• International Journal of Precision Engineering and Manufacturing
• /
• 제1권2호
• /
• pp.61-66
• /
• 2000

In this paper, we discuss the machining characteristics of HDD glass. Glass is now being used globally as a data storage device, Such glasses are usually machined by lapping by this technique requires a long machining time, resulting in low productivity, For this reason, we examine the possibility of EILD grinding in HDD glass workpieces, A move to ELID grinding may result in substantial cost reduction. Our purpose is to investigate the grinding characteristics of HDD glass in ELID grinding. The bonding materials for fixing the abrasives of cast iron, cobalt and bronze are applied, and grinding conditions such as rotation speed and feeding are varied. Results show that with the use of ELID, mirror surfaces can be achieved with high efficiency.

• Structural Engineering and Mechanics
• /
• 제37권2호
• /
• pp.177-196
• /
• 2011

An economic, structurally effective and practically applicable strengthening technique was developed for reinforced concrete (RC) framed buildings. The idea of the technique is to convert the existing hollow brick infill wall into a load carrying system acting as a cast-in-place RC infill wall by bonding relatively thin high strength precast concrete PC panels to the plastered hollow brick infill. For this purpose, a total of eight one-third scale, one bay, one story frames were tested under reversed-cyclic lateral loads. Test frames were designed and constructed with common deficiencies observed in practice. Four different panel types were used for strengthening. Test results showed that both strength and stiffness of the frames were significantly improved by the introduction of PC panels. Experimental results were compared with the analytical approaches suggested by the authors.

• Computers and Concrete
• /
• 제23권3호
• /
• pp.155-160
• /
• 2019

The use of recycled aggregate concrete for the purpose of environmental and resource conservation has gained increasing interest in construction engineering. Nevertheless, few studies have reported on the bonding performance of the bars in recycled aggregate concrete after exposed to high temperatures. In this paper, 72 pull-out specimens and 36 cubic specimens with different recycled coarse aggregate content (i.e., 0%, 50%,100%) were cast to evaluate the bond behavior between recycled aggregate concrete and steel bar after various temperatures ($20^{\circ}C$, $200^{\circ}C$, $400^{\circ}C$, $600^{\circ}C$). The results show that the recycled aggregate concrete pull-out specimens exhibited similar bond stress-slip curves at both ambient and high temperature. The bond strength declined gradually with the increase of the temperature. On the basis of a regression analysis of the experimental data, a revised bond strength mode and peak slip ratios relationship model were proposed to predict the post-heating bond-slip behavior between recycled aggregate concrete and steel bar.

• 공업화학
• /
• 제9권2호
• /
• pp.185-192
• /
• 1998

네 종류의 폴리아믹산(PPA)은 서로 다른 구조의 디아민들인 3,3'-diaminodiphenyl sulfone(3,3'-$DDSO_2$), 4,4'-diarrinodiphenyl sulfone(4,4'-$DDSO_2$), 4,4'-methylene dianiline(4,4'-MDA) 및 4,4'-oxydianiline(4,4'-ODA)와 디안하이드라이드인 3,3', 4,4'-benzophenone tetracarboxylic dianhydride (BTDA)를 용매인 DMAc를 이용하여 합성되었다. 이들의 폴리아믹산(PAA)을 이용하여 poly[2,2-(m-phenylene)-5,5'-bibenzimidazole](PBI)와 용액 블렌딩하여 Blend-I, II, III, 그리고 IV로 칭하였으며, 이에 대한 시료를 필름이나 분말로 제조한 PBI/PAA 시스템을 예상된 $T_g$보다 높은 온도에서 열경화시켜 PBI/PI 블렌드로 전환시킨후 PI 합성시 사용된 디아민의 분자구조 변화에 따른 블렌드의 상용성과 그 상호작용의 상대적인 세기를 살폈다. 이로부터 본 연구에서 이용된 네 개의 블렌드들은 상용성을 보였으며, 이들 상용성을 가져다주는 상호작용의 세기는 Blend-III와 Blend-IV가 Blend-I와 Blend-II보다 큼을 보였다. 이와 같이 블렌드에 사용된 PI의 구조변화에 따라 상호작용이 다른 것은 PI합성시에 사용된 디아민의 구조에서 페닐링 사이에 존재하는 linkage인 O나 $CH_2$보다는 $SO_2$가 존재할 때 블렌드를 이루는 두 고분자사이의 상호작용인 수소결합력을 약화시키는 spacer로 작용하였다고 판단된다.

• 대한의생명과학회지
• /
• 제14권2호
• /
• pp.105-113
• /
• 2008

The objective of this study was to evaluate the influence of surface modifications on the bonding characteristics and cytotoxicity of specific titanium porcelain bonded to milling titanium and cast titanium. Milling titanium and cast titanium samples were divided into 8 test groups. These groups are as follow: i) sandblasted with particles of different size of $220{\mu}m\;and\;50{\mu}m$, ii) different sequences of sandblasting treatment and etching treatment, iii) etched with different etching solutions, and iv) preheated or not. The surface characteristics of specimens were characterized by the test of mean roughness of surface and SEM. The bond strength of titanium-ceramic systems was measured by using three-point bending test and SEM. The results show that the mean roughness of surface of sample sandblasted with $220{\mu}m$ aluminum oxide increased and bond strength were higher than sample sandblasted with $50{\mu}m$ aluminum oxide. The mean roughness of surface decreased, but the bond strength increased when the samples sandblasted with $220{\mu}m$ aluminum oxide were preheated. The sample sandblasted with $220{\mu}m$ aluminum oxide after oxidized with occupational corrosive agent I (50% NaOH, 10% $CuSO_4{\cdot}5H_2O$) and II (35% $HNO_3$, 5% HF) showed higher bond strength than sample oxidized with 30% $HNO_3$ after sandblasted with $220{\mu}m$ aluminum oxide. Group NaCuNF220SP (milling Ti: 35.3985 MPa, casting Ti: 37.2306 MPa) which was treated with occupational corrosive agent I (50% NaOH, 10% $CuSO_4{\cdot}5H_2O$) and II (35% $HNO_3$, 5% HF), followed by sandblasting with $220{\mu}m$ aluminum oxide and preheating at $750^{\circ}C$ for 1 hour showed the highest bond strength and significant differences (P<0.05). The method for modifying surface of titanium showed excellent stability of cells.

• The Journal of Advanced Prosthodontics
• /
• 제6권4호
• /
• pp.317-324
• /
• 2014

PURPOSE. This study was to evaluate the effect of grinding of the inner metal surface during the porcelain try-in stage on metal-porcelain bonding considering the maximum temperature and the vibration of samples. MATERIALS AND METHODS. Ninety-one square prism-shaped ($1{\times}1{\times}1.5mm$) nickel-chrome cast frameworks 0.3 mm thick were prepared. Porcelain was applied on two opposite outer axial surfaces of the frameworks. The grinding was performed from the opposite axial sides of the inner metal surfaces with a low-speed handpiece with two types of burs (diamond, tungsten-carbide) under three grinding forces (3.5 N, 7 N, 14 N) and at two durations (5 seconds, 10 seconds). The shear bond strength (SBS) test was performed with universal testing machine. Statistical analyzes were performed at 5% significance level. RESULTS. The samples subjected to grinding under 3.5 N showed higher SBS values than those exposed to grinding under 7 N and 14 N (P<.05). SBS values of none of the groups differed from those of the control group (P>.05). The types of bur (P=.965) and the duration (P=.679) did not affect the SBS values. On the other hand, type of bur, force applied, and duration of the grinding affected the maximum temperatures of the samples, whereas the maximum vibration was affected only by the type of bur (P<.05). CONCLUSION. Grinding the inner metal surface did not affect the metal-porcelain bond strength. Although the grinding affected the maximum temperature and the vibration values of the samples, these did not influence the bonding strength.

• Computers and Concrete
• /
• 제24권2호
• /
• pp.159-172
• /
• 2019

This paper presents an investigation into the flexural behavior of reinforced concrete (RC) beams retrofitted by ultra-high performance fiber-reinforced concrete (UHPFRC) layers. The experimental study has been conducted in two parts. In the first part, four methods of retrofitting with UHPFRC layers in both the up and down sides of the beams have been proposed and their efficiency in the bonding of the normal concrete and ultra-high performance fiber-reinforced concrete has been discussed. The results showed that using the grooving method and the pre-casted UHPFRC layers in comparison with the sandblasting method and the cast-in-place UHPFRC layers leads to increase the load carrying capacity and the energy absorption capacity and causes high bond strength between two concretes. In the second part of the experimental study, the tests have been conducted on the beams with single UHPFRC layer in the down side and in the up side, using the effective retrofitting method chosen from the first part. The results are compared with those of non-retrofitted beam and the results of the first part of experimental study. The results showed that the retrofitted beam with two UHPFRC layers in the up and down sides has the highest energy absorption and load carrying capacity. A finite element analysis was applied to prediction the flexural behavior of the composite beams. A good agreement was achieved between the finite element and experimental results. Finally, a parametric study was carried out on full-scale retrofitted beams. The results indicated that in all retrofitted beams with UHPFRC in single and two sides, increasing of the UHPFRC layer thickness causes the load carrying capacity to be increased. Also, increases of the normal concrete compressive strength improved the cracking load of the beams.

• 화약ㆍ발파
• /
• 제38권4호
• /
• pp.46-52
• /
• 2020

수중 불분리성 그라우트는 수중 현장에 광범위하게 사용된다. 그러나 접합강도, 펌프 능력 및 강도 손실과 같은 주요 문제점이 여전히 존재한다. 본 연구에서는 자기충전, 비파괴 방지 그라우트 연구에 기초하여 이 분야의 현황을 파악하기 위해 수중 시공 및 카르스트 공동 실링에 관한 연구 동향에 대해 검토하였다. 그라우트를 수중에 사용할 경우, 공기 중에서 시공하는 것에 비해 강도와 접합강도가 손실될 것이다. 이를 방지하기 위해 고점도의 그라우트를 통해 카르스트 공동을 실링하고 있지만, 대심도에서는 그라우트의 펌핑 능력에 심각한 문제를 발생시키므로 기존의 수중 불분리성 그라우트와 콘크리트는 대심도 환경에 적합하지 않음을 의미한다.

• 소성∙가공
• /
• 제23권6호
• /
• pp.386-391
• /
• 2014

In the current study, Al-Mn-Zn alloys are strip-cast and used as the base alloy for the core of aluminum clad sheets used in automotive condenser fins. Transition elements such as Cu and Cr are added to the base core alloy in order to improve the properties of the clad sheets. The AA4343/Al-Mn-Zn-X(X: Cu, Cr)/AA4343 clad sheets are fabricated by roll bonding and further cold-rolled to a thickness of 0.08 mm. Clad sheets were intermediately annealed during cold rolling at $450^{\circ}C$ in order to obtain 40% reduction at the final thickness. Tensile strength and sag resistance of the clad sheets are improved by Cu additions to the core alloy, while corrosion resistance is also increased. Cr-additions to the clad sheets enhance sag resistance and provide low enough corrosion, although tensile strength is not improved. The effect of Cu and Cr additions on the properties of the clad sheets is elucidated by microstructural analysis.

• 한국염색가공학회지
• /
• 제28권1호
• /
• pp.33-39
• /
• 2016

The crystal structure of nylon 56 fibers post extended by drawing process was investigated by synchrotron x-ray scattering measurement. In as-cast fiber, distinct (004) and (020) diffraction peaks were observed and they were related to initial metastable alignment of nylon molecules. With increase in the drawing ratio, (110) peak intensity was increased in vertical direction with decreasing (020) peak. At the same time, (004)' peak evolved position tilted to 29 degrees from the (004) peak. This evolution is directly related to stable crystalline phase of nylon 56 originated from additional formation of hydrogen bondings between N-H and C=O by post drawing process. We also compared density variation, stress-strain curves of the fiber as a function of drawing ratio and strain. The variations of density and tanacity also supported the increase of stable structure of nylon 56.