-discharge tests. The results showed that the smooth-surfaced nanorods are very uniform and well dispersed, with diameters of ~100-200 nm and lengths of the order of several macrometers. The nanorods deliver a maximum specific discharge capacity of 275 mAh g^-1 at 30 mA g^-1. They also demonstrated good rate capability with a discharge capacity at the 100^th cycle of 51 mAh g^-1.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.87.2-87.2
• /
• 2010

The steady and dynamic process model for an internal reforming molten carbonate fuel cell power plant is discussed in this paper. The dominant thermal and chemical dynamic processes are modeled for the stack module and balance-of-plant, including cathode gas preparation, heat recovery, heat loss (Each heat loss amount for the stack and MBOP is obtained from real plant data) and fuel processing. Based on dynamic model and control demand, PID controllers are designed in the whole system. By applying these controllers we can obtain temperature balance of stack and control system depending on changing steam to carbon ratio, air feed amount, and transient condition.

• 한국생산제조학회지
• /
• 제21권4호
• /
• pp.547-555
• /
• 2012

This paper focuses on the research of the anode and cathode in the Ni-MH secondary battery. In this paper, the proposed method employs a continuous wave Nd : YAG laser based on the pure Ni instead of the low carbon steel to improve the conductivity although the conventional secondary battery is based on the resistance spot welded with low carbon steel SS41. It welds a sandwich panel using the pure Ni and the porous thin plate, and the tested optimal conditions for the laser power and irradiation speed were 300 and 350 Watt, and 1.0~1.6m/min, respectively. Finally, we observed a ratio, heat input and cross-section and measured the conductivity of the welding section to test the weldability.

• 디지털산업정보학회논문지
• /
• 제4권4호
• /
• pp.21-29
• /
• 2008

The DC characteristics of GaAS Gunn diode are investigated as a preliminary study on the planar grade gap injector GaAs Gunn diode which is the transferred electron device with high output power and dc-rf conversion efficiency. The Gunn devices we fabricated were confirmed to have the DC characteristics of negative differential resistance(NDR). We discussed the nature of the NDR effect, including the electron intervalley transfer; the NDR effect was examined for six different cathode radii.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1991년도 하계학술대회 논문집
• /
• pp.3-12
• /
• 1991

Fuel cells are electrochemical devices that convert the chemical reaction energy directly into the electrical energy. In a typical fuel cell, gaseous fuel is fed continuously to the anode(negative electrode) compartment and the oxidant(i.e, oxygen from air) is fed continuously to the cathode(positive electrode) compartment; the electrochemical reactions take place at the electrodes to produce an electric current. Many of the operational characteristics of fuel cell systems are superior to those of conventional power generation system because of good efficiency, environmental protection, safty, modularity etc. From those reasons, the fuel cells are considered to be the solution to the future problem of energy conversion. The objective of this paper is to introduce the technical status of fuel cell technologies and our national project for the development of the phosporic acid fuel cell.

• Transactions on Electrical and Electronic Materials
• /
• 제14권1호
• /
• pp.28-31
• /
• 2013

A volcano shaped gated Si-FEA (silicon field emitter array) was simply fabricated using sputtering as a gate electrode deposition and lift-off for the removal of the oxide mask, respectively. Due to the limited step coverage of well-controlled sputtering and the high aspect ratio in Si dry etch caused by high RF power, it was possible to obtain Si FEAs with a stable volcano shaped gate structure and to realize the restriction of gate leakage current in field emission characteristics. For 100 tip arrays and 625 tip arrays, gate leakage currents were restricted to less than 1% of the anode current in spite of the volcano-shaped gate structure. It was also possible to keep the emitters stable without any failure between the Si cathode and gate electrode in field emission for a long time.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2009년도 추계학술대회 논문집
• /
• pp.69-72
• /
• 2009

Recently, LED(Light Emitting Diode) TV has attracted greate attention due to its super-slim form factore as well as low power consumption. LED TV is actually an LCD(Liquid Crystal Display) TV in which edge-lit LED backlight is adopted. In the presente study, we report on the comparison of optical characteristics 55-inch edge-lit LED backlight and CCFL(Cold Cathode Fluorescent Lam)backlight. The angular distribution of the luminance and the on-axis luminance gain on each optical component were investigated and compared. The effect of the backlight structure on the performance of the optical films was studied and discussed.