• Nuclear Engineering and Technology
• /
• v.36 no.1
• /
• pp.1-11
• /
• 2004

Two approximate methods for a cosmic radiation shielding calculation in low earth orbits were developed and assessed. Those are a sectoring method and a chord-length distribution method. In order to simulate a change in cosmic radiation environments along the satellite mission trajectory, IGRF model and AP(E)-8 model were used. When the approximate methods were applied, the geometrical model of satellite structure was approximated as one-dimensional slabs, and a pre-calculated dose-depth conversion function was introduced to simplify the dose calculation process. Verification was performed with mission data of KITSAT-1 and the calculated results were also compared with detailed 3-dimensional calculation results using Monte Carlo calculation. Dose results from the approximate methods were conservatively higher than Monte Carlo results, but were lower than experimental data in total dose rate. Differences between calculation and experimental data seem to come from the AP-8 model, for which it is reported that fluxes of proton are underestimated. We confirmed that the developed approximate method can be applied to commercial satellite shielding calculations. It is also found that commercial products of semi-conductors can be damaged due to total ionizing dose under LEO radiation environment. An intensive shielding analysis should be taken into account when commercial devices are used.

• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.311-315
• /
• 1998

Load Flow calculation methods can usually be divided into Gauss-Seidel method, Newton-Raphson method and decoupled method. Load flow calculation is a basic on-line or off-line process for power system planning, operation, control and state analysis. These days Newton-Raphson method is mainly used since it shows remarkable convergence characteristics. It, however, needs considerable calculation time in construction and calculation of inverse Jacobian matrix. In addition to that, Newton-Raphson method tends to fail to converge when system loading is heavy and system has a large R/X ratio. In this paper, matrix equation is used to make algebraic expression and then to solve load flow equation and to modify above defects. And it preserve certain part of Jacobian matrix to shorten the time of calculation. Application of mentioned algorithm to 14 bus, 39 bus, 118 bus systems led to identical result and the number of iteration got by Newton-Raphson method. The effect of time reduction showed about 28%, 30%, at each case of 39 bus, 118 bus system.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.27 no.2
• /
• pp.7-14
• /
• 2021

Purpose: The purpose of this study is to provide an effective construction project cost estimation tool for preparing a business plan of healthcare facilities which can be practically used for development projects. Methods: In order to provide a tool for calculating construction project costs, this study analyzed the Building and Related Laws, the Building Technology Promotion Laws, the Ministry of Land, Infrastructure and Transport notifications and directives, the Ministry of Trade, Industry and Energy notifications, the detailed guidelines of the Ministry of Strategy and Finance, the Building Service Industry Promotion Acts, various certification standards, actual project budget calculation cases, etc. with advices from related experts. Results: 1) Construction cost is classified into construction costs, architectural design costs, supervision costs, incidental costs, and each sub-element. In particular, since there are many incidental cost items, essential items to be reviewed during planning are derived and costs are calculated according to appropriate consideration criteria. 2) Criteria for Payment calculation mainly applies the construction cost rate method or the actual cost fixed amount method in consideration of the characteristics and scope of work. Implications: There are many calculation factors that need to be applied to the construction project cost. Therefore, it is necessary to organize the calculation process more clearly.

• Journal of Mechanical Science and Technology
• /
• v.16 no.10
• /
• pp.1296-1302
• /
• 2002

A mathematical model for cold rolling and temper rolling process of thin steel strip has been developed using the influence function method. By solving the equations describing roll gap phenomena in a unique procedure and considering more influence factors, the model offers significant improvements in accuracy, robustness and generality of the solution for the thin strip cold and temper rolling conditions. The relationship between the shape of the roll profile and the roll force is also discussed. Calculation results show that any change increasing the roll force may result in or enlarge the central flat region in the deformation zone. Applied to the temper rolling process, the model can well predict not only the rolling load but also the large forward slip. Therefore, the measured forward slip, together with the measured roll force, was used to calibrate the model. The model was installed in tile setup computer of a temper rolling mill to make parallel setup calculations. The calculation results show good agreement with the measured data and the validity and precision of the model are proven.

• Journal of Welding and Joining
• /
• v.10 no.2
• /
• pp.32-42
• /
• 1992

A method of optimization of process parameters in Arc Welding has been discussed in this paper. The method of investigation is based on the numerical calculation of weld bead by a finite element method and non-linear optimization technique is applied to estimated the optimization process parameters from the numerical calculation. The common package program(ANSYS 4.4A) was used to obtain the process parameters for a thin plate arc welding (TIG, CO$_{2}$). The results on some test are satisfactory and the used method of this paper is a useful guide to the optimum welding condition.

• Journal of the Korean Solar Energy Society
• /
• v.30 no.6
• /
• pp.34-43
• /
• 2010

Recently environmental regulations like the Kyoto Protocol, adopted in 1997, required the reduction of the greenhouse gas of 5.2% up to 1990 regulations. and 13th General Assembly in 2007, held in Bali of India, have agreed to duty reduction even in developing countries in 2013. Because of the lack of information about real process in small or middle size industries, most recent research omitted to calculate green house gas emissions from the industrial process. Bottom-up methodology will be applied for calculation of green house gasemission from industry sector to solve these problems in this research. Total amount from industry sector of Shicheung-City in 2007 was about 1,797,305 tons of greenhouse gas $CO_2$ and 3,049,403 tons of the greenhouse gas $CO_2$ calculated from industry sector of Ansan-City in 2007.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.679-682
• /
• 1995

The observed high-field magnetization curves of $Sm_{2}Fe_{17}N_{3.0}$ at 4.2 K and 296 K are well reproduced by the calculation using the Sm-Fe exchange field $2\mu\textrm{B}H_{ex}\;=\;320\;K$ and two crystalline electric field parameters ${A_{0}}^{2}=\;-910\;K$ and ${A_{1}}^{0}=\;200\;K$. The calculation shows that during the magnetization process along the hard axis at 4.2 K, the Sm moment rotates toward the direction antiparallel to H when H < 110 kOe and then returns to the field direction with further increase of the field. At 296 K, the Sm moment rotates toward the direction antiparallel to H monotonously with increasing field and finally becomes antiparallel to H when $H{\geq}H_{A}=210\;kOe$. The particular magnetization process of the Sm moment can be explained by the field-induced noncollinear coupling between the spin and orbital moments of the Sm ion.

• Transactions of Materials Processing
• /
• v.30 no.4
• /
• pp.186-194
• /
• 2021

Finite element simulation is a widely applied method for practical purpose in various metal forming process. However, in the simulation of elasto-plastic behavior of porous material or in crystal plasticity coupled multi-scale simulation, it requires much calculation time, which is a limitation in its application in practical situations. A machine learning model that directly outputs the constitutive equation without iterative calculations would greatly reduce the calculation time of the simulation. In this study, we examined the possibility of artificial intelligence based constitutive equation with the input of existing state variables and current velocity filed. To introduce the methodology, we described the process of obtaining the training data, machine learning process and the coupling of machine learning model with commercial software DEFROM^TM, as a preliminary study, via rigid plastic finite element simulation.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.12 no.1
• /
• pp.60-70
• /
• 2020

The outfitting design of ships and offshore structures is mainly undertaken in a restricted space. Pipes occupying a large portion of outfitting design are normally manufactured outside the shipyard. This complicated manufacturing process results in frequent delivery delays. Inevitable design modifications and material changes have also resulted in inefficient pipe installation works. In this study, an algorithm is proposed to systematically determine the pipe installation sequence. An accurate and fast algorithm to identify the geometric relationship of piping materials is presented. To improve the calculation efficiency, the interference is gradually examined from simplified to complicated shapes. It is demonstrated that the calculation efficiency is significantly improved with successive geometric operations such as back-face culling and use of bounding boxes. After the final installation sequence is determined, the entire installation process is visualized in a virtual reality environment so that the process can be rendered and understood for a full-scale model.

• Journal of information and communication convergence engineering
• /
• v.19 no.2
• /
• pp.102-107
• /
• 2021

In this paper, we propose a new three-dimensional (3D) photon-counting integral imaging reconstruction method using a merging reconstruction process and maximum likelihood estimation (MLE). The conventional 3D photon-counting reconstruction method extracts photons from elemental images using a Poisson random process and estimates the scene using statistical methods such as MLE. However, it can reduce the photon levels because of an average overlapping calculation. Thus, it may not visualize 3D objects in severely low light environments. In addition, it may not generate high-quality reconstructed 3D images when the number of elemental images is insufficient. To solve these problems, we propose a new 3D photon-counting merging reconstruction method using MLE. It can visualize 3D objects without photon-level loss through a proposed overlapping calculation during the reconstruction process. We confirmed the image quality of our proposed method by performing optical experiments.