• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.812-813
• /
• 2011

This paper presents the characteristic of newly developed electrical steel and motor performance analysis for HEV/EV. This material is developed and optimized for high frequency operation to reduce the core losses in traction motors to increase fuel efficiency. Four types of electrical steel are introduced, which are optimized for high flux density (PNHF), high frequency low core loss (PNF), high punchability (PNS) and high strength (PNT) to meet different specifications from different types of traction motors. To identify the motor performance with this material, finite element analysis was used to calculate core loss as well as Ld and Lq for efficiency map. Also structure analysis was performed to calculate stress on bridge rotor.

• Computational Structural Engineering
• /
• v.9 no.4
• /
• pp.173-179
• /
• 1996

Study of weldment fracture behavior includes thermal analysis, residual stress analysis, and fracture analysis. The J-integral loses its path-independency in a residual stress field. Therefore, it is necessary to develop a program to calculate the J-integral in a welded plate. In this study, theoretical formulation and program were developed for the evaluation of the J-integral at the crack tip of weldments. To verify equations and program, welded thin plate and thick plate were used to calculate residual stress and the J-integral.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.66 no.4
• /
• pp.219-223
• /
• 2017

In this paper, we calculated the losses in the high voltage lines of power distribution system. The losses caused by high voltage lines are calculated using maximum current, resistance, loss factor, and dispersion loss factor. The accurate extraction of these factors are very important to calculate the losses exactly. Thus, the maximum loads are subdivided to regions and calculated monthly for more accurate maximum current calculation. Also, the composite resistance is calculated according to the ratio of the used wire types. In order to calculate the loss factor, the load factors according to the characteristics of each region were calculated. Finally, the losses of the distribution system is calculated by adding the losses by the transformers and the low voltage lines.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.10a
• /
• pp.383-386
• /
• 2009

Contract power conversion factor which is applied to estimate contract power of industrial customers is an important standard to calculate transformer capacity. This paper shows a reasonable contract power conversion factor, that was made by the systematic and statistical way considering actual conditions, such as investigated contract power and peak power for the last 5 years of each customer for industrial customers as to AMR system. In this dissertation, it is necessary to analyze the key features and general trend from the investigated data. It made an analysis of the feature parameters, such as average, standard deviation, median, maximum. minimum and thus it was carried the linear and nonlinear regression analysis. Therefore, this paper compared characteristics for a contract power conversion factor which is applied to calculate contract power with characteristics for a regression model for customers which maximum utilization factor of transformer is more than 60%.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.703-705
• /
• 1992

In this paper, we calculate the inductance and resistance of the electromagnetic launcher by means of the 3D FEM and the analytical method. And, the dynamic models of the electromagnetic launcher are presented to calculate it's performance. We compared the analysis results with the experimental results and conclude that the presented analysis methods are reasonable.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.12
• /
• pp.3357-3368
• /
• 1994

Total pressure losses required to calculate the total-to-total efficiency are estimated by integrating empirical loss coefficients of four loss mechanisms along the mean-line of blades as follows; blade profile loss, secondary flow loss, end wall loss and tip clearance loss. The off-design points are obtained on the basis of Howell's off-design performance of a compressor cascade. Also, inlet-outlet air angles and camber angle are obtained from semi-empirical relations of transonic airfoils' minimum loss incidence and deviation angles. And nominal point is replaced by the design point. It is concluded that relatively simple loss models and Howell's off-design data permit us to calculate the off-design performance with satisfactory accuracy. And this method can be easily extended for off-design performance prediction of multi-stage compressors.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.9
• /
• pp.1306-1313
• /
• 2004

This paper addresses a theoretical approach to calculate the amount of the stored energy during high strain-rate deformations using atomistic level simulation. The dynamic behavior of materials at high strain-rate deformation are of great interest. At high strain-rates deformations, materials generate heat due to plastic work and the temperature rise can be significant, affecting various properties of the material. It is well known that a small percent of the energy input is stored in the material, and most of input energy is converted into heat. However, microscopic analysis has not been completed without construction of a material model, which can simulate the movement of dislocations and vacancies. A major cause of the temperature rise within materials is traditionally credited to dislocations, vacancies and other defects. In this study, an atomistic material model for FCC such as copper is used to calculate the stored energy.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.3
• /
• pp.73-78
• /
• 2011

This study contains to theory and analysis research for the stress and the translation of an expand disk that fix a ring gear for tooth profile machining. The stress of the expand disk is analysed by the finite element method(FEM) to calculate design parameters. From the analysis results, the stress of the expand shows a linear tendency under various fixing force. This results show that the expand disk have a elastic characteristics as a disk spring. The maximum stress was observed on under side in split section of the expand disk. It is verified that the analysis results are useful to calculate design parameters of the expand disk.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.596-601
• /
• 2007

A simplified finite element analysis method is proposed to calculate elasto-plastic responses of general hardening materials. The method provides an effective tool to calculate structural elasto-plastic responses. Numerical examples have demonstrated that its computational efficiency is very much higher than that of the incremental elasto-plastic finite element analysis, and computational results are accurate enough to meet the need of engineering practice. Compared with the general elasto-plastic incremental finite element analysis, the proposed method can avoid the incremental iteration of nodal displacements and the constitutive equation integration at each Gauss integral point, and computational results are accurate enough to meet the need of engineering practice.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.1
• /
• pp.32-38
• /
• 2005

Generally, cutting force models use a sin function method to calculate chip thickness. In slot end milling, the error from a sin function method is much bigger than other machining because a tool rotation angle in cutting is much larger. Thus in this paper, a new method to calculate chip thickness was suggested and evaluated. In a new method, tool position data according to tool rotation are checked and stored so that it is possible correct chip thickness is calculated. Cutting force waveforms simulated from a sin function method and a new method and measured waveforms from experiments were compared and error percentages were obtained. Finally, a new method had good results for simulating cutting force in slot end milling.