• Journal of Advanced Marine Engineering and Technology
• /
• v.4 no.1
• /
• pp.2-22
• /
• 1980

In the earlier days, when the diesel engine was used for ship propulsion, its shaft had often been broken by uncertain causes. Bauer suggested, for the first time in 1900, that it resulted from the torsional vibration of the shaft system. From 1901 to 1902, Gumbel and Frahm found out that shaft failures were caused by the resonance of the shaft system in critical speed. Since that time, valuable theories, empirical formulae and methods of vibration analysis were introduced by many investigators such as Geiger, Holzer, Lewis, Carter, Porter, Constant, Timoshenko, Dorey, Den Hartog, Tuplin, Ker Wilson, Bradbury etc. But, as the calculation of the damping energy involves very complicated and uncertain factors, the estimated amplitude of the torsional vibration is incorrect and uncertain. Besides, as high-powered engines have been installed on large vessels or special vessels and exciting force has been increased, new problems of the torsional vibration have continuously occurred. Although we can calculate the approximate natural frequencies or estimate their amplitude and additional stress in the design stage, through the above mentioned studies, the results of the calculations are unsatisfactory, and so much time is needed to carry out the calculation by hand. The authors have developed a computer program to calculate its natural frequencies, the amplitudes and additional stresses of the torsional vibration in the marine diesel engine shafting. In developing the computer program, the authors have paid the special attention to the calculation of the damping energy. To verify the reliability of the developed computer program, the torsional vibration of several propulsion shaftings which are driven by the diesel engine has been analyzed. The results calculted by the authors' computer program show good agreements with those of the actual measurements and are better than the results of engine maker's calculation.

• Proceedings of the KIEE Conference
• /
• 1998.07c
• /
• pp.918-922
• /
• 1998

With the development of industry, the qualitical advancement of power is needed. Since it is placed in the end step of power system, the fault at the distribution system causes some users blackout directly. So if the fault occurs, quick restoration is very important subject and, for the reason, induction of the distribution automation system is now being progressed briskly. For the quick restoration of the faulted distribution system, the load shedding of the blackout-area must be followed, and the other problems like the shedded load, faulted voltage and the rest may cause other accident. Accordingly load shedding must be based on the precise calculation technique during the distribution system load flow(dist flow) calculation. In these days because of its superior convergence characteristic the Newton-Raphson method is most widely used. The number of buses in the distribution system amounts to thousands, and if the fault occurs at the distribution system, the speed for the dist flow calculation is to be improved to apply to the On-Line system. However, Newton-Raphson method takes much time relatively because it must calculate the Jacobian matrix and inverse matrix at every iteration, and in the case of huge load, the equation is hard to converge. In this thesis. matrix equation is used to make algebraical expression and then to solve load flow equation and to modify above defects. Then the complex matrix is divided into real part and imaginary part to keep sparcity. As a result time needed for calculation diminished. Application of mentioned algorithm to 302 bus, 700 bus, 1004 bus system led to almost identical result got by Newton-Raphson method and showed constant convergence characteristic. The effect of time reduction showed 88.2%, 86.4%, 85.1% at each case of 302 bus, 700 bus system 86.4%, and 1004 bus system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.10
• /
• pp.2052-2058
• /
• 2009

As the operating frequency of digital system increases and voltage swing decreases, an accurate and high speed analysis of PCB board becomes very important. Transmission matrix method, which use the multiple products of unit column matrix, is the highest speedy method in PCB board analysis. In this paper a new method to reduce the calculation time of PCB board impedances is proposed. First, in this method the eigenvalue and eigenvectors of the transmission matrix for unit column of PCB are calculated and the transmission matrix for the unit column is transformed using similarity transform to reduce the number of multiplication on the matrix elements. This method using the similarity transform can reduce the calculation time greatly comparing the previous method. The proposed method is applied to the 1.3 inch by 1.9 inch board and shows about 10 times reduction of calculation time. This method can be applied to the PCB design which needs a lots of repetitive calculation of board impedances.

• Journal of Preventive Medicine and Public Health
• /
• v.35 no.1
• /
• pp.65-71
• /
• 2002

Objective : To estimate the status of HIV infection and AIDS incidence using a back-calculation model in Korea. Methods : Back-calculation is a method for estimating the past infection rate using AIDS incidence data. The method has been useful for obtaining short-term projections of AIDS incidence and estimating previous HIV prevalence. If the density of the incubation periods is known, together with the AIDS incidence, we can estimate historical HIV infections and forecast AIDS incidence in any time period up to time t. In this paper, we estimated the number of HIV infections and AIDS incidence according to the distribution of various incubation periods Results : The cumulative numbers of HIV infection from 1991 to 1996 were $708{\sim}1,426$ in Weibull distribution and $918{\sim}1,980$ in Gamma distribution. The projected AIDS incidence in 1997 was $16{\sim}25$ in Weibull distribution and $13{\sim}26$ in Gamma distribution. Conclusions : The estimated cumulative HIV infections from 1991 to 1996 were $1.4{\sim}4.0$ times more than notified cumulative HIV infections. Additionally, the projected AIDS incidence in 1997 was less than the notified AIDS cases. The reason for this underestimation derives from the very low level of HIV prevalence in Korea, further research is required for the distribution of the incubation period of HIV infection in Korea, particularly for the effects of combination treatments.

• Nuclear Engineering and Technology
• /
• v.53 no.1
• /
• pp.44-60
• /
• 2021

In this paper, we validate the decay heat calculation capability via a two-step method to analyze spent nuclear fuel (SNF) discharged from pressurized water reactors (PWRs). The calculation method is implemented with a lattice code STREAM and a nodal diffusion code RAST-K. One of the features of this method is the direct consideration of three-dimensional (3D) core simulation conditions with the advantage of a short simulation time. Other features include the prediction of the isotope inventory by Lagrange non-linear interpolation and the use of power history correction factors. The validation is performed with 58 decay heat measurements of 48 fuel assemblies (FAs) discharged from five PWRs operated in Sweden and the United States. These realistic benchmarks cover the discharge burnup range up to 51 GWd/MTU, 23.2 years of cooling time, and spanning an initial uranium enrichment range of 2.100-4.005 wt percent. The SNF analysis capability of STREAM is also employed in the code-to-code comparison. Compared to the measurements, the validation results of the FA calculation with RAST-K are within ±4%, and the pin-wise results are within ±4.3%. This paper successfully demonstrates that the developed decay heat calculation method can perform SNF back-end cycle analyses.

• The Journal of the Acoustical Society of Korea
• /
• v.25 no.2
• /
• pp.61-71
• /
• 2006

An MP3 encoder chip has been designed and fabricated with the hardware and software co-design concepts. In the aspect of the software. the calculation cycles of the distortion control loop. which requires most of the calculation cycles in MP3 encoding procedure. have been reduced to $67\%$ of the original algorithm through the 'scale factor Pre-calculation'. By using a floating Point 32 bit DSP core and designing the FFT block with the hardware. we can get the additional reduction of the calculation cycles in addition to the software optimization. The designed chip has been verified using HW emulation and fabricated via 0.25um CMOS technology The fabricated chip has the size of $6.2{\time}6.2mm^2$ and operates normally on the test board in the qualitative and quantitative aspect.

• Journal of Welding and Joining
• /
• v.6 no.4
• /
• pp.35-43
• /
• 1988

Welding residual stresses were calculated by two dimensional thermal elasto-plastic analysis using element method. Complicated plastic behavior during heat transfer was simulated with time. Fist, temperature distributions. To consider time varying behavior of material properties and loading and unloading processes, iterative calculation based on initial stiffness method was carried out. The method proposed by Yamata was used in time increment control which determined the accuracy of claculation. comparison with other caculated and experimental results shows fairly good agreement.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.12
• /
• pp.161-167
• /
• 1999

This paper describes the calibration method and the calculation equations of expanded uncertainty for a precision electric force measuring device. The calibration of the electric force measuring device is performed three times (0 ${\circ}$(first time), $120{\circ}$(second time), $240{\circ}$(third time)) at each calibration point. It is usually selected ten points from zero load to rated load of the electric force measuring device. The expanded uncertainty is calculated by combining A type standard uncertainty and B type standard uncertainty. The calibration method and the calculation equations of expanded uncertainty can be widely used in the calibration of the precision electric force measuring device.

• KIEAE Journal
• /
• v.10 no.4
• /
• pp.3-8
• /
• 2010

Recently, various daylight evaluation methods for visual environment have been developed; simulation analysis methods, numerical calculation, and data monitoring methods. However, it is impossible for simulation analysis to make real scenes and visualize real images exactly. Also, a numerical calculation is considered as an out of date and time-consuming mean. Therefore, for acquisition of accurate results, many studies often use the monitoring data methods. Especially, most studies regarding discomfort glare are evaluated by measuring the physical quantity of luminance through traditional measuring Minolta Luminance meters as an instrument. But, this method has a difficulty in measuring several points at the same time because of the limitation of spaces and time when mapping. So, this study focused on the potential usefulness of High Dynamic Range photography technique as a luminance mapping tool. In order to evaluate the accuracy of proposed programs such as webHDR, Photomatix and PHOTOLUX, this paper has conducted an experiment by using Canon EOS 5D and NICON Coolpix8400 digital camera.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.950-955
• /
• 2001

For the development of an ultra-precision CNC polishing system including on-machine measurement system, we study a corrective polishing algorithm. We analyze and test the unit removal profiles for a ball type polishing tool. Using these results we calculate dwell time distributions and residual errors for a target removal shape. We use the polishing simulation method and feed rate calculation method for the dwell time calculation. We test corrective polishing algorithm with an optical glass. The target removal shape is a sine wave that has amplitude 0.3 micro meters. We find this polishing process has a machining resolution of nanometer order and is effective for sub-micrometer order machining. This result will be used for the software development of the CNC polishing system.