• Structural Engineering and Mechanics
• /
• v.82 no.1
• /
• pp.55-67
• /
• 2022

The precast reinforced concrete frame system is a method for industrialization of construction. However, the seismic performance factor of this structural system is not explicitly clarified in some existing building codes. In this paper, the seismic performance factor for the existing precast concrete building frame systems with cast-in-situ reinforced shear walls were evaluated. Nonlinear behavior of the precast beam-column joints and cast-in-situ reinforced shear walls were considered in the modeling of the structures. The ATC-19's coefficient method was used for calculating the seismic performance factor and the FEMA P-695's approach was adopted for evaluating the accuracy of the computed seismic performance factor. The results showed that the over-strength factor varies from 2 to 2.63 and the seismic performance factor (R factor) varies from 5.1 to 8.95 concerning the height of the structure. Also, it was proved that all of the examined buildings have adequate safety against the collapse at the MCE level of earthquake, so the validity of R factors was confirmed. The obtained incremental dynamic analysis (IDA) results indicated that the minimum adjusted collapse margin ratio (ACMR) of the precast buildings representing the seismic vulnerability of the structures approximately equaled to 2.7, and pass the requirements of FEMA P-695.

• Journal of Korean Society of Steel Construction
• /
• v.17 no.1 s.74
• /
• pp.93-102
• /
• 2005

Manufacturing conventional column base plate requires much manpower and time. In this research, a new method for constructing column base plate is introduced to improve on conventional methods through the use ofcast steel that is available for adjusting base plate thickness and enlarging base plate stiffness. The main purposes include reducing welding work, enlarging base plate stiffness, and clarifying the stress flow. Also, construction convenience and improvement in quality can be expected. For developing this cast steel base plate, test specimens of conventional and cast steel base plates are made and tested to analyze strength and stiffness. Also, the efficiency for long-term use is checked by fatigue tests. From these comparative tests, cast steel base plates have the same strength and stiffness as conventional base plates.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.4
• /
• pp.5-12
• /
• 2005

Recently, geophysical prospecting methods have played very important roles in civil and environmental engineering problems. Technical advances in geophysical instruments and computer system made it possible to get underground images with very high resolution far purposes to resolve those problems. It was possible partly due to ever increasing demand for development of technologies needed to precisely detect polluted areas and prevent ground-related accidents. Based on the same demand, integrity tests of cast-in place piles draw more attention and development of accurate test procedures is required. Ultrasonic methods is one of most advanced non-destructive procedures. In the paper, a geotomography method is employed for the cast-in place pile integrity test using ultrasonic waves. The image of pile interior is scanned and scrutinized far better and more accurate decision in the cast-in place pile integrity. In this study, we firstly examined the accuracy fur tomography program with idealized synthetic models built in water tank: their position and size were changed in the tank and each case was studied. In the next stage, real concrete pile models were fabricated and images of anomaly areas inside the pile were scanned to successfully locate those areas.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.5
• /
• pp.601-610
• /
• 2007

Statement of problem: The adhesion between titanium and ceramic is less optimal than conventional metal-ceramic bonding, due to reaction layer form on cast titanium surface during porcelain firing. Purpose: This study characterized the effect of titanium-ceramic adhesion after gold and TiN coating on cast and wrought titanium substrates. Material and method: Six groups of ASTM grade II commercially pure titanium and cast titanium specimens$(13mm{\times}13mm{\times}1mm)$ were prepared(n=8). The conventional Au-Pd-In alloy served as the control. All specimens were sandblasted with $110{\mu}m\;Al_2O_3$ particles and ultrasonically cleaned for 5min in deionized water and dried in air before porcelain firing. An ultra-low-fusing dental porcelain (Vita Titankeramik) was fused on titanium surfaces. Porcelain was debonded by a biaxial flexure test at a cross head speed of 0.25mm/min. The excellent titanium-ceramic adherence was exhibited by the presence of a dentin porcelain layer on the specimen surface after the biaxial flexure test. Area fraction of adherent porcelain (AFAP) was determined by SEM/EDS. Numerical results were statistically analyzed by one-way ANOVA and Student-Newman-Keuls test at ${\alpha}=0.05$. Results: The AFAP value of cast titanium was greatest in the group 2 with TiN coating, followed by group 1 with Au coating and the group 3 with $Al_2O_3$ sandblasting. Significant statistical difference was found between the group 1, 2 and the group 3 (p<.05). The AFAP value of wrought titanium was greatest in the group 5 with TiN coating, followed by the group 4 with Au coating and the group 6 with $Al_2O_3$ sandblasting. Conclusion: No significant difference was observed among the three groups (p>.05). The AFAP values of the cast titanium and the wrought titanium were similar. However the group treated with $Al_2O_3$ sandblasting showed significantly lower value (p<.05).

• Korean Journal of Agricultural Science
• /
• v.40 no.2
• /
• pp.147-153
• /
• 2013

The aim of study was to investigate genetic diversity for the calpain/calpastatin gene in three Hanwoo breeds [(Brown (n=62), Brindle (n=81) and Jeju Black (n=30)]. Random samples from three breeds of Hanwoo were selected and genotyped for the 7 SNPs of calpain/calpastatin using TaqMan method. Allele frequencies were investigated for CAPN1/CAST gene. Allele frequency of CAST2 SNP was 0.75, 0.59 and 0.22 for Brown, Brindle and Jeju black, respectively. The CAST3 revealed allele frequency of 0.59 and 0.57 in Brown and Jeju Black, while it showed very low allele frequency (0.07) in Brindle. In particular, favorable allele (G allele) for the CAPN1-2 SNP which was shown a strong association with tenderness in Taurine and Indicine cattle revealed 16% and 17% higher allele frequency in Brown Hanwoo (0.82) comparing Brindle (0.66) and Jeju Black Hanwoo (0.65). AMOVA demonstrated that among population variance occupied only 10% of total variance and among individual variance was 0%, while within individual variance was 90% of total variance. This result showed that population effect contributed very small portion of genetic to these three Hanwoo breeds, while within individual variance contributed large portion of genetic diversity within these Hanwoo breeds. In conclusion, three Hanwoo breeds (Brown, Brindle and Jeju black) showed a genetically homogeneous based on the 7 SNPs of CAPN1/CAST gene and it came from same ancestor to form modern Hanwoo breed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.8
• /
• pp.721-728
• /
• 2017

High-grade gray cast iron (HCI350) was prepared by adding Cr, Mo and Cu to the gray cast iron (GC300). Their microstructure, mechanical properties and fatigue strength were studied. Cast iron was made from round bar and plate-type castings, and was cut and polished to measure the percentage of each microstructure. The size of flake graphite decreased due to additives, while the structure of high density pearlite increased in volume percentage improving the tensile strength and fatigue strength. Based on the fatigue life data obtained from the fatigue test results, the probability - stress - life (P-S-N) curve was calculated using the 2-parameter Weibull distribution to which the maximum likelihood method was applied. The P-S-N curve showed that the fatigue strength of HCI350 was significantly improved and the dispersion of life data was lower than that of GC300. However, the fatigue life according to fatigue stress alleviation increased further. Data for reliability life design was presented by quantitatively showing the allowable stress value for the required life cycle number using the calculated P-S-N curve.

• Journal of Conservation Science
• /
• v.31 no.2
• /
• pp.95-104
• /
• 2015

Excavated archaeological cast iron objects in improper storage are quickly corroded and disintegrated into block and powder finally. Hence desalination treatment which is a way of removing internal corrosive factors, especially chloride ion, is an important process. But desalination is often omitted or objects are dehydrated by alcohol because the destruction of objects could occur during desalting. Although current desalting methods mostly use an aqueous alkali solution, $OH^-$ ions of water could accelerate corrosion and broaden internal cracks cause of high surface tension. Therefore this study experimented desalting using ethyl alcohol, which is low surface tension, to investigate an effect of desalination. As a result, desalting using ethyl alcohol showed the similar or more effective results of desalting using water. In addition, as aspects of desalting safety, ethyl alcohol desalting method was smaller destruction of objects and extraction of Fe from the objects than the aqueous alkali solution. However, this study explored the possibility of desalting methods using organic solvent in fieldwork, so the results would provide basic date for making the safe and effective desalting method for archaeological cast iron objects through further experiments.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.971-974
• /
• 2011

Aluminum matrix composites reinforced with SiC particles(AMC) are one of the candidate materials for the weight reduction of rolling stock brake discs. It is known that weight reduction of about 40% is possible when they replace conventional cast iron brake discs. But casting is not easy because of bad wettability of SiC with Al alloy. We developed two AMC brake discs with SiC volume fraction of 20% by a new casting method. It was found the developed method produced brake discs of good quality.

• Journal of Korean Institute of Industrial Engineers
• /
• v.20 no.3
• /
• pp.105-116
• /
• 1994

This paper presents an inventory model with partial backorders for the situation in which demand is deterministic, lead time follows normal distribution and back order ratio during the stockout period varies in proportion to the length of backorder period In this situations, an objective function is formulated to minimize a time-proportional backorder cast and a fixed penalty cost per unit lost. And then the procedure of iterative solution method for the model is developed to find optimal reorder paint and order quantity and a numerical example to illustrate the proposed method is presented.

• The Journal of Society for e-Business Studies
• /
• v.6 no.2
• /
• pp.167-178
• /
• 2001

Key is generally formed using the Random Number. How to make the Random Number is to cast coin or dice as classical method, to form the Real Random Number with Hardware and to make the Pseudo Random Number by means of utilizing mathematical algorithm. This thesis presented NRNG(New Random Number Generator) which put self-development Hardware to use as Key Generation Method and inspected to compare the Real Random Number with the Pseudo Random Number and special properties which PRNG(Pseudo-Random Number Generator) creates.