• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.29 no.6
• /
• pp.900-908
• /
• 1996

Changes of paralytic shellfish toxin components and specific toxicity in blue mussel, Mytilus edu/is and oyster, Crassostrea gigas during canning process were investigated by high performance liquid chromatography (HPLC). The $mole\%$ of the frozen shucked blue mussel were in order of $27.5\;mole\%$ of gonyautoxin 1, $23.0\;mole\%$ of gonyautoxin 8 (C1) and $23.0\;mole\%$ of epi-gonyautoxin 8 (C2), while those of the frozen shucked oyster were in order of $29\;mole\%$ of C1, $22\;mole\%$ of C2, $16.7\;mole\%$ of gonyautoxin 2. Both samples had minor amounts of saxitoxin and neosaxitoxin. On the other hand, in case of specific toxicity, the major toxins were consisted of gonyautoxin $1\~4$ in both sample. The toxicity of gonyautoxin $1\~4$ were 88 and $84\%$ in blue mussel and oyster, respectively. According to the experimental results, C1, C2 and gonyautoxin 4 were very sensitive to heat treatment, while gonyautoxin 2 and saxitoxin were pretty heat resistant than any other toxin components.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.33 no.5
• /
• pp.399-402
• /
• 2000

Very little information is known on the canning of fishery products by vacuum pack. In this paper, some fundamental process conditions for the canning of fishery products were investigated. Moisture-controlled mackerel pike, shrimp and oyster were packed in lacquered cans with spice and additives. After sealing, pressure of the cans were reduced by do-aeration through specially designed gas-tight silicone rubber plug previously attacked to the lid. On this investigation, vacuum can prior to thermal processing were set up to 15, 30, 45 and 60 cmHg, The higher vacuum in cans showed the more quick heat transfer in thermal processing. tinder 60 cmHg vacuum, the heat transfer was more quick than that of the conventional water packed products, Under 15 cmHg, however, the heat transfer was markedly increased by air which acted as an insulator in conductive heat transfer. These results demonstrated that high vacuum was essential secure for the heat processing in vacuum pack.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.3
• /
• pp.419-427
• /
• 2013

The catalytic converters for automobile exhaust systems are manufactured by inserting a mat-wrapped substrate into a stainless steel can. A residual pressure that is too high will initiate a fracture in the substrate. In contrast, a residual pressure that is too low will fail to hold the substrate in the acceleration or deceleration phase. Both the process capability and mat pressure on the substrate are predicted while considering the effect of the statistical variation in the dimensions of the parts. The validity of the solutions is then confirmed. A program using EXCEL combines a finite element analysis and process capability analysis in one program.

• Korean Journal of Materials Research
• /
• v.11 no.7
• /
• pp.590-598
• /
• 2001

SiCp/pure Al and SiCp/2024Al MMCs were fabricated by in-situ VHP process designed specially just in this study which is composed of the vacuum hot press at range from R.T. to $500^{\circ}C$ and the continuous extrusion without canning process at $520^{\circ}C$. It was investigated the effect of SiC particle size, volume fraction and extrusion ratio on the tensile properties and micro structure in auf composites. In case of the 10:1 extrusion ratio, but SiCp/pure Al and SiCp/2024Al composites were shown a sound appearance and a good micro structure without crack of SiCp as well as uniform distribution of SiCp. However, in case of the 16:1 extrusion ratio, the number of cracked SiC particles more than increased in a higher volume fraction composite and 2024Al matrix composite compared with pure Al matrix one. The tensile strength of the composites reinforced smaller SiCp was higher than that of the bigger SiCp reinforced in same volume fraction and extrusion ratio.

• Journal of the Korean Ceramic Society
• /
• v.51 no.5
• /
• pp.453-458
• /
• 2014

SiC and its composites have been considered for use as nuclear fuel cladding materials of pressurized light water reactors. In this study, a $SiC_f$/SiC composite as a constituent layer of SiC triplex fuel cladding was fabricated using a chemical vapor infiltration (CVI) process in which tubular SiC fiber preforms were prepared using a filament winding method. To enhance the matrix density of the composite layer, winding patterns, deposition temperature, and gas input ratio were controlled. Fiber arrangement and porosity were the main parameters influencing densification behaviors. Final density of the composites decreased as the SiC fiber volume fraction increased. The CVI process was optimized to densify the tubular preforms with high fiber volume fraction at a high $H_2$/MTS ratio of 20 at $1000^{\circ}C$; in this process, surface canning of the composites was effectively retarded.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.1
• /
• pp.73-82
• /
• 1997

High temperature densification behaviors of alumina powder compacts were investigated under hot pressing and hot isostatic pressing. An alumina part of valve-head shape was fabricated under hot pressing and its forming process was simulated by finite element calculation. an alumina powder compact encapsulated by a stainless steel container was also densified under hot isostatic pressing. Inhomogeneous deformations during hot isostatic pressing due to the canning effect were observed experimentally and predicted by finite element analysis.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.192-193
• /
• 2006

The wet coating process could easily be made from large area film with printing paste mixed with semiconductor and binder material at room temperature. Semiconductor film fabricated about 25mm thickness was evaluated by field emissions-canning electron microscopy (FE-SEM). X-ray performance data such as dark current, sensitivity and signal to noise ratio (SNR) were evaluated. The $Hgl_2$ semiconductor was shown in much lower dark current than the others, but the best sensitivity. In this paper, reactivity and combination character of semiconductor and binder material that affect electrical and X-ray detection properties would prove out though experimental results.

• Transactions of Materials Processing
• /
• v.32 no.3
• /
• pp.114-121
• /
• 2023

During rolling, rolling mill rolls endure wear when shaping metal billets into a desired form, such as bars, plates, and shapes. Such wear affects the lifespan of the rolls and product quality. Therefore, in addition to rigidity, wear performance is a key factor influencing the performance of rolling mill rolls. Conventional methods such as casting and forging have been used to manufacture rolling mill rolls. However, powder alloying methods are increasingly being adopted to enhance wear resistance. These powder manufacturing methods include atomization, canning to shape the powder, hot isostatic pressing to combine the powder alloy with conventional metals, and various wear performance tests on rolls prepared with powder alloys. In this study, numerical simulations and experimental tests were used to develop and elucidate the wear analysis mechanism of rolling mill rolls. The wear characteristics of the rolls under various rolling conditions were analyzed. In addition, experimental tests (wear and surface analysis tests) and wear theory (Archard wear model) were used to evaluate wear. These tests were performed on two different materials in various powder states to evaluate the different aspects of wear resistance. In particular, this study identifies the factors influencing the wear behavior of rolling mill rolls and proposes an analytical approach based on the actual production of products. The developed wear analysis mechanism can serve the future development of rolls with high wear resistance using new materials. Moreover, it can be applied in the mechanical and wear performance testing of new products.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.47 no.1
• /
• pp.12-17
• /
• 2014

The cooling of precooked skipjack Katsuwonus pelamis is a critical thermal process in tuna canning because it affects the quality and yield of the canned tuna, as well as productivity. The combined method of vacuum cooling followed by water spraying (VC-WS) was investigated to increase cooling rates, and prevent loss of yield of the precooked tuna during vacuum cooling. For VC-WS, the precooked skipjack was cooled to $30^{\circ}C$ by vacuum at 31 mmHg and then wetted by spraying water for 2 min. The effects of VC-WS on cooling times, cooling loss, color, texture and lipid oxidation of the precooked tuna were compared with conventional spray cooling (SC).The cooling times for precooked skipjack from $75^{\circ}C-30^{\circ}C$ were 11 min for VC-WS and 145 min for SC. The cooling losses were 1.7 % for VC-WS and 1.6 % for SC. Peroxide and thiobarbituric acid (TBA) values of VC-WS were lower than those of SC. The loin of the VC-WS-treated skipjack was brighter and harder than the SC loin, as indicated by higher lightness and hardness values. Based on these results, we believe that the VC-WS process could compensate for the cooling loss of vacuum cooling and minimize changes in quality that occur during cooling of precooked skipjack tuna.

• Korean Journal of Food Science and Technology
• /
• v.13 no.4
• /
• pp.328-333
• /
• 1981

As a step to investigate energy conservation in canneries, energy consumption pattern and energy usages of various unit operations in a mushroom cannery were examined. The results are as follows; 1. In the mushroom cannery, fuel oil and electricity were used mainly for temperature control of mushroom growing house in winter and various cultivation operation respectively. To grow and process 1 kg of mushroom, thermal energy of 4634 kcal and electrical energy of 0. 116 kwh were consumed. About 80% of all energy was consumed for cultivation. 2. Steam qualities at each respective processing line were $92{\sim}94%$, giving no great differences among lines. 3. As a direct energy in 1 day processing operations of 8 tons of mushroom, thermal energy of $301.5{\times}10^{4}kcal$ and electrical energy of 60.1 kwh were used. The energy intensive operations were blanching (35%) and retorting (38%).