• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.373-379
• /
• 2006

Fiber characteristics and fiber distribution of thermomechanical pulp(TMP), bisulfite chemithermomechanical pulp(bisulfite CTMP), neutral sulfite chemithermomechanical pulp(neutral sulfite CTMP) from kenaf(Hibiscus cannabinus L., Malvaceae) cultivar Tainug-2 cultivated in the reclaimed land of Korea were examined to use effectively nonwood fibers as an alternative raw material sources for papermaking. Yields of TMP and CTMP from kenaf were lower than those of TMP from hardwoods and CTMP from softwoods and hardwoods. Bark fibers of kenaf cultivar Tainung-2 ranged 2.04 to 2.30 mm long and $18.7{\sim}19.7{\mu}m$ width. Core fibers averaged 0.63 to 0.80 mm long and $29.5{\sim}31.4{\mu}m$ wide. Coarseness of bark fiber was higher than that of core fiber, and fiber from TMP were higher than those from both bisulfite CTMP and neutral sulfite CTMP. Curl indexes of bark fibers were higher than those of core fibers. However curl indexes were not significantly affected by the pulping conditions. Short fiber distributions were higher in core fibers from TMP and CTMP and long fiber distributions were higher in bark fibers. There was no significant difference in fiber distribution of whole and core fibers obtained from TMP and CTMP, Fibers from neutral sulfite CTMP, however, exhibited a little higher long fiber distribution. Distinct difference in anatomical characteristics was found between core and bast fibers of kenaf plant. Parenchyma cell, pith parenchyma cell and vessel were observed in core fibers and bast fiber in bast sections.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.4
• /
• pp.22-29
• /
• 2002

This research was conducted to investigate the morphological characteristics of fine fibers produced during beating process of high yield pulp treated with ozone and the distribution of lignin in the produced fine fibers. Thermomechanical(TMP) pulp and chemithermomechanical(CTMP) pulp of spruce and CTMP of white birch were beaten to reach 200$m\ell$ CSF, and then the fine fibers were observed using ultraviolet microscope. The fine fibers produced from TMP and CTMP of spruce using treated with ozone for 15 minutes were fragments of fiber surfaces or cell corners, and most of them contained lignin. However, lignin was not observed in the fibers after 15 minutes of ozone treatment. The fine fibers produced from CTMP of white birch were broken pieces or fragments of fiber surfaces or cell corners. The lignin was observed in the fibers until 5min of ozone treatment but no lignin was observed after 5 minutes of ozone treatment. Different morphological characteristics of TMP and CTMP explained both the different morphological characteristics and the distribution of lignin observed in the fine fibers produced from the beating process of TMP and CTMP treated with ozone.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.31 no.4
• /
• pp.41-48
• /
• 1999

This study was intended to investigated the effect of pulp type and intital calendering on the properties of recycled fiber. As the number of recycling is increased, at least by the fourth recycling , the freeness of the SW-BKP and HW-BKP increased. And then that decrease after the fifth recycling. Especially the freeness of CTMP increased more rapidly than any other pulp in first recycling. And there was no difference of freeness in all kind of pulp by initial calendering . The speed of dewatering in making sheet consistetly became slow by proceeding recycling on condition of all calendering. and the order of the speed of dewatering was as followed. CTMP>HW-BKP>SW-BKP. However in case of HW-BKP, which was low -yield pulp, the tendency of the speed of dewatering was similar to that of CTMP which was high-yield pulp and had high content lignin . There was no change of fiber length and no effect of calendering by recycling of HW-BKP and CTMP. Howeverfiber length of SW-BKP generally decreased, especially in calendering of high temperature and high pressure conditions. The WRV of SW-BKP diminished by proceeding recycling but that of HW-BKP and CTMP diminished in the first recycling and then there was no change of the WRV of HW-BKP and CTMP. The contents of fines of HW-BKP consistently decreased by the fourth recycling and then increased in the fifth recycling . On the other hand there was no tendency in the content of fines of SW-BKP and CTMP by the number of recycling.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.2
• /
• pp.75-80
• /
• 1997

This research has been examined to measure the degree of the fiber damage of ozonenation high yield pulp in the beating process. Ozone treated the TMP(Thermomechanical Pulp) and CTMP(Chemithermomechanical Pulp) of spruce and the CTMP of birch has been beaten to be reached 200ml(freeness) of its content. It had been studied the forming of fiber distribution by treatment for long fiber, short fiber, fine with the above method. As ozone treatment time gets longer, the pulp has showed the tendency of increasing the fiber content of 28, 48mesh. Ozone treated fiber has been increased long fiber content by being added softness. By given longer ozone treatment time, the TMP and CTMP of spruce has showed the decreasing of fiber content. On the contrary, CTMP of birch has showed the increasing its fiber content. It had proved that the results of difference are rather closer to the species of tree than closer to the kinds of pulp. The fiber content of over 200mesh which has created in beating process demonstrates the decreasing of its fiber content by getting longer ozone treatment time. The softness of fiber can be extracted by the lignin of fiber surface that had been formed by ozone treatment. Thus we assume that the fiber in the process of beating obtains less physical damage.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.30 no.4
• /
• pp.42-48
• /
• 1998

The bacterial cellulose(BC) has many unique properties that are potentially and commercially beneficial. In order to enhance inherently inferior physical property of chemithermomechanical pulp(CTMP) sheet, chemical pulp has been used widely. Bacterial cellulose also has an enhanced sheet strength because of its unique physical and morphological features. This study was carried out to inverstigate the effect of BC addition on physical properties of CTMP sheets. The effect of BC addition on its optical properties was also discussed. The apparent density, internal bond strength, Young's modulus, tensile strength and folding endurance of CTMP sheet are increasing with increase of BC contents. This strength increase would be attributed to the increase of relative bonding sites among pulp fibers by addition of BC which has microfibrillar structure with very high specific surface areas. There were not so significant changes in opacity of CTMP sheet upto 20% addition level of BC, while over 40% addition, the opacity gradually decreased and levelled off. Porosity is decreased with addition of BC. This decrease would be attributed to densification of sheet by fine and filamentous structure of BC fibers.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06a
• /
• pp.51-59
• /
• 2006

The surface of various mechanical pulp fibres including thermomechanical pulp (TMP), chemithermomechanical pulp (CTMP), and alkaline peroxide mechanical pulp (APMP) fibres, were characterized using SEM, AFM, and XPS. With SEM and AFM, middle lamella material was observed to be non-fibrillar, patch-like, while fibre secondary wall was observed to have a microfibrillar structure. It was found that after the first-stage refiner, lignin-rich middle lamella remainders are present on the fibre surface of all three pulps, although most of the fibre surfaces expose microfibrillar structure. After the final-stage refining, large amounts of granules are present on the TMP fibre surface. In contrast, most middle lamella remainders remain on the surface of CTMP fibres after final stage refining and even after peroxide bleaching. XPS results have confirmed that the non-fibrillar surface material is the lignin-rich middle lamella remainder., and the remainders of middle lamella contribute to the high surface lignin concentration.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06a
• /
• pp.173-176
• /
• 2006

Pyrolysis-gas chromatography (Py-GC) in the presence of organic alkali of tetrabutylammonium hydroxide (TBAH) was applied to characterize the polyphenol fragments with a carbonyl group causing different magnitude of photo-yellowing in chemithermomechanical pulp (CTMP) papers. Two different origin of CTMP papers prepared from different individuals of Eucalyptus globulus trees showing high and low yellowing after photo-irradiation was compared before photo-irradiation. As a result, 7 peaks assigned to a series of phenol compounds with a carbonyl group, derived mainly from lignin, gave significant amount of phenol compounds with a carbonyl group for the paper sample of latent high yellowing, i.e., butoxy-and syringaldehyde, butoxy-and syringylacetone, butoxy-acetoguaiacone, butoxy-acetosyringone, butoxy-acetoethylsyringone, 3-methoxy-4-butoxy butyl ester, and 3,5-dimethoxy-4-butoxy butyl ester, using Py-GC/mass spectrometry (MS). The Py-GC method combined with TBAH successfully characterized polyphenol fragments with a carbonyl group causing differ high photo-yellowing in CTMP papers using a microgram order of samples.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2000.04a
• /
• pp.82-85
• /
• 2000

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.1
• /
• pp.61-66
• /
• 2004

Bleached chemithermomechanical pulp (BCTMP) was produced from CTMP of Betula maximowicziana Regel by two staged ozone-hydrogen peroxide bleaching in order to improve the optical properties of high yield pulp. This pulp was used for the evaluation of optical properties improvement, chemical characteristics of lignin in fiber and the relationship between lignin and optical properties in fiber cell wall. Hydrogen peroxide treatment improved the brightness, but the post color number (PC No.). There was little improvement on optical properties by ozone treatment, but this could be improved more by using two staged ozone-hydrogen peroxide bleaching. The hydrogen peroxide treatment did not make any change on chemical characteristics of lignin in cell wall, but by ozone treatment, it was found that the non-aromatic conjugated structure was existed in the surface of cell wall, but this could be removed by hydrogen peroxide treatment in two staged ozone-hydrogen peroxide treatment. Therefore, the optical properties was significantly improved, due to the removal of non-aromatic conjugated structure.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.31 no.3
• /
• pp.77-82
• /
• 1999

The delignification, and optical and strength properties were determined to compare the ozone treatment effect in hardwood and softwood CTMPs. During ozone treatment, the delignificantion was much higher in hardwood pulp than in softwood pulp . The optical and strength properties which were very dependent upon the lignin content in pulp were significantly improved in the case of hardwood pulp . The ozone treatment of high yield pulp was more effective in hardwood pulp than that of softwood pulp.