• Journal of the Korean Geotechnical Society
• /
• v.19 no.6
• /
• pp.307-323
• /
• 2003

In this study the pilot test of C.G.S (Compaction Grouting System) as injection method by low slump mortar was performed and the results were analyzed in order to find out the application of this method to the soft ground and the effect of settlement restraint. The site for pilot test is adjacent to apartments supported by pile foundations. Sand drain method was performed previously as countermeasures against settlement, but settlement occurs continuously because this ground is very soft. Site investigations such as SPT, CPT and vane shear test were performed to determine the characteristics of ground improvement after the installation of C.G.S. Field measurements were performed on purpose to find out the displacement of ground during the installation of C.G.S. From the results of this study, C.G.S method can be optimized by the control of radius, space, depth, injection material and injection pressure. C.G.S improves soft ground with radial consolidation of adjacent soft ground. Considering that increase of N value to about 3, C.G.S can be considered as an effective method to increase the bearing capacity as well as constrain the settlement of soft ground. It is also expected to be economic and effective in the improvement of ground when it is used in applicable sites.

• Journal of the Korean GEO-environmental Society
• /
• v.1 no.1
• /
• pp.27-33
• /
• 2000

Stone columns is ground improvement method which is composed of compacted gravel or crushed stone inserted into the soft ground consisting of loose sand and clay by replacement method. Generally stone columns are constructed in silty clay, above 70% replacement rate for increasing the bearing capacity and shear strength. Low replacement stone columns method is limited below 30% at replacement rate-premising strength increase of clay ground is estimated efficiently. This study, laboratory model tests were conducted to investigate the consolidation drainage promotion and shear strength increase effect in soft ground with replacement rate by stone columns. The settlement reduction effect and settlement reduction coefficients increase with increasing the replacement rate in composite ground. The results of model tests indicate that consolidation promotion effect is proved. The increasing strength of composite ground was verified by vane shear tests.

• Journal of the Korean housing association
• /
• v.16 no.1
• /
• pp.27-35
• /
• 2005

It has seen the significant increase of water consumption rate due to rapid industrialization, high-densities of city, and increasing the population; thereby leads further water resource required in near future. In order to solve this deficit there are one of solution that gray water method demonstrates advantages regarding the questions of optimal water utility and thereby master plan of water. The method of study is analysis of investigation data through interview and research of sewage treatment plants in Daegu City. Through these analysis, this paper examines the capacity of graywater and optimal graywater facility.

• IE interfaces
• /
• v.24 no.4
• /
• pp.274-280
• /
• 2011

Delayed access to surgery may lead to deterioration in the patient condition, poor clinical outcomes, increase in the probability of emergency admission, or even death. The purpose of this work is to decide the number of patients selected from a waiting list and to schedule them in accordance with the operating room capacity in the next period. We formulate the problem as an infinite horizon Markov Decision Process (MDP), which attempts to strike a balance between the patient waiting times and overtime works. Structural properties of the proposed model are investigated to facilitate the solution procedure. The proposed procedure modifies the conventional value iteration method along with the binary search technique. An example of the optimal policy is provided, and computational results are given to show that the proposed procedure improves computational efficiency.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.9
• /
• pp.1192-1198
• /
• 2014

With an increase in the penetration of offshore wind farm, the need of an accurate economic evaluation of offshore wind farm has become crucial. This paper presents an economic evaluation method of offshore wind farm in Korea reflecting the cost of offshore wind farm infrastructure (offshore substation, submarine cable and foundation) in its cost model. Each cost of offshore substation, submarine cable, and foundation is represented as a function of installed capacity, distance to shore, and water level, respectively. We have applied the method to the case study of offshore in Jeju Island and analyzed the economics under various conditions. The results show that the distance to shore is of importance in economics of offshore wind farm.

• Proceedings of the KIEE Conference
• /
• 2006.10c
• /
• pp.360-362
• /
• 2006

This paper proposes a new track-following control method using disturbance observer with the freedom of gain and frequency adaptation in optical disk drive system. Recent ODDs use smaller track pits, higher rotation speed and broader rotational speed variations to increase the data capacity and data transfer rate. This cause the degradation of track-following performance by increasing the disturbance of the rotary system. In this paper, we discussed on a DOB structure that efficiently attenuate the disturbance without effecting the overall feedback loop characteristics on CLV type ODD which uses a higher and broader range of rotational speed. DOB structure uses two band pass filter. We analyzed the track-following performance sensitivity on rotational frequency variance and gain changes. This analysis is done on a computer simulation environment and actual ODD product.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.74-77
• /
• 1998

We consider connection-oriented wireless cellular networks. These networks employ dedicated radio channels for the transmission of signaling information. A forward signaling channel is a common signaling channel assigned to carry the multiplexed stream of paging and channel allocation(virtual circuit allocation) packets from a base station to mobile stations. The delay levels experienced by paging and channel allocation packets have serious effect on the utilization level of the limited radio channel capacity. While a slotted mode operation is used to reduce the power consumption level at mobile stations, it may induce an increase in packet delay levels. In this paper, we thus consider a multiplexing scheme for paging and channel allocation packets under which slots are dynamically allocated for the paging packet transmission. For this dynamic scheme, we develop an analytical method for deriving the delay characteristics exhibited by paging and channel allocation packets, and investigate the effect of network parameters on the delay level by using this method.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2001.11a
• /
• pp.124-129
• /
• 2001

With the social demands for tall building, the level of techniques for construction become high and there are various building materials. Also, the construction system become very complicated with the increase of worker. In spite of above facts, the method of construction management depends on the experimental capacity of a construction manager, and there are many unreasonable elements. These elements prevent well-going in construction process. To solve this problem, it is necessary to make a new system of construction management which is adequate for the condition of company and the contents of construction. In this study, the characteristic of production system and the present condition of construction management were investigated with the help of survey. Thus, the new method of construction management which can clear the previous problems was proposed.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.10a
• /
• pp.176-179
• /
• 1998

In general, machining time by electrical discharge machining (EDM) process is much longer than that of cutting process, so rough-cut has done for the purpose of reducing machining time prior to EDM Nowadays EDM speed is improving due to the advance of EDM capacity. Therefore a new method, machining a raw material directly by EDM without rough-cut, is used widely. EDM area is varies according to the EDM position in three-dimensional EDM process, so EDM parameters should be determined adaptively based on the EDM area to increase productivity. However it is difficult to calculate EDM area corresponding to the EDM position the EDM workers who have experience in shop floor determine machining parameters by experience. This paper proposes a method for determining EDM parameters based on EDM area corresponding to EDM position.

• Tribology and Lubricants
• /
• v.22 no.1
• /
• pp.26-32
• /
• 2006

This work analyzes the behaviors of aerated lubricant in the gap between con-rod bearing and journal. Aerated lubricant influences two major factors on the film formation. One is the density characteristics of the lubricant due to the volume change by the bubbles and the other is the viscosity characteristics of the lubricant due to the surface tension of the bubble. Those two major factors surprisingly increase the load capacity in certain ranges of bubble sizes and densities. Modified Reynolds' equation is developed with the consideration of aerated ratio in the lubricant and journal locus is computed with the Mobility method after the computation of two dimensional pressure distributions over the bearing area.