• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.9
• /
• pp.1227-1232
• /
• 2014

The purpose of this paper is to establish the optimum fabricating condition of specimens using silk screen printing, and to develop humidity sensor which has good humidity sensing properties. The specimens are fabricated under the condition of 90[wt%] $SnO_2$-10[wt%] $TiO_2$, and their microstructure, crystalline structure, humidity sensing properties are examined. From the microstructure analyses, porosity is best at 700[$^{\circ}C$]. From the crystalline structure analyses, intensity of peak becomes strong according to increasing heat treatment temperature. From the humidity sensing properties analyses, an overall results of capacitance changes, linearity and hysteresis for the specimens is best at 600[$^{\circ}C$] and 700[$^{\circ}C$]. Capacitance of specimens increases according to decreasing measurement frequency, and to increasing relative humidity.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.4
• /
• pp.29-37
• /
• 1999

This paper involves the "on-line" measurement of burrs using a capacitance sensor. A non-contact capacitance gauging sensor is attached to an ultra precision milling machine which was used as a positioning system The setup is used to measure burr profiles along machined workpiece edges. Experimental procedures and results as well as the basic theoretical principles of the capacitance sensor and specifications of related equipment are presented. The proposed scheme is shown to be accurate easy to setup and with minor modifications readily applicable to automatic deburring processes.processes.

• Journal of Sensor Science and Technology
• /
• v.20 no.4
• /
• pp.243-248
• /
• 2011

The purpose of this study is to develop a sensing system to measure the capacitance of a pre-developed engine oil deterioration detection sensor integrated with an oil filter. To measure the capacitance of engine oil in the sensor, it is used the way measuring the electric charging time in a capacitor by impressing DC volt. This method has merits on cost and signal stability. The measured capacitance is compensated by comparison with the one measured by an impedance analyzer. Also, using the dielectric constant gained by an impedance analyzer, the calculating equation of the dielectric constant of engine oil related with the currently developed sensor is decided. Finally, the degradation degree of engine oil is estimated according to the change rate of dielectric constant between green oil and used oil. The newly developed personal controller is to control a series of the processes.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.560-564
• /
• 1999

Burr sensing for burr size measurement and deburring process control is one of the essential elements in an automated deburring procedure. This paper presents the implementation of capacitance sensing and acoustic emission (AE) to deburring. The first application is the "on-line" measurement of burrs using a capacitance sensor. A non-contact capacitance gauging sensor is attached to an ultra precision milling machine which was used as a positioning system. The setup is used to measure burr profiles along machined workpiece edges. The proposed scheme is shown to be accurate, easy to setup, and with minor modifications, readily applicable to automatic deburring processes. As the second example, AE signals were sampled and analyzed for the sensor feedback of a precision deburring process - laser deburring -. The results, such as the sensitivity of AE signals to burr shapes and edge detection capability show a clear correlation between physical process parameters and the AE signals. A subsequent control strategy for deburring automation is also briefly discussed.

• Journal of Sensor Science and Technology
• /
• v.30 no.2
• /
• pp.88-93
• /
• 2021

In this paper, a folding sensor based on capacitance is proposed. The sensor was developed to sense the length and angle data for the milli-scale actuators without causing any interference to the actuating joints. For the sensing and testing the robotic joint with reducing the cost and complexity aspects of manufacturing, a simple composition was adopted. The sensor comprises a pair of copper tapes, papers, and wires. The complete sensing unit is constructed by bonding the tapes with the papers and soldering the wire to the copper parts. For accuracy, a teensy 4.0 board, which has a 12-bit ADC resolution, is employed. Furthermore, the sensed analog data is not translated into the unit of capacitance for accuracy; however, it is filtered using a low-pass filter and subsequently, a Butter-worth filter. The data obtained demonstrate a periodic waveform, which implies that the data are in good agreement with the hypothesis set prior to the experiments. Compared to other milli-scale sensors, this could be a better option for sensing the length and angle data for milliscale actuators.

• Korean Journal of Materials Research
• /
• v.13 no.3
• /
• pp.155-159
• /
• 2003

The polypyrrole and polyaniline thin film sensors which were made by chemical polymerization were employed to detect ethanol gas. With a single sensor element we can obtain characteristic patterns of behaviour across a very wide frequency range when measuring either resistance or capacitance. Impedance spectroscopy was employed to study the gas sensing behavior of both capacitance and resistance based sensors with conducting polymer as the active sensing element.

• Journal of electromagnetic engineering and science
• /
• v.17 no.1
• /
• pp.34-38
• /
• 2017

In this paper, we propose an active tunable bandpass filter (BPF) for efficient spectrum sensing in the TV White Space (TVWS) band. By designing a narrow bandwidth, it is possible to improve the sensing probability. The basic circuit configuration involves switching the PIN diode compromising capacitor bank to change the capacitance of the LC resonant circuit. To cover the whole TVWS band effectively, we add a varactor diode, and the bandwidth is set to 25-MHz. We improve the insertion loss by using the active capacitance circuit. The tunable BPF in the TVWS band with a 20-MHz interval is designed to have 11 channels with a bandwidth of 25 MHz and a low insertion loss of 1.7-2.0 dB.

• Journal of Sensor Science and Technology
• /
• v.8 no.1
• /
• pp.32-37
• /
• 1999

A capacitance-type humidity sensor with mesa structure in which porous silicon layer is used as humidity-sensing material is developed and its humidity sensing properties are measured. This sensor has a structure where two electrodes are set on the up-side of the wafer against the past typical structure having these electrodes on the up and down-side of the wafer. Therefore, the sensor can be fabricated monolithically to be more compatible with the IC process technology, and is possible to detect more correct output capacitance by removing the effect of the parasitic capacitance from the bottom layer and other junctions. To do this, the sensor was fabricated using process such as localized formation of porous silicon, oxidation of porous silicon layer, and etching of oxidized porous silicon layer. From the completed samples, the dependence of capacitance on the relative humidity of 55 to 90% more was measured at room temperature. As the result, the measured capacitance increased monotonously higher at the low frequency of 120 Hz, where the capacitance was observed to increase over 300%.

• Journal of Powder Materials
• /
• v.30 no.4
• /
• pp.310-317
• /
• 2023

Small-film-type ion sensors are garnering considerable interest in the fields of wearable healthcare and home-based monitoring systems. The performance of these sensors primarily relies on electrode capacitance, often employing nanocomposite materials composed of nano- and sub-micrometer particles. Traditional techniques for enhancing capacitance involve the creation of nanoparticles on film electrodes, which require cost-intensive and complex chemical synthesis processes, followed by additional coating optimization. In this study, we introduce a simple one-step electrochemical method for fabricating gold nanoparticles on a carbon nanotube (Au NP-CNT) electrode surface through cyclic voltammetry deposition. Furthermore, we assess the improvement in capacitance by distinguishing between the electrical double-layer capacitance and diffusion-controlled capacitance, thereby clarifying the principles underpinning the material design. The Au NP-CNT electrode maintains its stability and sensitivity for up to 50 d, signifying its potential for advanced ion sensing. Additionally, integration with a mobile wireless data system highlights the versatility of the sensor for health applications.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.2
• /
• pp.123-128
• /
• 2020

A low phase noise phase locked loop (PLL) with negative feedback loop including frequency variation sensing circuit (FVSC) has been proposed. The FVSC senses the frequency variation of voltage controlled oscillator output signal and controls the volume of electric charge in loop filter capacitance. As the output frequency of the phase locked loop increases, the FVSC reduces the loop filter capacitor charge. This causes the loop filter output voltage to decrease, resulting in a phase locked loop output frequency decrease. The added negative feedback loop improves the phase noise characteristics of the proposed phase locked loop. The size of capacitance used in FVSC is much smaller than that of loop filter capacitance resulting in no effect in the size of the proposed PLL. The proposed low phase noise PLL with FVSC is designed with a supply voltage of 1.8V in a 0.18㎛ CMOS process. Simulation results show the jitter of 273fs and the locking time of 1.5㎲.