• 대한기계학회논문집A
• /
• 제24권2호
• /
• pp.535-542
• /
• 2000

This paper presents a method for the dynamic analysis of constrained multibody systems undergoing abrupt collision. The proposed method uses a longer time interval to check collision than that of c onventional method. This reduces the computational effort significantly. To calculate collision points on two colliding rigid bodies, one may introduce constraints of contact. However, this causes reduction of degree of freedom and difficulty of numerical analysis. The proposed method can calculate collision points without above mentioned problems. Three numerical examples are given to demonstrate the computational efficiency and the usefulness of the proposed method.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.148-153
• /
• 2004

This paper represents that parts of a large generator operating in 1000 MW are affected by centrifugal forces due to high-speed rotation in 3600 rpm and 3D FEM Analyses are required to obtained the structural reliability of the generator. From these results, one would know the weakest locations and the stress distributions. The fatigue life is calculated in order to grasp the remaining life of generator. 2D and 3D analyses are performed to calculate stresses of the generator rotor and the retaining ring. From 2D results, we find the SCF at the slot and sub-slot of the rotor. 3D analysis is applied at the end part of generator rotor, which represents complex geometry, and rotor and retaining ring shrink thermally. With these results, designers of rotor and retaining ring can compare with the results of design code and verify the stress distributions of generator rotor and retaining ring, and then calculate the remaining life from the low-cycle fatigue data.

• 환경영향평가
• /
• 제10권1호
• /
• pp.59-71
• /
• 2001

This study aims to propose a determinant model to select a method on calculating weight of each indicator for environmental evaluation. According to analyzing and comparing with three types of methods for calculating weights which are usually used to evaluate environment with indicators, the weights which were obtained by each type were all different from each other. This means that a differential weighting method must be applied to each of environmental evaluation studies. Therefore, a determinant model is required to determine weight-calculating methods. Three types of weighting methods, such as weighting by importance degree, weighting by eigen-value and weighting by analytic hierarchy process, were compared. Under the necessity, a determinant model was drawn for selecting a compatible method to calculate weights of indicators in environmental evaluation.

• 한국자동차공학회논문집
• /
• 제10권1호
• /
• pp.179-186
• /
• 2002

The absolute longitudinal speed of a vehicle is estimated by using vehicle acceleration data from an accelerometer and wheel speed data from standard 50-tooth antiknock braking system wheel speed sensors. An intuitive solution to this problem is, "When wheel slip is low, calculate absolute velocities from the wheel speeds; when wheel slip is high, calculate absolute velocity by integrating the accelerometer." Fuzzy logic is introduced to implement the above idea and a new algorithm of "modified velocities with step integration" is proposed. This algorithm is verified experimentally to estimate speed of a vehicle, and is also shown to estimate absolute longitudinal vehicle speed with a 6% worst-case error during a hard braking maneuver lasting three seconds.

• 한국자동차공학회논문집
• /
• 제5권5호
• /
• pp.27-36
• /
• 1997

For the strength design of the brake system of a forklift truck, a procedure to calculate the internal forces acting on the system is presented in this paper. Vehicle dynamics, brake system kinematics, and internal force equilibrium analysis are integrated into the procedure. Design parameters such as stopping distance, maximum decceleration, and maximum torque generated by pedal force are considered in the vehicle dynamics, and geometric parameters of the brake system are considered in the brake system kinematics. With the two analysis results obtained, the internal forces acting in the brake system are finally calculated in the procedure.

• 한국자동차공학회논문집
• /
• 제3권1호
• /
• pp.97-107
• /
• 1995

Global postbuckling analysis is accomplished for one-dimensional and two-dimensional delaminations. A new finite element model, which can be used to model the global postbuckling analysis of one-dimensional and two-dimensional delaminations, is presented. In order to calculate the strain energy release rate, geometrically nonlinear analysis is accomplished, and the incremental crack closure technique is introduced. To check the effectiveness of the finite element models and the incremental crack closure technique, the simplified closed-form sloution for a through-the-width delamination with plane strain condition is derived and compared with the finite element result. The finite element results show good agreement with the closed-foul1 solutions. The present method was extended to calculate the strain energy release rate for two-dimensional delamination. For a symmetric circular delamination, the strain energy release rate shows great variation along the delamination front. and the delamination growth appears to occur perpendicular to the loading direction.

• 소음진동
• /
• 제10권3호
• /
• pp.474-479
• /
• 2000

Piston slap is not only one of the major sources of noise and vibration in internal combustion engines but also a cause of the deterioration of engine performance. The basic mechanism associated with the piston slap seems to be quite simple but the phenomenon is in fact complicated with regard to many mechanical elements associated, First of all the impact force of piston slap must be identified to estimate engine block surface vibration, In this paper model of collision point is proposed to calculate the impact force when slap surface vibration. In this paper model of collision point is proposed to calculate the impact force when slap occurs. The parameters of the model are estimated by employing the concept of point mobility, . The predicted and experimentally observed vibration results confirm that the proposed method is practically useful.

• 대한음성학회지:말소리
• /
• 제51호
• /
• pp.71-84
• /
• 2004

In this paper, we propose the automatic speech database verification method(or called automatic verification) based on confidence measure for a large speech database. This method verifies the consistency between given transcription and speech using the confidence measure. The automatic verification process consists of two stages : the word-level likelihood computation stage and multi-level likelihood ratio computation stage. In the word-level likelihood computation stage, we calculate the word-level likelihood using the viterbi decoding algorithm and make the segment information. In the multi-level likelihood ratio computation stage, we calculate the word-level and the phone-level likelihood ratio based on confidence measure with anti-phone model. By automatic verification, we have achieved about 61% error reduction. And also we can reduce the verification time from 1 month in manual to 1-2 days in automatic.

• 한국정밀공학회지
• /
• 제17권4호
• /
• pp.97-105
• /
• 2000

One of the most important steps to determine the blank shape and dimensions in deep drawing process is to calculate the surface area of the product. In general, the surface area of axisymmetric products is calculated by mathematical or graphical methods. However, in the case of non-axisymmetric products, it is difficult to calculate the exact surface area due to errors as separated components. Fortunately, it is possible for elliptical products to recognize the geometry of the product in the long side and short side by drafting in another two layers on AutoCAD software. So, in this study, a surface area calculating system is constructed for a design of blank shape of deep drawing products. This system consists of input geometry recognition module and three dimensional modeling module, respectively. The suitability of this system is verified by applying to a real deep drawing product. The system constructed in this study would be very useful to reduce lead time and cost for determining the blank shape and dimensions.

• 상하수도학회지
• /
• 제12권2호
• /
• pp.76-82
• /
• 1998

It is necessary to calculate the accurate velocity from the hydraulic model for the reliable prediction of water quality changes in water supply system. To verify the hydraulic analysis of the water supply system, fluoride was used as a tracer to calculate the travel time from the injection point to the sampling points. Results from this field experiment indicate that fluoride can be a good conservative tracer while it showed a little longitudinal dispersion along the pipe lines. And the velocity from the model was verified by these travel times and calibrated by changing the ratio of the unaccountable water. When the ratio of the unaccountable water. When the ratio of the unaccountable water was 20%, the error between the estimation of hydraulic model and the real travel time was minimum.