• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 가을 학술발표회 논문집
• /
• pp.185-192
• /
• 1999

This paper presents the results of a parametric study on the behavior of tunnel face reinforced with horizontal pipes. A three-dimensional finite element model was adopted in this study to capture the three-dimensional nature of tunnel face behavior under various boundary conditions. A parametric study was peformed on a wide range of boundary conditions with emphasis on the effect of reinforcing layouts on the deformation behavior of tunnel face. The results of analysis such as tunnel face deformation behavior under various conditions were thoroughly analyzed, and a database for the behavior of tunnel face under different reinforcing conditions was established for future development of a semi-empirical design/analysis method for the tunnel face reinforcing technique. The results indicated that there exits an optimum reinforcing layout for a given tunnel condition, which must be selected with due consideration of tunnel geometry and ground condition.

• 상하수도학회지
• /
• 제10권1호
• /
• pp.78-84
• /
• 1996

The presence of ammonia, usually in the form of ammonium ion ($NH_4{^+}$), can enhance bacterial growth m the distribution system and make the production of drinking water more costly if ammonium must be removed to ensure good disinfection. Removal of ammonia by biological oxidation could be economical which prevents excess chlorine dosage In this research, effects of hydraulic retention time (HRT) and media type on the ammonia removal efficiencies of submerged biofilm reactor were investigated. The biofilm reactors combined the characteristics of high biological solids capture efficiency and good hydraulic control. The results indicate that biofilms can remove over 77 percent of the ammonia with HRT of longer than 2 hr even at low temperature ranging from 14.6 to $16.6^{\circ}C$. The HRT has a significant effect on nitrification. The overall nitrification and efficiency of ammonia removal increase with increasing HRT. It has also been observed that when the fibrous media was used, the ammonia removal, nitrification rate and endurance to shock improved.

• 한국환경과학회지
• /
• 제20권10호
• /
• pp.1233-1241
• /
• 2011

The main objective of this experimental investigation was $CH_4$ recovery from biogas generated in municipal and wastewater treatment plant. The polysulfone hollow fiber membrane was prepared in order to investigate the permeation properties of $CH_4$ and $CO_2$. Permeability of $CO_2$ in Polysulfone membrane was 11-fold higher than of $CH_4$ gas. A membrane pilot plant for upgrading biogas was constructed and operated at a municipal wastewater treatment plant. The raw biogas contained 66 ~ 68 Vol % $CH_4$, the balance being mainly $CO_2$. The effect of the operating pressure of feed and permeate side and feed flowrate on $CH_4$ recovery concentration and efficiency were investigated with double stage membrane pilot plant. The $CH_4$ concentration in the retentate stream was raised in these tests to 93 Vol % $CH_4$.

• Toxicological Research
• /
• 제17권
• /
• pp.197-199
• /
• 2001

Enhancement of antigen-specific IgE is a hallmark of allergic hyperresponsiveness, therefore it is necessary to adopt or develop a highly sensitive and specific assay for determination of allergen-specific IgE levels in vivo. In this presentation, we introduce an ELISA (enzyme linked immunosorbent assay) system developed to measure the levels of chicken egg ovalbumin (OVA)-specific IgE in serum. The ELISA method uses a commercially available purified rat anti-mouse IgE as a capture Ab and biotinylated OVA as a detection reagent. Avidin-peroxidase with its substrate is used for color development resulting in optical density measurement at 405 nm. The ELISA system produces a highly sensitive dose-response relation-ship between optical density levels and the dilution titer of the OVA-IgE standard serum but no cross-reaction with unrelated IgE or IgG. It is believed that the system is an Efficient tool to delineate an adjuvant effect of environmental pollutants on development of asthmatic and atopic responses.

• Steel and Composite Structures
• /
• 제36권2호
• /
• pp.179-186
• /
• 2020

In this paper, the forced resonance vibration of porous functionally graded (FG) curved nanobeam is examined. In order to capture the hardening and softening mechanisms of nanostructure, the nonlocal strain gradient theory is employed to build the size-dependent model. Using the Timoshenko beam theory together with the Hamilton principle, the equations of motion for the curved nanobeam are derived. Then, Navier series are used in order to obtain the dynamical deflections of the porous FG curved nanobeam with simply-supported ends. It is found that the resonance position of the nanobeam is very sensitive to the nonlocal and strain gradient parameters, material variation, porosity coefficient, as well as geometrical conditions. The results indicate that the resonance position is postponed by increasing the strain gradient parameter, while the nonlocal parameter has the opposite effect on the results. Furthermore, increasing the opening angle or length-to-thickness ratio will result in resonance position moves to lower-load frequency.

• Smart Structures and Systems
• /
• 제21권1호
• /
• pp.113-122
• /
• 2018

In this article, an exact analytical solution for mechanical buckling analysis of magnetoelectroelastic plate resting on pasternak foundation is investigated based on the third-order shear deformation plate theory. The in-plane electric and magnetic fields can be ignored for plates. According to Maxwell equation and magnetoelectric boundary condition, the variation of electric and magnetic potentials along the thickness direction of the plate is determined. The von Karman model is exploited to capture the effect of nonlinearity. Navier's approach has been used to solve the governing equations for all edges simply supported boundary conditions. Numerical results reveal the effects of (i) lateral load, (ii) electric load, (iii) magnetic load and (iv) higher order shear deformation theory on the critical buckling load have been investigated. These results must be the analysis of intelligent structures constructed from magnetoelectroelastic materials.

• Korea-Australia Rheology Journal
• /
• 제21권1호
• /
• pp.71-79
• /
• 2009

The incomplete saturation and the void formation during the resin infiltration into fibrous porous media in the resin transfer molding process cause failure in the final product during its service. In order to better understand flow behavior during the filling process, a finite-element scheme for transient flow simulation across the micro-structured fibrous media is developed in the present work. A volume-of- fluid (VOF) method has been incorporated in the Eulerian frame to capture the evolution of flow front and the vertical periodic boundary condition has been combined to avoid unwanted wall effect. In the microscale simulation, we investigated the transient filling process in various fiber structures and discussed the mechanism leading to the flow fingering in the case of random fiber distribution. Effects of the filling pressure, the shear-thinning behavior of fluid and the volume fraction on the flow front have been investigated for both intra-tow and the inter-tow flows in dual-scale fiber tow models.

• Transactions on Electrical and Electronic Materials
• /
• 제11권3호
• /
• pp.106-111
• /
• 2010

The convergence of significantly different and disparate technologies such as spintronics, carbon nano tube field effect transistors, photon and bio-responsive molecular switches, memristor and memristive systems and metamaterials, coupled with energy scavenging sources are gaining a renewed focus in the quest for new products. This paper will provide an insight into an anticipated technological revolution and will highlight a futuristic Roadmap to capture opportunities that are brought about as the results of formulation of new circuit components basically driven by emergence of nanoscale materials as part of System on System integration. Challenges as the result of new lumped components such as memristor, metamaterial-based lumped components and the like that will challenge the designers' comfort zone will also be discussed.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2010년 춘계학술대회논문집
• /
• pp.103-108
• /
• 2010

This article presents computational fluid dynamics (CFD) simulations of nanoparticle movements and flow characteristics in laboratory-scale electrostatic precipitator (ESP) without corona discharge, and for simulation, it uses the commercial CFD program(CFD-ACE) including electrostatic theory and Lagrangian-based equation for nanoparticle movement. For validation of CFD results, a simple cylindrical type of ESP is simulated and numerical prediction shows fairly good agreement with the analytical solution. In particular, the present study investigates the effect of particle diameter, inlet flow rate, and applied electric potential on particle collection efficiency and compares the numerical prediction with the experimental data, showing good agreement. It is found that the particle collection efficiency decreases with increasing inlet flow rate because the particle detention time becomes shorter, whereas it decreases with the increase in nanoparticle diameter and with the decrease of applied electric voltage resulting from smaller terminal electrostatic velocity.

• Computers and Concrete
• /
• 제1권4호
• /
• pp.433-455
• /
• 2004

The paper presents results of FE-calculations on shear localizations in quasi-brittle materials during both an uniaxial plane strain compression and uniaxial plane strain extension. An elasto-plastic model with a linear Drucker-Prager type criterion using isotropic hardening and softening and non-associated flow rule was used. A non-local extension was applied in a softening regime to capture realistically shear localization and to obtain a well-posed boundary value problem. A characteristic length was incorporated via a weighting function. Attention was focused on the effect of mesh size, mesh alignment, non-local parameter and imperfections on the thickness and inclination of shear localization. Different methods to calculate plastic strain rates were carefully discussed.