• Applied Chemistry for Engineering
• /
• v.23 no.4
• /
• pp.383-387
• /
• 2012

This paper presents an easy way to prepare carbon dioxide sorbent by using commercially available fumed silica particles (AEROSIL). AEROSIL was impregnated with various concentration of polyethyleneimine (PEI) in methanol and $CO_2$ capture ability was analyzed by thermo gravity analysis (TGA). The $CO_2$ adsorption capacity of 50 wt% PEI-impregnated AEROSIL was 126.2 mg/g-sorbent at $75^{\circ}C$ and this capacity was substantially higher than that of the mesoporous silica such as HMS (101.0 mg/g-sorbent) and MSU-J (66.1 mg/g-sorbent).

• Korea-Australia Rheology Journal
• /
• v.20 no.1
• /
• pp.1-6
• /
• 2008

Absorption rate of carbon dioxide was measured in the aqueous xanthan gum (XG) solution in the range of 0-0.15 wt% containing 2-amino-2-methyl-1-propanol (AMP) of $0-2\;kmol/m^3$ in a flat-stirred vessel with an impeller of 0.05m and agitation speed of 50rpm at $25^{\circ}C$ and 0.101 MPa. The volumetric liquid-side mass transfer coefficient ($k_La$) of $CO_2$, which was correlated with the viscosity and the elastic behavior of XG solution containing Deborah number as an empirical formula, was used to estimate the chemical absorption rate of $CO_2\;(R_A)$. $R_A$, which was estimated by mass transfer mechanism based on the film theory using the physicochemical properties and the kinetics of reaction between $CO_2$ and AMP, was compared with the measured rate. The aqueous XG solution with elastic property of non-Newtonian liquid made $R_A$ increased compared with Newtonian liquid based on the same viscosity of the solution.

• Nuclear Engineering and Technology
• /
• v.54 no.9
• /
• pp.3540-3550
• /
• 2022

The supercritical carbon dioxide (S-CO₂) Brayton cycle is an important energy conversion technology for the fourth generation of nuclear energy. Since the printed circuit heat exchanger (PCHE) used in the S-CO₂ Brayton cycle has narrow channels, Rayleigh-Bénard (RB) convection is likely to exist in the tiny channels. However, there are very few studies on RB convection in supercritical fluids. Current research on RB convection mainly focuses on conventional fluids such as water and air that meet the Boussinesq assumption. It is necessary to study non-Boussinesq fluids. PRB convection refers to RB convection that is affected by horizontal incoming flow. In this paper, the computational fluid dynamics simulation method is used to study the PRB convection phenomenon of non-Boussinesq fluid-supercritical carbon dioxide. The result shows that the inlet Reynolds number (Re) of the horizontal incoming flow significantly affects the PRB convection. When the inlet Re remains unchanged, with the increase of Rayleigh number (Ra), the steady-state convective pattern of the fluid layer is shown in order: horizontal flow, local traveling wave, traveling wave convection. If Ra remains unchanged, as the inlet Re increases, three convection patterns of traveling wave convection, local traveling wave, and horizontal flow will appear in sequence. To characterize the relationship between traveling wave convection and horizontal incoming flow, this paper proposes the relationship between critical Reynolds number and relative Rayleigh number (r).

• Journal of Korean Society of Water and Wastewater
• /
• v.30 no.4
• /
• pp.391-399
• /
• 2016

In this study, carbon dioxide ($CO_2$) was used as an inhibitor of scale production on the surface of RO membrane. In order to compare the effects of $CO_2$ injection on scale production, four RO modules: 1) without $CO_2$ injection and anti-scalant (RO module #1), 2) with only $CO_2$ injection (RO module #2), 3) with only anti-scalant (RO module #3), 4) with both $CO_2$ injection and anti-scalant (RO module #4), were operated for 60 days under constant flux mode. The trans-membrane pressure (TMP) was observed to decrease significantly in RO modules with $CO_2$ injection as compared with the other RO modules. When the feed water pH was controlled at 5.0 by injecting $CO_2$, the maximum TMP in RO modules #2 and #4 was founded to decrease by 42 and 40%, respectively. Moreover, the $Ca^{2+}$ concentration in the concentrate was 20mg/L lower in RO modules without $CO_2$ injection which is attributed to the scale formation on the surface of the RO membranes. The SEM-EDS analysis further showed a serious fouled RO membrane surface in RO modules #1 and #3.

• Journal of the Korean Ceramic Society
• /
• v.36 no.10
• /
• pp.1016-1021
• /
• 1999

In this study activated carbon fibers were prepared from PAN-based carbon fibers by physical activation with steam or carbon dioxide. The variations in specific surface area amount of iodine adsorption and pore size distribution of the activated carbon fibers after the activation process were discussed. in steam activation BET surface area of about 1019 m2/g was obtained after 77% burn-off while carbn dioxide activation produced ACF with 694m2/g of BET surface area after 52% burn-off. However carbon dioxide activation produced at a similar degree of activation higher micropore volume(0.37 cc/g) and amount of iodine adsorption (1589mg/g) than steam activation. Nitrogen adsorption isotherms for (PAN based activated carbon fibers that prepared by physical activation were of type I in the Brunauer-Deming-Deming-Teller classification

• Journal of Korean Society for Atmospheric Environment
• /
• v.33 no.1
• /
• pp.1-10
• /
• 2017

Adsorption is a plausible technology using solid adsorbents for dry capture of carbon dioxide ($CO_2$). In general, narrow size distribution of tiny pores and surface chemical functionalities of solid adsorbents enhance the adsorption capacity of gaseous $CO_2$ molecules. In order to utilize the advantages of fibrous adsorbents, this work prepared activated carbon nanofibers (ACNFs) via the electrospinning process using a polymer precursor of polyacylonitrile (PAN). The spun fibers were 390 nm to 580 nm in thickness with an average surface area of $27.3m^2/g$. The surface structure was improved by a programmed thermal activation at $800^{\circ}C$ in $CO_2$ atmosphere. It was also found that the nitrogen-groups including pyrrole and pyridine were created during the activation facilitaing the selective adsorption as forming enhanced active sites. The finally obtained adsorption capacities were 2.74 mmol/g for pure $CO_2$ flow and 0.74mmol/g for 3000 ppm.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.8 no.2
• /
• pp.71-76
• /
• 2000

The biological carbon dioxide fixation using microalgae has been known as an effective carbon dioxide reduction technology. With many environmental factors influencing microalgal productivity, the desirable cultivation factors were investigated using a green alga, Euglena gracilis. It has the high protein and vitamin E to be used as fodder. In batch culture with a photobioreactor, initial pH, temperature, carbon dioxide concentration and light intensity in the optimum cultivation condition were 3.5, $27^{\circ}C$,5-10% and $520{\mu}mol/m^2/s$, respectively. After that, the optimum hydraulic retention time (HRT for the continuous cultivation was 4 days at carbon dioxide concentration of 10%. In this condition, the final dry cell weight was 1.2g/l.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.1065-1066
• /
• 2011

• Korean Journal of Ecology and Environment
• /
• v.34 no.4 s.96
• /
• pp.261-266
• /
• 2001

Effects of elevated carbon dioxide ($CO_2$) on soil microbial processes were studied in a northern peatland. Intact peat cores with surface vegetation were collected from a northern Welsh fen, and incubated either under elevated carbon dioxide (700 ppm) or ambient carbon dioxide (350 ppm) conditions for 4 months. Higher algal biomass was found under the elevated $CO_2$ condition, suggesting $CO_2$ fertilization effect on primary production, At the end of the incubation, trace gas production and consumption were analyzed using chemical inhibitors. For methane ($CH_4$ ), methyl fluoride ($CH_3F$) was applied to determine methane oxidation rates, while acetylene ($C_2H_2$) blocking method were applied to determine nitrification and denitrification rates. First, we have adopted those methods to optimize the reaction conditions for the wetland samples. Secondly, the methods were applied to the samples incubated under two levels of $CO_2$. The results exhibited that elevated carbon dioxide increased both methane production (210 vs. $100\;ng\;CH_4 g^{-1}\;hr^{-1}$) and oxidation (128 vs. $15\;ng\;CH_4 g^{-1}\;hr^{-1}$), resulting in no net increase in methane flux. For nitrous oxide ($N_2O$) , elevated carbon dioxide enhanced nitrous oxide emission probably from activation of nitrification process rather than denitrification rates. All of these changes seemed to be substantially influenced by higher oxygen diffusion from enhanced algal productivity under elevated $CO_2$.

• KSBB Journal
• /
• v.13 no.1
• /
• pp.101-107
• /
• 1998

Carbon dioxide is estimated to be responsible for 60% of the global warming effect, and this percentage is tending upward. Studies on removal and fixation of $CO_2$ in the flue gas are recognized as one of the important roles of the future biotechnology. Photobiological systems have considerably higher photosynthetic efficiency than conventional biomass system. The experiment for the photosynthetic fixation of $CO_2$ and the biomass production was performed with various initial cell concentration in a tubular photobioreactor and a bubble column $CO_2$ contactor with a gas sparger of $CO_2$ -enriched air(0.03~20%). Synechocystis PCC 6803 could grow at 10~20% $CO_2$ content under pH control. The highest specific growth rate, 0.0258 $h^{-1}$ , was obtained at 5% $CO_2$-air mixture. The maximum cell production rate, 0.2784 g/L.day, was obtained when the initial cell concentration was 0.45 g/L at 5% $CO_2$ -air mixture. The maximum cell concentration was 2.03 g/L in the tubular photobioreactor when the light intensity was $45.5{\mu}$ $E/m^2$ . s. This system showed 0.482 g $CO_2$ /L . day of the $CO_2$ fixation.