• Carbon letters
• /
• v.9 no.2
• /
• pp.115-120
• /
• 2008

Rubber reinforcing carbon black N330 was treated by physical activation under $CO_2$ to different degrees of burn-off. The mechanical properties indicating the reinforcement of SBR (Styrene-Butadiene Rubber) vulcanizates filled by activated carbon blacks, such as tensile strength, modulus at 300% strain and elongation at break were determined. During $CO_2$ activation of fresh carbon blacks, the development of microporous structure caused an increase of extremely large specific surface area and the porosity turned out to be an increasing function of the degree of burn-off. The tensile strength and modulus at 300% of activated carbon blacks filled rubber composites were improved at lower loading ratios of 20 and 30 phr, but decreased drastically after 30 phr, which is considered that it might be difficult to get a fully dispersed rubber mixture at higher loading ratios for fillers having very large specific surface areas. However, the Electromagnetic Interference (EMI) shielding effectiveness of SBR rubber composites having activated carbon black at 74% yield were improved at a large extent when compared to those having raw carbon black and increased significantly as a function of increasing loading ratio.

• Journal of the Korean Chemical Society
• /
• v.68 no.2
• /
• pp.87-92
• /
• 2024

The commercialization of rechargeable metal-air batteries is extremely desirable but designing stable oxygen reduction reaction (ORR) catalysts with non-noble metal still has faced challenges to replace platinum-based catalysts. The nonnoble metal catalysts for ORR were prepared to improve the catalytic performance and stability by the thermal decomposition of ZIF-8 with optimum cobalt loading. The porous carbon was obtained by the calcination of ZIF-8 and different loading amounts of Co nanoparticles were anchored onto porous carbon forming a Co/PC catalyst. Co/PC composite shows a significant increase in the ORR value of current and stability (500 h) due to the good electronic conductive PCN support and optimum cobalt metal loading. The significantly improved catalytic performance is ascribed to the chemical structure, synergistic effects, porous carbon networks, and rich active sites. This method develops a new pathway for a highly active and advantageous catalyst for electrochemical devices.

• Elastomers and Composites
• /
• v.33 no.5
• /
• pp.315-323
• /
• 1998

The purpose of this study was to investigate the crosslinking density and reinforcement of rubber compounds with various carbon black loadings, cure systems and cure temperatures. Bound rubber content increased with volume fraction of carbon black in rubber compounds, but total crosslinking density decreased with increasing the bound rubber content. Rate constant of cure reaction was changed significantly by cure system and cure temperature, especially it showed strong dependence on the cure temperature. High activation energys of cure reaction were shown in the rubber compound with high loading of carbon black under EC system and in the rubber compound with low loading of carbon black under CC system. High total crosslinking density of vulcanized compounds appeared in the rubber compound with low loading of carbon black and CC system among cure systems. Typical change of total crosslinking density by EC system was not shown. The highest elastic constant by Mooney-Rivlin equation was shown in the rubber compound with low loading of carbon black and SEC system. Modulus increased as increasing the loading of carbon black in the rubber compounds and showed the order of SEC, CC, and EC system for cure system.

• Carbon letters
• /
• v.5 no.1
• /
• pp.18-22
• /
• 2004

The failure behaviours of unidirectional pultruded carbon fiber reinforced polymer (CFRP) composites were monitored by the electrical resistance measurement during tensile loading, three-point-bending, interlaminar shear loading. The tensile failure behaviour of carbon fiber tows was also investigated by the electrical resistance measurement. Infrared thermography non-destructive evaluation was performed in real time during tensile test of CFRP composites to validate the change of microdamage in the materials. Experiment results demonstrated that the CFRP composites and carbon fiber tows were damaged by different damage mechinsms during tensile loading, for the CFRP composites, mainly being in the forms of matrix damage and the debonding between matrix and fibers, while for the carbon fiber tows, mainly being in the forms of fiber fracture. The correlation between the infrared thermographs and the change in the electrical resistance could be regarded as an evidence of the damage mechanisms of the CFRP composites. During three-point-bending loading, the main damage forms were the simultaneity fracture of matrix and fibers firstly, then matrix cracking and the debonding between matrix and fiber were carried out. This results can be shown in Fig. 9(a) and (b). During interlaminar shear loading, the change in the electrical resistance was related to the damage degree of interlaminar structure. Electrical resistance measurement was more sensitive to the damage behaviour of the CFRP composites than the stress/time curve.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.5
• /
• pp.121-129
• /
• 2006

This study look into the mechanisms of growth and magnification of the cracks and delamination in the pre-cracked RC beams repaired with carbon fiber sheets. The experimental parameters were loading type, loading speed and crack. In the experiments, it was confirmed that a failure of beams began with development and propagation of the stepped delamination in the below the loading point due to the rapid change of shear force, but mechanisms of the failure were not influenced with loading type, loading speed and pre-cracks. Particularly, in the case of beams having the pre-cracks, growth of crack concentrated at the special crack below the loading point and led to failure of the beam by delamination due to magnification of crack.

• Journal of Korean Society for Atmospheric Environment
• /
• v.26 no.4
• /
• pp.392-402
• /
• 2010

Black carbon (BC) concentrations were measured with an aethalometer (AE-16, 880 nm) at time interval of 5-min at an urban site of Gwangju over a year 2008. 24-hr filter-based integrated measurements of $PM_{2.5}$ particles were also made at the same site during the winter and summer intensive periods to test any optical loading bias in the raw BC data measured by aethalometer. BC concentration was higher in winter than in summer, possibly due to increase in emissions from energy consumption and poor dispersion with reduction of boundary layer in winter. Also temporal cycles of BC indicate that short-term transient spikes were common, occurring primarily during the rush-hour periods. A similar feature was also observed in diurnal concentration cycle of CO, mainly emitted from motor vehicles. When both low wind speed and weather patterns such as mist, haze and etc were combined, high BC concentrations frequently occurred. The amount of optical loading effect described by the "k" factor showed the seasonal variation, ranging from 0.0003 to 0.0036. This implies that optical loading effect is not seen at all times. From the comparison between the filter-based elemental carbon (EC) and aethalometer BC data, it was found that the loading compensated BC values were more reasonable than the raw BC ones reported from the aethalometer.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.377-382
• /
• 2001

Mechanical behavior and electrical resistance change of CPDP (carbon particle dispersed plastic) composite consisting of epoxy resin and conductive carbon particle were investigated under monotonic loading and repeated loading-unloading. The electrical resistance almost linearly increased with increasing strain during loading and the residual electrical resistance was observed even after removing load. The value of the residual electrical resistance was dependent on the maximum strain under the applied stress. This result suggests that the estimation of maximum strain (i.e., damage) is possible by the measuring electrical resistance of composite. The behavior of electrical resistance change during and after loading was discussed on the basis of the results of microscopic deformation and fracture observation. Moreover, the relationship between the volume fraction of carbon particle and the electrical resistivity of CPDP was investigated in relation to the percolation theory. Simulation model of percolation structure was established by Monte Carlo method and the simulation result was compared to the experimental results. The electrical resistance change under applied loading was analyzed quantitatively using the percolation equation and a simple model for the critical volume fraction of carbon particle as a function of the mechanical stress. It was revealed that the prediction was in good agreement with the experimental result except in the region near the failure of material.

• 대한공업교육학회지
• /
• v.32 no.2
• /
• pp.188-198
• /
• 2007

Platinum nanoparticles loading on carbon nanotube was carried out by impregnation of hexachloro platinate(IV) from hydrogen hexachloro platinate(IV) hydrate dissolved solution without using reduction agents, and heating the hexachloro platinate(IV) impregnated carbon nanotube up to $400^{\circ}C$. The amounts of impregnated hexachloro platinate(IV) on to carbon nanotube were measured with UV-visible spectrophotometer. The TG, XRD, and TEM analysis were performed to confirm the platinum particles loading and distribution on carbon nanotube. The average platinum particles size on carbon nanotube was under 2 nm by heating the hexachloro platinate(IV) up to $400^{\circ}C$ in spite of non-using reduction agents, while the average size increased due to the agglomeration of some particles by heating them up to $800^{\circ}C$. Therefore, uniformly distributed platinum nanoparticles loading on carbon nanotube can be obtained from simple impregnation of hexachloro platinate(IV) from solution and heating it up to $400^{\circ}C$.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.757-762
• /
• 2001

This study was performed experiment for strengthened bridge decks with isotropic carbon fiber sheets received fatigue loading, and compared with fatigue behavior of unstrengthened bridge decks. By the results, this study was examined effect of increasing strengthened to phase life cycles of bridge deck for fatigue loading and application of the punching shear theory of bridge deck strengthened by carbon fiber sheet.

• Macromolecular Research
• /
• v.9 no.3
• /
• pp.157-163
• /
• 2001

The influences of carbon black loading and cure type on the cure characteristics including kinetics and dynamic mechanical properties were investigated for a styrene-butadiene rubber (SBR). The rate constants of accelerated sulfur vulcanization reaction at three different temperatures were determined using a cure rheometer, and they were compared with those from the direct measurement of sulfur concentration. The strain softening behavior under dynamic deformation, known as the Payne effect was also discussed depending on the carbon black loading and cure type.