• Journal of the Korean Geotechnical Society
• /
• v.33 no.8
• /
• pp.41-52
• /
• 2017

In this study, field measurements were investigated to analyze the load sharing ratio and behavior of piled raft foundation. The field measurements were performed for about 300 days from the start of construction. The geometry of the raft is $3.1m{\times}3.1m$, and the pre-cast and pre-bored pile is 23 m in length and 0.508 m in diameter. Based on the field measurements, the load-settlement relationship of the piled raft foundation was obtained, and the load sharing ratio of the pile was converged to 70% at ultimate loading condition. The load sharing ratio of the pile increased as the settlement increased, and this is because the surface friction of the weathered soil, which is at the lower ground, was significantly increased. Based on the results of the field measurements, load transfer curves were obtained and applied to a numerical analysis by using load transfer method.

• Biomedical Science Letters
• /
• v.3 no.2
• /
• pp.151-160
• /
• 1997

This study was planned to evaluate the urinary ascorbic acid as a new biological marker for the intoxication of cadmium, which could possibly be driven by its increased utilization and environmental pollution. In order to meet this goal, we have peformed measurement of urinary ascorbic acid concentration, histopathological examination of the kidney, and biochemical test for the liver function using cadmium-intoxicated rats by oral administration. The average concentrations of urinary ascorbic acid in the $CdCl_2$-treated rats were 214.0 mg/dl for 100 ppm group and 254.3 mg/dl for 200 ppm group during experimental period of 50 days. These levels are 24 and 28 times higher than one in the control group (9.0 mg/dl), respectively. Ultrastructural study showed the eosinophilic hyaline cast and focal effacement, fusion in the renal tubules, as well as loss of foot processes on the glomerular epithelial cells. These results suggested that cadmium may be responsible for renal glomerular injury. The blood levels of AST, ALT and LDH in the treated groups (199 IU/I, 88 IU/I, 1190 U/I for the 100 ppm group and 270 IU/I, 226 IU/I, 760 U/I for the 200 ppm group) were higher than ones in the control group(143 IU/I, 50 IU/I, 334 U/I). These results indicated the cadmium induced the damage of liver function. In conclusion, the administration of cadmium showed a remarkable increase of urinary ascorbic acid with renal and hepatic damage. Therefore, it is expected that measurement of urinary ascorbic acid would be an powerful method as a noninvasive biomarker for cadmium intoxication.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.206-211
• /
• 2020

Tungsten alloys are used widely in general industrial fields, but they are difficult to cast, so products are manufactured using powder metallurgy. In this study, a mixed powder of tungsten, nickel, and iron homogenized using a ball mill was added to pure water as a solvent, and PVA as a binder was added to prepare a spray drying mixture. The mixed liquid was prepared using a spraying machine. A study was carried out to produce a granular powder that can reduce the variations between products during the molding and sintering process of the powder metallurgy method. A preliminary experiment was conducted to confirm the influence of the variables in the granulation process. Through the preliminary test results, this experiment was performed with the volume of solvent of the spray drying the mixture as an independent variable, and granular powder having a mean particle size similar to that of the existing mass-production conditions and an increased apparent density was prepared. In addition, a pilot test was conducted for the molding and sintering process. The improved granular powder reduced the characteristic variation (weight variation) of the mass-produced product.

• Applied Chemistry for Engineering
• /
• v.18 no.5
• /
• pp.483-489
• /
• 2007

Polyaniline (PANI)/Polyimide (PI) membranes were prepared and the effects of PANI contents and doping on the structural properties and gas separation properties were studied. The polyamic acid (PAA) solution was prepared by the polycondensation reaction of 4,4'-(hexafluoroisopropylidene) diphthalic anhydride (6FDA) and 4,4'-oxydianiline (ODA) in 1-methyl-2-pyrrolydinone (NMP) solvent. The PANI/PI blends were obtained by mixing PAA solution and PANI solution, and were doped with 1 M aqueous HCl solution for 24 h. The structural characterizations of the as-cast and doped membranes were examined by FT-IR, XRD, and TGA. The gas permeation experiments with $H_2$, $CO_2$, $O_2$, $N_2$, and $CH_4$ were carried out by variable pressure method at $30^{\circ}C$ and 5 atm. For all gases tested, the permeability coefficients of the blends decreased with increasing PANI content and the magnitude of permeability was in the order of $H_2$ > $CO_2$ > $O_2$ > $N_2$ > $CH_4$. The permeability for PANI/PI membranes decreased after the doping process while the permselectivity increased. For $H_2/CH_4$ separation, the doped PANI/PI (75/25) membrane has a permselectivity of 991.

• Archives of Reconstructive Microsurgery
• /
• v.18 no.2
• /
• pp.55-61
• /
• 2009

Purpose: To analyze the clinical and radiologic results of the shoulder arthrodesis in brachial plexus injury patients with flail upper extremity. Material and Method: From Aug 1978 to April 2008, 29 shoulders in 29 patients with brachial plexus injury with shoulder fusion, we evaluated 20 shoulders in 20 patients, more than 1 year follow up. The average follow-up period was 6.45years (range: 1year~24years). There were 13 men and 7 women, and the mean age at the time of trauma was 32.0years(2~65 years). The type of injury was a motorcycle accident in 11 patients, in car accident in 5, pedestrian accident in 3, and fall from a height in 1. The lesion of injury was root and trunk in 1 patient, trunk and cord in 1, trunk in 18. Surgery was performed on the whole arm type paralysis in 12 patients, lower arm type paralysis in 8 patients. The preoperative visual analog scale score was 8.7(7~10). When the trapezius and serratus anterior muscle were in function, operation was performed. 18 patients were processed to the additional operation. Gracilis free flap in 6 patients, neurotization in 3, Steindler flexor plasty in 6, and tendon transfer in 3 were performed. Fixation was conducted with cancellous screws in 13 patients, Knoles pins in 5, and cancellous screws and Knoles pins in 2. The position of the arthrodesis at operation was $28.5^{\circ}$($20~45^{\circ}$) in abduction, $30.3^{\circ}$($20~45^{\circ}$) in flexion, and $30.8^{\circ}$($20~40^{\circ}$) in internal rotation. Result: The follow up visual analog scale score was 3.4(0~7). Postoperatively, shoulder spica cast was applied for 15.3weeks(8-20weeks). The median time to bony union was 17.7weeks(9~28weeks). Average range of motion was $32.0^{\circ}$($15~40^{\circ}$) of abduction, $24.0^{\circ}$($10~40^{\circ}$) of flexion, and $18.5^{\circ}$($10~30^{\circ}$)of internal rotation. Conclusion: The shoulder fusion in brachial plexus injury patients is one of the good methods to relieve pain, improve the function and stabilize the flail shoulder joint.

• Korean Journal of Ecology and Environment
• /
• v.39 no.2 s.116
• /
• pp.226-235
• /
• 2006

Populations of Zacco koreanus, distributed in four different tributaries of mid-upper reach Nakdong River were investigated to analyze a length-weight relation and von Bertalanffy's growth model. Fish sampling was conducted by common method (cast net and kick net) during March to October 2005. Fishes caught in the field were identified immediately, and then individuals of Zacco koreanus were preserved in 10% formalin to further measure their total length and weight in the laboratory. As the results of the equation based on length-weight relation, values of parameter b on the population of all tributaries were greater than 3.0 and the value on Bohyeon Stream was the maximum (3.26), indicating that the fish in the stream became more rotund as the length increases. In the mean time, we examined Brody growth constant (k) induced by the von Bertalanffy's growth model, and we found more steady state population in Wi (-0.18) and Byeongbo (-0.21) Streams than in fan (-0.38) and Bohyeon (-0.37) Streams. The findings would be used to assess local water environment on tributaries of the Nakdong River with understanding of ecological characteristics on the population of Zacco koreanus, as well as provide us fundamental information on domestic study of fish ecology.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.3
• /
• pp.20-27
• /
• 2014

In the construction site, various earth retaining systems are developed and applied to maintain stability of excavated area and structures. Among the methods, the underground continuous wall and the column-type diaphragm wall methods are especially used in construction site nearby buildings or roads. However, these methods have some disadvantages such as the difficulty of quality control and long curing time because these methods need to cast fresh concrete at the construction site. In addition, these methods are usually applied to the site for the temporary purpose. In this paper, we suggest precast hollow prestressed concrete pile for continuous pile wall system. To investigate the structural behavior of suggested pile, which is the main member of the suggested system, tests pertaining to the structural behavior and prestressing force applied in the pile are conducted. From the test results, it was found that the prestressing force measured is sufficient compared with the value obtained by the design equation and the cracking moment measured is 34% higher than the design value. In addition to the above, this precast hollow prestressed concrete pile has an additional safety margin that the maximum moment is 59.2% higher than the cracking moment which is one of the serviceability limits for the design of the system.

• The Journal of Korean Academy of Prosthodontics
• /
• v.43 no.1
• /
• pp.41-51
• /
• 2005

Statement of problem. Anatomic landmarks have been used in the orientation of occlusal plane and the determination of vertical dimension for edentulous patients. Such as labial vestibules of anterior region and hamular notches, retromolar pads of posterior region are very useful anatomic landmarks for fabrication of occlusion rim because they are to be identified on master casts. Therefore, if average distances between landmarks of maxillae and mandible in dentate subjects are measured and applied, not only occlusal plane but also vertical dimension can be established initially. Purpose. The purpose of this study is to measure vertical distances between anatomic landmarks and to present a guide to the orientation of occlusal plane and the determination of vertical dimension of edentulous patients. Material and method. Upper and lower border-molded casts were made in 93 Korean dentulous subjects, mean age 25 years. Incisal edges of central incisors, bottoms of labial vestibules, hamular notches and the half level of retromolar pads were marked on casts. Measurements of vertical distances from incisal edge of central incisor to the bottom of labial vestibule, between upper and lower bottoms of labial vestibules, from hamular notch to retromolar pad and from hamular notch to the occlusal plane established by the incisal edge of maxillary central incisor and mesiopalatal cusps of both maxillary first molars were made on each cast. Results and conclusion. 1. The mean distance from the incisal edge of central incisor to the bottom of labial vestibule was 20.8mm(SD 1.7) on upper casts and 17.3mm(SD 1.4) on lower casts. 2. The mean distance between both bottoms of labial vestibules of upper and lower casts was 35.0mm(SD 2.7). 3 The mean distance from hamular notch to the half level of retromolar pad was 5.0mm(SD 1.3). 4. The mean distance from hamular notch to occlusal plane was 7.9mm(SD 1.5). 5. Distances from incisal edge of central incisor to labial vestibule on lower casts(P<0.01) and from hamular notch to retromolar pad(P<0.0001) were greater in male than in female.

• The Journal of Korean Academy of Prosthodontics
• /
• v.42 no.1
• /
• pp.21-29
• /
• 2004

Statement of problem : Because dental impression can be a cross-infection source, disinfection, such as immersion disinfection is nessecary. However, the disinfection process may change the volume of the impression cast. Purpose : The purpose of this study is to find out the effects on dimensional change of different storage times and methods, of agar-alginate impression when immersed in a 5% idophor disinfectant. Material and Methods : An agar-alginate impression was made from a mandible model and then was disinfected and stored according the experimental conditions and a stone model was produced. Measurements were taken between reference points on the original mandible model and they were compared to measurements taken between reference points on the stone model. The study was divided into 4 groups. In group 1, the impression was stored in a 100% humidor for 30 minutes, 1 hour, 2 hours, 3 hours, 4 hours, 6 hours, 12 hours and 24 hours and stone models were made at each time. In group 2, the impression was immersed in 5% idophor disinfectant and then stored in a 100% humidor for the same length of times as group 1, and stone models were made at each time. In group 3, the impression was stored in extend-A-pourR, a special storage solution for 30 minutes, 1 hour, 2 hours, 3 hours, 4 hours, 6 hours, 12 hours, 24 hours 3 days, and 7 days and stone models were made at each time. In group 4, the impression was immersed in 5% idophor disinfectant and then stored in stored in extend-A-pourR, a special storage solution for the same length of times as group 3, and stone models were made at each time. 5 impressions and stone models were made at each time to make a total of 180. The Student-t test (P < .05) was used to do a statistical analysis of the measurements of the mandible model and stone models. The repeated-measure 2-way analysis of variance (P < .05) was used to do a statistical analysis of the difference in the 4 groups. Results : The percent liner dimensional change was from $0.25{\pm}0.03%$ (group 1, 30 minutes) to $0.34{\pm}0.06%$ (group 4, 7 days). No significant change was noticed between the 4 groups. Conclusion : According to the above study, in both methods, least dimensional change was recorded when the storage times were short and in both methods, immersion in 5% idophor disinfectant did not effect dimensional change in the agar-alginate impression.

• The Journal of Korean Academy of Prosthodontics
• /
• v.37 no.4
• /
• pp.474-493
• /
• 1999

According to repeated measurements and correction procedures, the accuracy of the phase-shifting profilometry was developed. At first, after 20 final models for maxillary complete denture were duplicated , the mucosa sur-faces of models were measured with the phase-shifting proflometry and each mirror view of these was calibrated. Maxillary casts were divided into 4 groups of 5 casts per each, and wax dentures with 2 sheets of baseplate wax and artificial teeth were made and then cured according to the curing method of each group. Group I ; quick curing with QC-20 acrylic resin Group II ; 9 hour curing with QC-20 acrylic resin Group III ; SR-Ivocap system Group IV ; metal base and quick curing with QC-20 acrylic resin. After curing, polishing, and storing at $37^{\circ}C$ in saline for 30 days, the forms of the impression surface of the dentures were measured with the phase-shifting profilometry. Then, the impression surface form of each denture was placed in the optimal position of com-parison with the mirror view of the same final cast. The amount and direction of distortion of each denture was analyzed and the effects of polishing and storage in each denture were compared, The obtained results were as follows : 1. In Group I, the denture was observed as the appearance distorted in the opposite direction of the mucosa and the postero-lateral part of palatal portion of the denture was observed as the appearance separated from the mucosa. Also, the buccal flanges of the denture were observed as the appearance distorted in the direction of the mucosa. 2. In Group II, the postero-lateral part of palatal portion of the denture was observed as the appearance separated slightly from the mucosa. The bilateral buccal flanges of denture were observed as the appearance distorted severely in the direction of the mucosa. 3. In Group III the bilateral part of the residual ridge crest portions and the buccal flanges of the denture were observed as the appearance distorted in the direction of the mucosa, and specially, the buccal flanges of the maxillary tuberosities were distorted severely. 4. In Group IV, the acrylic resin base of the buccal portion of the denture was observed as the appearance distorted in the opposite direction of the mucosa. 5. The phase-shifting profilometry, done with repeated measurements and correction procedures, was effective in comparing the amount and direction of distortion at every position after the laboratory work and the delivery of maxillary complete denture.