• KSBB Journal
• /
• v.17 no.2
• /
• pp.148-152
• /
• 2002

The extraction of volatile essential oil using supercritical carbon dioxide with 2%(v/v) ethanol and non-ethanol was performed in a semi-continuous flow extractor at the range of pressures and temperatures 6.9 to 17.2 MPa and 30 to 45$^{\circ}C$, respectively. When ethanol was added to the co-solvent, the solubility of volatile essential oils was increased up to 90% over the neat CO$_2$ value. The most efficiency of extraction of the voilatile essential oils was achieved at 13.8㎫ and 40$^{\circ}C$ by supercritical carbon dioxide with entrainer from Citrus junos peel.

• Resources Recycling
• /
• v.26 no.6
• /
• pp.38-44
• /
• 2017

As by-pass dust (BPD) made from cement manufactured process is designated waste, it is required to bury as high cost. The main component of BPD is potassium chloride (KCl), and used for the fertilizer. For using KCl to the fertilizer, the pH value of KCl is required as neutral or weak acid. However, it is not suitable to apply BPD into the fertilizer directly without any other treatment because BPD's pH value is shown 12.0~12.5; a high base. In this study, the carbon dioxide ($CO_2$) was used for removing calcium oxide (CaO) and reducing pH value during manufacturing process of KCl. We fixed inner condition of the carbon test chamber as $25^{\circ}C$-50RH%, and retained 0~7 hours under the 20 vol% of $CO_2$ atmosphere. After experiment, we analyzed the content of CaO and pH value from each samples. The more time exposed to $CO_2$, the content of CaO and pH value are shown. Furthermore, pH value exposed in 6 hours nearly reached 7.

• Asian Journal of Atmospheric Environment
• /
• v.10 no.2
• /
• pp.99-113
• /
• 2016

In order to improve the portability of basic absorbents monoethanolamine (MEA) and glycine (Gly), both were supported on microporous activated carbon (AC). Chemical modification by alkali-metal ion exchange (of Li, Na, K) was carried out on Gly-based absorbents. All supported absorbents were subjected to $CO_2$ absorption capacity (pure $CO_2$) and selectivity (indoor level) tests. Textural and chemical characterizations were carried out on test sorbents. All impregnation brought about significant reduction of specific surface area and microporosity of the adsorbent Depreciation in the textural properties was found to result to reduction in pure $CO_2$ sorption. Contrarily, low-level $CO_2$ removal capacity was enhanced as the absorbent dosage increases, resulting in supported 5 molar MEA in methanol solution. Adsorption capacities were improved from 0.016 and 0.8 in raw ACs to 1.065 mmol/g for MEA's. Surface chemistry via X-ray photoelectron spectroscopy (XPS) of the supported sorbents showed the presence of amine, pyrrole and quaternary-N. In reducing sequence of potency, pyridine, amine and pyrrolic-N were noticed to contribute significantly to $CO_2$ selective adsorption. Furthermore, the adsorption isotherm study confirms the presence of various SNGs heterogeneously distributed on AC. The adsorption mechanism of the present AC adsorbents favored Freundlich and Langmuir isotherm at lower and higher $CO_2$ concentrations respectively.

• Clean Technology
• /
• v.25 no.4
• /
• pp.275-282
• /
• 2019

In this study, the extraction of Conger myriaster oil by using supercritical carbon dioxide (SC-CO₂) and organic solvent was investigated. The extraction conditions conducted for SC-CO₂ varied for pressure (25, 30 MPa) and temperature (45, 55 ℃), while the SC-CO₂ flow rate was kept constant during the experiment (27 g min^-1) and hexane was used as a conventional organic solvent. The extraction yield indicated that the best extraction condition would be SC-CO₂ at 55 ℃ and 30 MPa, resulting in the highest yield of 37.73 ± 0.14%. The oils were characterized for their fatty acid (FAs) composition using gas chromatography, while it was revealed that the major FAs were mystric acid, palmitoleic acid, oleic acid, electroosapentaenoic acid (EPA), and docosahexaenoic acid (DHA). The oxidation stability of the extracted C. myriaster oil was evaluated by measuring the acid value, peroxide value, and free fatty acid. The best oxidative stability was obtained from SC-CO₂ extracted oil at 30 MPa and 55 ℃. There was a significant difference in the color properties of the SC-CO₂ and hexane extracted oils, with the SC-CO₂ extracted oil showing better chromaticity than the oil extracted using hexane. Extracting oils from C. myriaster with SC-CO₂ could bring better economic benefits than using organic solvents. When supercritical carbon dioxide was used, there was no post-treatment process; thus, it was confirmed that this is a more environmentally friendly oil extraction method.

• Journal of Environmental Science International
• /
• v.21 no.6
• /
• pp.705-711
• /
• 2012

Adsorption experiment of carbon dioxide was performed on MCM41 silica with a 30 wt.% EDA(ethylenediamine) loading at different $CO_2$ inlet concentration and various adsorption temperature. The surface characteristics of $CO_2$ capturing agent were carried out using BET analysis, X-ray diffraction and FT-IR. The results of BET showed 781 $m^2/g$ for MCM41 and 464 $m^2/g$ for EDA/MCM41. X-ray diffraction results reveled typical hexagonal pore system. The higher sorption capacity of EDA/MCM41 was about 80 $mg_{CO2}/g_{sorbent}$ with 50% $CO_2$ inlet concentration and 303 K adsorption temperature. The isosteric heat of adsorption in 303-353 K ranged from -25.47 to -28.24 KJ/mole for EDA/MCM41, which indicates $CO_2$-EDA/MCM41 interaction with exothermic adsorption process. Finally, the performance of EDA/MCM41 in 10 consecutive sorption-desorption runs was a stable with only a minor drop in its sorption capacity.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.184-187
• /
• 2007

Hydrogen could be produced from any substance containing hydrogen atoms, such as water, hydrocarbon (HC) fuels, acids or bases. Hydrocarbon fuels couold be converted to hydrogen-rich gas through reforming process for hydrogen production. Even though fuel cell have high efficiency with pure hydrogen from gas tank, it is more beneficial to generate hydrogen from city gas (mainly methane) in residential application such as domestic or office environments. Thus hydrogen is generated by reforming process using hydrocarbon. Unfortunately, the reforming process for hydrogen production is accompanied with unavoidable impurities. Impurities such as CO, $CO_2$, $H_2S$, $NH_3$, and $CH_4$ in hydrogen could cause negative effects on fuel cell performance. Those effects are kinetic losses due to poisoning of electrode catalysts, ohmic losses due to proton conductivity reduction including membrane and catalyst ionomer layers, and mass transport losses due to degrading catalyst layer structure and hydrophobic property. Hydrogen produced from reformer eventually contains around 73% of $H_2$, 20% or less of $CO_2$, 5.8% of less of $N_2$, or 2% less of $CH_4$, and 10ppm or less of CO. Most impurities are removed using pressure swing adsorption (PSA) process to get high purity hydrogen. However, high purity hydrogen production requires high operation cost of reforming process. The effect of carbon dioxide on fuel cell performance was investigated in this experiment. The performance of PEM fuel cell was investigated using current vs. potential experiment, long run (10 hr) test, and electrochemical impedance measurement when the concentrations of carbon dioxide were 10%, 20% and 30%. Also, the concentration of impurity supplied to the fuel cell was verified by gas chromatography (GC).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.2
• /
• pp.644-650
• /
• 2021

This study characterized the reforming of methane with carbon dioxide, which is a major cause of global warming. The methane decomposition reaction with carbon dioxide was carried out using transition metal catalysts. The reactivity of tin was lower than that of a transition metal, such as nickel and iron. Most of the decomposition reaction occurred in the solid state. The melting point of tin is 505.03 K. Tin reacts in a liquid phase at the reaction temperature and has the advantage of separating carbon produced by the decomposition of methane from the liquid tin catalyst. Therefore, deactivation due to the deposition of carbon in the liquid tin can be prevented. Methane decomposition with carbon dioxide produced carbon monoxide and hydrogen. Ni was used to promote the catalyst performance and enhance the activity of the catalyst and lifetime. In this study, catalysts were synthesized using the excess wet impregnation method. The effect of the reaction temperature, space velocity was measured to calculate the activity of catalysts, such as the activation energy and regeneration of catalysts. The carbon-deposited tin catalyst regeneration temperature was 1023 K. The reactivity was improved using a nickel co-catalyst and a water supply.

• Journal of the Korea Concrete Institute
• /
• v.15 no.3
• /
• pp.443-453
• /
• 2003

The diffusivity of carbon dioxide in concrete is very important in that it directly affects the degree of carbonation in concrete structures. The purpose of the present study is to explore the diffusivity of carbon dioxide and to derive a realistic equation to estimate the diffusion coefficient of carbon dioxide in concrete. For this purpose, several series of concrete specimens have been tested. Major test variables were the water-cement ratios. The total porosities and the diffusion coefficients of carbon dioxide were measured for the specimens. The present study indicates that the measured porosities agree well with the calculated ones. The effects of porosity and relative humidity on the diffusion coefficient of carbon dioxide were examined. A prediction equation to estimate the diffusion coefficient of carbon dioxide was derived and proposed in this study. The proposed equation shows reasonably good correlation with test data on the $CO_2$ diffusion coefficient of concrete

• Journal of Chest Surgery
• /
• v.25 no.12
• /
• pp.1399-1403
• /
• 1992

The evaluation of the effectivess of ongoing cardiopulmonary resucitation efforts is dependent on the commonly used methods, such as the presence of femoral or carotid artery pulsations, arterial blood gas determinations, peripheral arterial pressure and intracardiac pressure monitoring. But recent studies suggest that end-tidal carbon dioxide tension serves as a non-invasive measurement of pulmonary blood flow and therefore cardiac output under constant ventilation. A prospective clinical study was done to determine whether end-tidal carbon dioxide monitoring in open heart surgery under cardiopulmonary bypass could be used as a prognostic indicator of bypass weaning. We monitored end-tidal PCO2 values continuously during cardiopulmonary bypass in 30 patients. "Ohmeda 5210 CO-2 monitor" under infrared absorption method were incorperated into the ventilator circuit by means of a side point adaptor between endotracheal tube and ventilator tubing. 18 patients[Group I ] were res-ucitated from partial bypass followed by aorta cross clamp off and 12 patients[Group II ] from aorta cross clamp off followed by partial bypass. But there was no difference between two groups[p>0.05]. The value of end-tidal carbon dioxide tension during ventricular fibrillation or nearly arrest state was 6.6$\pm$2.9 mmHg, and at the time of spontaneous beating was 19.3$\pm$5.6 mmHg[Mean$\pm$Standard deviation], In conclusion end-tidal carbon dioxide tension monitoring provides clinically useful, continous, noninvasive and supplementary prognostic indicator during cardiopulmonary bypass weaning procedures.rocedures.

• Korea-Australia Rheology Journal
• /
• v.18 no.2
• /
• pp.83-90
• /
• 2006

Supercritical carbon dioxide ($scCO_2$) has advantages of being incorporated in polymer with high solubility and of being recovered easily by depressurizing. $scCO_2$ reduces the viscosity of polymer melt and it is expected to be use as a plasticizing agent. In this work, we studied on the effect of $scCO_2$ on the rheological properties of polymer melts during extrusion process. Slit die attached to twin screw extruder was used to measure the viscosity of polymer melts plasticized by supercritical $CO_2$. A gas injection system was devised to accurately meter the supercritical $CO_2$ into the extruder barrel. Measurements of pressure drop within the die, confirmed the presence of a one phase mixture and a fully developed flow during the measurements. The viscosity measurement of polypropylene was performed at experimental conditions of various temperatures, pressures and $CO_2$ concentrations. We observed that melt viscosity of polymer was dramatically reduced by $CO_2$ addition.