• Korean Journal of Materials Research
• /
• v.16 no.4
• /
• pp.253-256
• /
• 2006

The blue emitting OLEDs using GDI host-dopant phosphors have been fabricated and characterized. In the device fabrication, 2-TNATA [4,4',4'-tris(2-naphthylphenyl-phenylamino)- triphenylamine] as a hole injection material and NPB [N,N'-bis(1-naphthyl)-N,N'-diphenyl-1,1'-biphenyl-4,4'-diamine] as a hole transport material were deposited on the ITO(indium thin oxide)/glass substrate by vacuum evaporation. And then, blue color emission layer was deposited using GDI602 as a host material and GDI691 as a dopant. Finally, small molecule OLEDs with structure of ITO/2-TNATA/NPB/GDI602:GDI691/Alq3/LiF/Al were obtained by in-situ deposition of Alq3, LiF and Al as the electron transport material, electron injection material and cathode, respectively. Blue OLEDs fabricated in our experiments showed the color coordinate of CIE(0.14, 0.16) and the maximum power efficiency of 1.1 lm/W at 11 V with the peak emission wavelength of 464 nm.

• Journal of IKEEE
• /
• v.19 no.4
• /
• pp.535-540
• /
• 2015

A microstrip gas chamber (MSGC), applied to digital radiography system, was designed and constructed. The microstrip electrodes were fabricated with Chrome(Cr.). by photolithography process on Silicon(Si) wafer and glass substrate. The width of anode and cathode electrodes was $10{\mu}m$, and $290{\mu}m$, respectively. The distance of the electrodes was $100{\mu}m$, and the active area was $50{\times}50mm^2$. And the number of anode was 80. The microstrip electrodes were damaged when discharges occurred over the 600 V of anode voltage. As the result of experiments. It detected the typical output signals of the pulse width, 20 ns, under the condition that the detecting gas was Ar(90%) + $CH_4$(10%), X-ray tube voltage was 42 kV, and tube current was 1 mA.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.29.1-29.1
• /
• 2009

Fabrication of good quality P-type GaN remained as a challenge for many years which hindered the III-V nitrides from yielding visible light emitting devices. Firstly Amano et al succeeded in obtaining P-type GaN films using Mg doping and post Low Energy Electron Beam Irradiation (LEEBI) treatment. However only few region of the P-GaN was activated by LEEBI treatment. Later Nakamura et al succeeded in producing good quality P-GaN by thermal annealing method in which the as deposited P-GaN samples were annealed in N2 ambient at temperatures above $600^{\circ}C$. The carrier concentration of N type and P-type GaN differs by one order which have a major effect in AlGaN based deep UV-LED fabrication. So increasing the P-type GaN concentration becomes necessary. In this study we have proposed a novel method of activating P-type GaN by electrochemical potentiostatic method. Hydrogen bond in the Mg-H complexes of the P-type GaN is removed by electrochemical reaction using KOH solution as an electrolyte solution. Full structure LED sample grown by MOCVD serves as anode and platinum electrode serves as cathode. Experiments are performed by varying KOH concentration, process time and applied voltage. Secondary Ion Mass Spectroscopy (SIMS) analysis is performed to determine the hydrogen concentration in the P-GaN sample activated by annealing and electrochemical method. Results suggest that the hydrogen concentration is lesser in P-GaN sample activated by electrochemical method than conventional annealing method. The output power of the LED is also enhanced for full structure samples with electrochemical activated P-GaN. Thus we propose an efficient method for P-GaN activation by electrochemical reaction. 30% improvement in light output is obtained by electrochemical activation method.

• Korean Journal of Materials Research
• /
• v.18 no.4
• /
• pp.199-203
• /
• 2008

High-efficiency phosphorescent organic light emitting diodes using TCTA-TAZ as a double host and $Ir(ppy)_3$ as a dopant were fabricated and their electro-luminescence properties were evaluated. The fabricated devices have the multi-layered organic structure of 2-TNATA/NPB/(TCTA-TAZ) : $Ir(ppy)_3$/BCP/SFC137 between an anode of ITO and a cathode of LiF/AL. In the device structure, 2-TNATA[4,4',4"-tris(2-naphthylphenyl-phenylamino)-triphenylamine] and NPB[N,N'-bis(1-naphthyl)-N,N'-diphenyl-1,1'-biphenyl-4,4'-diamine] were used as a hole injection layer and a hole transport layer, respectively. BCP [2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline] was introduced as a hole blocking layer and an electron transport layer, respectively. TCTA [4,4',4"-tris(N-carbazolyl)-triphenylamine] and TAZ [3-phenyl-4-(1-naphthyl)-5-phenyl-1,2,4-triazole] were sequentially deposited, forming a double host doped with $Ir(ppy)_3$ in the [TCTA-TAZ] : $Ir(ppy)_3$ region. Among devices with different thickness combinations of TCTA ($50\;{\AA}-200\;{\AA}$) and TAZ ($100\;{\AA}-250\;{\AA}$) within the confines of the total host thickness of $300\;{\AA}$ and an $Ir(ppy)_3$-doping concentration of 7%, the best electroluminescence characteristics were obtained in a device with $100\;{\AA}$-think TCTA and $200\;{\AA}$-thick TAZ. The $Ir(ppy)_3$ concentration in the doping range of 4%-10% in devices with an emissive layer of [TCTA ($100\;{\AA}$)-TAZ ($200\;{\AA}$)] : $Ir(ppy)_3$ gave rise to little difference in the luminance and current efficiency.

• Korean Journal of Materials Research
• /
• v.28 no.11
• /
• pp.646-652
• /
• 2018

During a long-term operation of polymer electrolyte membrane fuel cells(PEMFCs), the fuel cell performance may degrade due to severe agglomeration and dissolution of metal nanoparticles in the cathode. To enhance the electrochemical durability of metal catalysts and to prevent the particle agglomeration in PEMFC operation, this paper proposes a hybrid catalyst structure composed of PtCo alloy nanoparticles encapsulated by porous carbon layers. In the hybrid catalyst structure, the dissolution and migration of PtCo nanoparticles can be effectively prevented by protective carbon shells. In addition, $O_2$ can properly penetrate the porous carbon layers and react on the active Pt surface, which ensures high catalytic activity for the oxygen reduction reaction. Although the hybrid catalyst has a much smaller active surface area due to the carbon encapsulation compared to a commercial Pt catalyst without a carbon layer, it has a much higher specific activity and significantly improved durability than the Pt catalyst. Therefore, it is expected that the designed hybrid catalyst concept will provide an interesting strategy for development of high-performance fuel cell catalysts.

• Korean Journal of Materials Research
• /
• v.32 no.4
• /
• pp.210-215
• /
• 2022

Extensive research is being carried out on Ni-rich Li(Ni_xCo_yMn_1-x-y)O₂ (NCM) due to the growing demand for electric vehicles and reduced cost. In particular, Ni-rich Li(Ni_xCo_yMn_1-x-y-zAl_z)O₂ (NCMA) is attracting great attention as a promising candidate for the rapid development of Co-free but electrochemically more stable cathodes. Al, an inactive element in the structure, helps to improve structural stability and is also used as a doping element to improve cycle capability in Ni-rich NCM. In this study, NCMA was successfully synthesized with the desired composition by direct coprecipitation. Boron and tin were also used as dopants to improve the battery performance. Macro- and microstructures in the cathodes were examined by microscopy and X-ray diffraction. While Sn was not successfully doped into NCMA, boron could be doped into NCMA, leading to changes in its physicochemical properties. NCMA doped with boron revealed substantially improved electrochemical properties in terms of capacity retention and rate capability compared to the undoped NCMA.

• Applied Chemistry for Engineering
• /
• v.34 no.6
• /
• pp.567-575
• /
• 2023

Water electrolysis is undergoing active research as one of the promising technologies for producing effective green hydrogen. Using seawater directly as a raw material for a water electrolysis system can solve the problem of the limitations of existing freshwater raw materials, as seawater accounts for approximately 97% of the water on Earth. At the same time, abundant by-product materials can be obtained, representative examples of which are Cl₂, ClO^-, Br₂, and Mg(OH)₂ produced during electrolysis, depending on their composition and pH environment. In order to develop a successful seawater electrolysis system and oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) catalysts, it is necessary to understand the causes and consequences of reactions that occur in the seawater environment. Therefore, in this paper, we will investigate the reaction mechanism and characteristics of the seawater electrolysis system as well as the research and development trends of electrochemical catalysts used in anode and cathode electrodes.

• Journal of the Korean Ceramic Society
• /
• v.39 no.10
• /
• pp.928-934
• /
• 2002

Gallium doped Zinc Oxide(GZO) films were deposited by dc magnetron sputtering using a GZO ceramic target at various conditions such as substrate temperature (RT, 400), residual water pressure ($P_{H_2O}$; 1.61${\times}10^{-4}∼2.2{\times}10^{-3}$ Pa), introduction of $H_2$ gas (8.5%) and different magnetic field strengths(250, 1000G). GZO films deposited without substrate heating showed clear degradation in film crystallinity and electrical properties with increasing $P_{H_2O}$. The resistivity increased from 3.0${\times}10^{-3}$ to 3.1${\times}10^{-2}{\Omega}㎝$ and the grain size of the films decreased from 24 to 3 nm when PH2O was increased from 1.61${\times}10^{-4}$ to 2.2${\times}10^{-3}$ Pa. However, degradation in electrical properties with increasing $P_{H_2O}$ was not observed for the films deposited with introduction of 8.5% $H_2$. When magnetic field strength of the cathode increased from 250G to 1000G, crystallinity and electrical properties of GZO films improved remarkably about all the $P_{H_2O}$. This result could be attributed to the decrease in film damage caused by the decrease in plasma impedance.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.4
• /
• pp.59-64
• /
• 2008

In this paper, white polymer light emitting diodes(WPLEDs) were fabricated and investigated the electrical and optical properties for the prepared devices. ITO(indium tin oxide) and PEDOT:PSS [poly(3,4-ethylenedioxythiophene):poly(styrene sulfolnate)] as anode and hole injection materials, PFO [poly(9,9-dioctylfluorene)] and MEH-PPV [poly(2-methoxy-5(2-ethylhe xoxy)-1,4-phenylenevinyle)] were used as the light emitting host and guest materials, respectively. The LiF(lithium flouride) and Al(aluminum) were used electron injection materials and cathode materials. Finally, the WPLED with structure of ITO/PEDOT:PSS/PFO:MEH-PPV/LiF/Al was fabricated. The prepared WPLED showed white emission with CIE coordinates of (x=0.36, y=0.35) at the applied voltage of 9V. The maximum current density and luminance were about $740mA/cm^2\;and\;900cd/m^2$ at 13V, respectively. And the maximum current efficiency was 0.37 cd/A at $200cd/m^2$ in luminance.

• Resources Recycling
• /
• v.31 no.4
• /
• pp.26-33
• /
• 2022

Owing to the demand for lithium-ion batteries, the recovery of valuable metals from waste lithium-ion batteries is required in future. A pyrometallurgical treatment is appropriate for recycling a large number of waste lithium-ion batteries, but Li loss to slag and dust present a significant challenge. This research investigated carbonation roasting and water leaching behaviors in Li-ion batteries by graphite addition to recover Li from the NCM-based cathode materials of waste Li-ion batteries. When 10 wt% of graphite was added, CO and CO₂ gases were emitted with a rapid weight reduction at apporoximately 850 K, when heated in Ar and CO₂ atmosphere. After the rapid weight reduction, NCM was decomposed and reduced to metal oxides and pure metals. In the carbonation roasting of black powder (NCM+graphite), O₂ is generated via the decomposition of NCM, and an oxides, such as Li₂O and NiO were were also generated. Subsequently, Li₂O reacts with CO₂ to generate Li₂CO₃, and a part of NiO was reduced by graphite to produce metal Ni. In addition, up to 94.5 % Li₂CO₃ with ~99.95 % purity was recovered via water leaching after carbonation roasting.