• Journal of the Korean Society for Marine Environment & Energy
• /
• v.8 no.3
• /
• pp.111-115
• /
• 2005

The concentration of atmosphere carbon dioxide ($CO_2$) which is one of the major greenhouse gas, continues to rise by the increase in fossil fuel consumption, forest destruction and decrease of biological diversity, etc. In order to weaken the global warming, a reduction of $CO_2$ discharge to the atmosphere is required. The $CO_2$ ocean sequestration technology utilizes the intrinsic oceanic capacity of $CO_2$ absorption, diluting and/or dispersing the liquefied $CO_2$ in the deep ocean (>2,000 m). This geo-engineering approach is regarded as one of the occasions to mitigate the $CO_2$ concentration in the atmosphere. Some developed centuries such as Japan, USA, Norway, etc. have intensively carried out the projects on the research and development of $CO_2$ ocean sequestration since 1990s. There have been several approaches to develop the relative technological system to mitigate the increasing $CO_2$, however, there was no systematic and practical R&D programme in the $CO_2$ ocean sequestration. This paper has described the state of the art on the three optional methods of $CO_2$ sequestration, and compared with them in the aspect of the applicable possibility.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.12
• /
• pp.2175-2185
• /
• 2000

Respiration rate should be a reasonable state variable for the activated sludge and could be used to simulate the performance of the activated sludge process. Toxic materials are classified into three groups, competitive, noncompetitive and uncompetitive. They increase/decrease the half saturation coefficient or specific growth rate. that means decreasing of the substrate removal capacity. In this research, a pilot-scale activated sludge process was operated under extended aeration method, and a representative noncompetitive inhibitor, acidic wastewater was applied to establish a respirometry-based toxicity model. Using this model. the correlation coefficient between measured and calculated respiration rate was 0.96 when acidic wastewater(pH 3.9~5.5) was introduced continuously to the aeration tank. Even though respiration rate was decreased by toxic effect of acidic wastewater, effluent substrate concentration represented to COD was deteriorated just a little bit. It might be caused by the low ratio of readily biodegradable substrate in the input substrate. Reduction of respiration rate by decreasing of input substrate concentration was much lower than that by acidic wastewater, and hence it was estimated that the possibility of false toxic alarm caused by decreasing of substrate concentration should be low.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.339-344
• /
• 2016

Since transmissions of large amounts of data are frequent, users require more bandwidth, and the need for communications networks having greater bandwidth is increasing. One communications network satisfying this need is an optical communications network. Therefore, studies to increase the transmission capacity of optical communications systems have been carried out. However, in a general optical communications system, a signal transmitted through optical fiber (a transmission medium) is detected through direct detection in the receiving system. This method has a disadvantage in that the entire bandwidth of the optical signal cannot be utilized. Also, when transmitting an optical signal, there is a problem where the signal-to-noise ratio is affected by neighboring channels. To overcome this situation, various studies are being conducted to minimize the influence of external interference and noise. This paper overcomes the situation by transmitting spectrum-sliced signals using the digital transmission system, FSK. Analyzing the characteristics of the signals detected in the receiver of the optical communications system, Gaussian distribution is used for the PDF of the spectrum-sliced signal, and the signal at the receiving end of the optical communications system is assumed to have a k-square distribution. The results of the analysis confirmed it is better to transmit the spectrally divided signal rather than transmit the laser source.

• The Korean Journal of Emergency Medical Services
• /
• v.10 no.3
• /
• pp.5-20
• /
• 2006

Purpose: This study examines the degree of empowerment recognized by the 1st paramedics and the trend of their critical thinking, analyzes correlations between empowerment and critical thinking to reveal whether there is statistically significant difference between them and then is to provide basic materials necessary for research on empowerment and critical thinking. Method: This study distributes 105 structured self-report questionnaires to the 1st emergency medical technicians working at fire fighting police boxes, general hospitals, clinics and emergency medical information centers in G Metropolitan City and J province from April 29 to May 28, 2006, collects their responses directly and analyzes results with t-test, F-test(ANOVA) and Pearson's Correlation Coefficient. Result: 1. First, average score of empowerment of subjects was 4.68 out of 6 and according to scores by area, capacity 5.98 was highest, followed by significance 5.41, self- determination 4.44 and effectiveness 3.79. 2. degree of empowerment according to general characteristics of subjects showed statistically significant differences in final education(F=2.714, p= .049), level of salary (F=3.298, p= .014) and satisfaction of current job (F=5.399, p= .001). 3. average score of critical thinking of subjects was 3.28 out of 7 and according to areas, no bias 3.95 was highest, followed by maturity 3.68, structure 3.35, inquisitiveness 3.11, pursuit of truth 3.07, critical thinking and self-confidence 3.00, analyticity 2.98. 4. degree of critical thinking by general characteristics of subjects showed statistically significant differences in age(F=2.577, p= .041), final education (F=7.877, p= .000), current workplace (F=3.513, p= .018), level of salary(F=4.628, p= .002), satisfaction with current job(F=6.879, p= .000) and intention to transfer current job(t=15.21, p=.000). 5. as a result of correlations between empowerment and critical thinking of subjects, Pearson correlation coefficients between whole empowerment and critical thinking were r= .21, p=.013. Conclusion: It is considered that the 1st paramedic managers must seek how to keep and manage empowerment and development of education and training program which can enhance critical thinking is needed. Further, emergency educators must develop educational program based on the concept of empowerment to establish early awareness of a desirable organization culture and increase understanding of empowerment in the process of education.

• Applied Chemistry for Engineering
• /
• v.24 no.4
• /
• pp.428-432
• /
• 2013

From the forest areas in Chungbuk, large amounts of wood wastes by pruning are generated, however most of them considered as by-products are not treated properly with no disposal options. In this work, among diverse wood wastes such as Quercus variabillis, Juniperus chinensis, Larix kaemoferi, and Pinus densiflora, Juniperus chinensis was found to be more effective biosorbent for the removal of lead ions than other wood wastes. Also, the enhancement of lead removal efficiency from the aqueous phase was investigated using Juniperus chinensis waste. It was observed that the optimal initial pH to increase the removal efficiency of 20 mg/L lead ions was 4.0 and the optimal dosage concentration with regard to the biosorbent for the enhanced removal of 50 mg/L lead ions was 0.6 g/100 mL. In addition, chemical treatment of Juniperus chinensis waste with sulfuric acid was required to improve the adsorption capacity for high lead concentrations (over 100 mg/L). When Juniperus chinensis waste was chemically treated with 6 M sulfuric acid, the adsorption quantities of lead ions were 180, 340, and 425 mg/g with regard to 200, 400, and 500 mg/L lead ions concentrations, respectively. These results indicate that the practical biosorbent technology developed in this study is a highly efficient method to treat the lead ion from an aqueous solution.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.2
• /
• pp.83-90
• /
• 2009

White LEDs(Light Emitting Diode) offer advantageous properties such as high brightness, improved reliability, lower power consumption, and long lifetimes. An LED is an electronic device that converts an electrical signal into a tight signal and is used not only in Optical Communication Indoor wireless optical illuminating rooms, but also for wireless optical communication systems. Currently, studies about these white LEDs have been being progressed, and in this raper, we discuss the multiplex and the multiple access method of VLC(Visible Light Communication) systems using white LEDs. In proposed system, CDMA(Code Division Multiple Access) apples to VLC system to reduce interference of VLC system, and improve capacity. The superiority of OOK modulation is presented in analysis of results by comparing VLC-CDMA communication system using OOK(On-off keying) modulation and BPSK modulation in AWGN(Additive White Gaussian Noise) channel and Diffuse channel. And we investigate the significance of a solution of interference by multipath by comparing BER in multipath channel and AWGN channel. In the proposed system, we assume Directed LOS(Line Of Sight) and Diffuse Link, and suppose VLC-CDMA using OOC(Optical Orthogonal Code) as methods to increase efficiency of system by removing ISI(Inter Symbol Interference) caused by multiple access, optical spreading code, and also present an analysis of its performance.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.6
• /
• pp.623-641
• /
• 2020

About 5 km length of tunnels were constructed by mechanized tunnelling method using closed type shield TBM. In order to avoid construction delay problems for ensuring timely electricity transmission, it is necessary to increase the prediction accuracy of the excavation process involving machines according to rock mass types. This is important to corroborate the project duration and optimum operation for various considerations involved in the machine. So, full-scale tunnelling tests were performed for developing the advance rate model to be appropriately used for 3.6 m diameter shield TBM. About 100 test cases were established and performed using various operational parameters such as thrust force and rotational speed of cuttterhead in representative uniaxial compressive strengths. Accordingly, relationships between normal force and penetration depth and, between UCS and torque were suggested which consider UCS and thrust force conditions according to weathered, soft, hard rocks. Capacity analysis of cutterhead was performed and optimum operational conditions were also suggested based on the developed model. Based on this study, it can be expected that the project construction duration can be reduced and users can benefit from the provision of earlier service.

• Asian-Australasian Journal of Animal Sciences
• /
• v.14 no.9
• /
• pp.1233-1237
• /
• 2001

A study was conducted to determine the effects of maturity at harvest and wilting days on the quality of round baled rye (Secale cereale L.) silage. This study was a $3{\times}3$ factorial arrangement in a split plot design with 3 replicates. The main plot was 3 harvesting dates at the stage of boot (20 Apr.), heading (29 Apr.) and flowering (14 May). The subplot was wilting day : 0 (unwilted), 0.5 and 1 day (0, 1, and 2 days at boot stage). Acid detergent fiber (ADF) and neutral detergent fiber (NDF) contents of rye silage were significantly greater than those of rye before ensiling, but crude protein (CP) content and in vitro dry matter digestibility (IVDMD) were vice versa. Buffering capacity (BC) of rye harvested at flowering stage was decreased from 264 to 202 meq/kg at 1 day wilting, however, it was increased when harvested at boot or heading stage. The pH in wilted silage was the highest while that of flowering stage was the lowest. Water soluble carbohydrate (WSC) content of wilting rye was lower than that of unwilted, and the lowest at late harvesting stage. All plots had minimal WSC content for silage fermentation. Wilting treatment and delayed harvesting date caused an increase in dry matter (DM) content of round bale silage. The content of ammonia-N expressed as a portion of total N showed negative correlation with DM content. High quality silage according to ammonia-N content could be obtained from mid-harvest with wilting. There were highly significant differences in each organic acid between harvesting dates and wilting periods. Acetic and butyric acid contents were increased with delayed harvesting and prolonged wilting period, the lactic acid content, however, was decreased. This study demonstrated that harvest of rye from heading to flowering stage with wilting would be a recommendable method for making high quality rye silage using round bale system.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.5
• /
• pp.439-446
• /
• 2018

The PHC pile has been increasingly used due to its implementation of the top-base method, which is advantageous in high penetration rate and bearing capacity reinforcement. Typically, when a PHC pile is manufactured, high-strength mixed materials are mainly used to enhance the compressive strength. However, recent studies have been conducted to utilize ground granulated blast-furnace slag (GGBS) in terms of economic efficiency. For this reason, this study manufactured PHC pile considering the replacement ratio and curing conditions of GGBS instead of high-strength mixed materials, and further investigated the engineering properties of the PHC pile. According to the experimental results, the compressive strength of GGBS-replaced PHC pile increased by steam curing, and particularly, PHC pile with 20% replacement of GGBS under $80^{\circ}C$ steam curing condition showed a compressive strength of approximately 84MPa. Furthermore, the experimental results confirmed that more hydration products were generated under the $80^{\circ}C$ steam curing condition than that under the $20^{\circ}C$ steam curing condition, which would affect the higher density of the PHC pile as well as the increase in the compressive strength.

• Restorative Dentistry and Endodontics
• /
• v.19 no.2
• /
• pp.473-484
• /
• 1994

To investigate the effect of resin cement, which had been known to increase the adhesive capacity of the cast gold inlay, on the gingival marginal fit and whether the tin-planting of the beveled area affects the marginal fit, Class II cast gold inlays were made on the 25 sound molars. Control group(ZPC goup) was cemented with the ZPC by conventional method. Experimental groups were cemented with the resin cement(Super-hond & $Panavia_{EX}$) and subdivided further by the existence or nonexistence of the tin-plating of the beveled area(ST & PT groups: with plating, SNT & PNT groups: without plating). So, each group was consisted of 5 teeth and the gingival margin of each specimen was mesiodistally sectioned by 3 times and the marginal and internal gap were evaluated by the Stereo Microscope (${\times}180$) and the Scanning Electron Micrascope(${\times}5,000$) was used for examining the adhesive relationship of the resin cement to the cavity wall and to the cast gold surface. The results were as follows : 1. Marginal gap was less than internal gap in all groups. 2. ZPC and SNT(bevel without tin-plating) groups showed the least gap and gap in PNT(bevel without tin-plating) group, ST(bevel with tin-plating) group, PT(bevel with tin-plating) group showed the greater value in order in evaluation of the both internal gap and marginal gap. 3. With the exception of the relationships between ZPC and SNT groups, ST and PNT groups, relationships between any other groups showed the statistical significance in the internal gap(p<0.05). 4. In the marginal gap, all relationships between groups showed the statistical significance (p<0.05) except the relationships between ZPC and SNT groups, ST and PNT groups, ZPC and PNT groups. 5. ZPC group showed more soluble phenamena than the resin groups(ST, SNT, PT, PNT). 6. Resin cement showed the void spaces in spite of good penetration into the micro-irregularities on both the tooth surface and the cast surface. The void was shown more in PT and PNT groups than in the ST and SNT groups. 7. After the treatment of heat and desiccation for SEM specimen, resin cements were detached more easily from the tooth surface than from the cast surface.