• Journal of the Mineralogical Society of Korea
• /
• v.9 no.2
• /
• pp.102-112
• /
• 1996

The precious serpentine, referring to a rare and highly valuable gem variety of serpentine group minerals, is found to occur in serpentinite from Booyo Gren Jade Mine which is located in Oesan-myun, Booyo-gun of Chungchungnam-do. Geommological properties of the precious serpentine have been investigated by use of polarizing microscope, specific gravity balance, refractometer, hardness pencils, X-ray diffractometer, XRF, ICP-MS analyser, and infrared absorption spectroscope.The precious serpentine from Booyo is colored deep green with oily luster and semi-transparent. It is highly tough and Mohs's scale of hardness is measured to be 5-6. Specific gravity is determined to be 2.67, and a single refractive index ND=1.56 is observed by a spot method, using sodium light source. X-ray powder diffraction data is represented by the reflection lines at 7.40(100), 4.64(25), 3.68(68), 2.757(69), 2.530(49), 2.549(32), and 1.710(21${\AA}$), which compares very well with that of antigorite of serpentine group minerals. The major chemical compositions of the precious serpentine group minerals. The major chemical compositions of the precious serpentine are SiO2 42.49%, MgO 39.08%, Fe2O3 3.85%, and H2O 11.87%. Besides, trace elements such as Cr(2188), Ni(1110ppm), Co(58ppm), and Ta (108ppm) are relatively spectrum shows peaks at 3670, 1190, 1070, 980 and 610cm-1. Strong absorption at 3670cm-1 is due to OH stretching, and 1190, 1070 and 980cm-1 due to SiO stretching. The absorption 610cm-1 is formed by alteration of pre-existing ultramafic rock, namely peridotite, with an introduction of fluid with very little content of CO2, under 400$^{\circ}C$ environment. Magnetite inclusions, finely disseminated in the precious serpentine, may be a result of Fe precipitation, during serpentinization of olivine-bearing country rock.

• Restorative Dentistry and Endodontics
• /
• v.22 no.1
• /
• pp.334-346
• /
• 1997

Incidence of using esthetic composite resin in the posterior area is increasing but there were lots of inconsistent reports about their microleakage and marginal adaptation. The purpose of this study was to evaluate the differences of microleakage and marginal adaptation according to restorative techniques. 30 cavities with enamel gingival margin were prepared and restored with 3 types of composite resin [Z-100($Scotchbond^{TM}$ MP), AELITEFIL ($Onestep^{TM}$), Her culite XRV(Fuji BOND LC)] in direct technique and another 30 cavities were restored with preformed CR inlays and 3 different modern resin and resin-modified GI cements (Superbond C&B, Choice, Fuji Duet). Samples were chemically stressed in 75% ethanol for 24 hours and were thermocycled (5-$55^{\circ}C$(500 times. The degree of microleakage through proximal and gingival margins was examined by 1 % MB dye and the degree of marginal adaptation by examining the margins via SEM. The following results were obtained ; 1. In direct groups, Herculite XRV [Fuji BOND LC, 35.13 (15.50) %] group showed statistically different, less microleakage than Z-100 [$Scotchbond^{TM}$ MP, 72.91 (16.91 %] group and AELITEFIL [One-step, 93.73 (13.66) %] group (p<0.05). 2. In indirect groups, the degree of microleakage in Mean(S.D.) were: Super bond C & B [39.00 (24.35) %], Choice [57.19 (33.80) %], Fuji Duet [58.22 (40.36) %]. But there was no significant difference. 3. There was no significant difference between resin cement and resin-modified GI cement. 4. There were gaps at the interface with the tooth structure, but no gap was seen at the interface with restoration in all specimens. 5. In direct groups, Herculite XRV(Fuji BOND LC) group made little gap compared with other groups, but 40-$50{\mu}m$ thickness of bonding agent, Fuji BOND LC, looked like a cement used in indirect technique. 6. All indirect groups showed a variety of cement thickness, from less than $20{\mu}m$ to over $100{\mu}m$ and that dimension of buccal/lingual margin was less than that of gingival margin.

• Journal of Korean Society for Atmospheric Environment
• /
• v.16 no.1
• /
• pp.23-35
• /
• 2000

PM10, which is below 10 ${\mu}{\textrm}{m}$ in a diameter, has a high deposition in the lung or the bronchus by breathing and is generally composed of a lot of organic matters, viruses, algae, mold, and metallic elements that are very toxic to people. This study identified the characteristics of concentration of PM10 and air-borne jmetallic elements produced in the industrial city, Ulsan, and analyzed the correlatuion between sources and generation patterns of PM10 and metallic elements. We classified the five areas(green, residential, heavy traffic, mechanic, and petrochemcal and non-ferrous metal) which might have different characteristics of sources of PM10 and metallic elements. The average concentrations of PM10 in the five areas were as follows(petrochemical and non-ferrous metal(99.9$\mu\textrm{g}$/㎥)>mechanic(77.5 $\mu\textrm{g}$/㎥)>heavy traffic(47.1 $\mu\textrm{g}$/㎥)>residential(39.3 $\mu\textrm{g}$/㎥)>green(32.8 $\mu\textrm{g}$/㎥)). Those of petrochemical and non-ferrous metal areas were higher than other areas. In this study, the average concentration trend of metallic elements contained in PM10 are shown as follows: Fe>Zn>Pb>Cu>Mn>Cr>As>Cd>Sn>Hg, respectively. The metallic elements identified in PM10 showed the highest concentration in the petrochemical and non-ferrous areas. Metal combinations showed that a high correlation among concentrations of heavy metals were as follows: As, Cd and Fe in the residential area; Zn, Mn, Cu and Pb in the mechanical area; and Zn, Cu, As, Pb in the petrochemical and non-ferrous industrial area.

• Journal of Technologic Dentistry
• /
• v.14 no.1
• /
• pp.55-65
• /
• 1992

The purpose of this study was to investigate the comparison of physical properties of nonprecious metal alloys colored goldish yellow. The experimental groups were copper based dental alloy and control group was Ni-Cr based dental alloy used crown and bridges frameworks. Hardness was tested by vickers hardness tester, tensile strength was tested by universal tension tester. After testing the tensile strength of castings, the microstrucure and the pattern of fracture were investigated by scanning electron microscope and metallurgical microscope. The results were as follows : Hardness of Ni based alloy was higher than Cu based alloys. Hardness number of A group was 200.41$\pm$16.10 Hv, B group was 194.33$\pm$1.69 Hv, C group was 139.29$\pm$2.19 Hv and D group was 293.81$\pm$27.17 Hv, respectively. Tensile strength of D group was 56.42$\pm$6.17 $kg/m^2$, A group was 50.39$\pm$5.68 $kg/m^2$, C group was 45.13$\pm$4.53 $kg/m^2$, B group was 45.25$\pm$9.25 $kg/m^2$, in order, and D group was maximum tensile strength. The fractured surfaces of tensile specimens in the all groups showed the tendency to form large voids in the center of specimens. Thus the ductile fracture was changed into the brittle fracture with the fine grain size.

• Journal of Korean Society of Water and Wastewater
• /
• v.17 no.4
• /
• pp.542-549
• /
• 2003

In the present study, the feasibility of $UV/H_2O_2$ systems was investigated using low and medium-pressure lamps on biologically treated wastewater effluents for secondary effluent reclamation. Two types of UV lamps were used as the light sources (a 39-W low-pressure mercury lamp and a 350-W medium-pressure mercury lamp). The results from these UV systems showed that the removal of organic compounds could be achieved in the contact time of longer than 30min (i.e., low UV doses). Efficiencies of color removal and disinfection were far better than those of organic matters measured as TOC, DOC and $TCOD_{cr}$. In the low-pressure lamp UV system, it has been found that DOC and color removals were 60.9 and 86.2% with 50mg/L of $H_2O_2$ and contact times of 30 minute, respectively. Whereas, with the medium-pressure lamp UV system, TOC, DOC and color removal were 27.1, 5.6 and 95% with 14.3mg/L of $H_2O_2$ and 14 minute of contact times, respectively. Both systems could be applied for the reclamation of secondary effluent treated with biological treatment processes.

• The Bulletin of The Korean Astronomical Society
• /
• v.39 no.1
• /
• pp.70.2-70.2
• /
• 2014

We developed a three-dimensional (3D) magnetohydrodynamic (MHD) simulation code to reproduce the structure of a solar wind and the propagation of a coronal mass ejection (CME) through it. This code is constructed by a finite volume method based on a total variation diminishing (TVD) scheme using an unstructured grid system (Tanaka 1994). The grid system can avoid the singularity arising in the spherical coordinate system. In this study, we made an improvement of the code focused on the propagation of a CME through a solar wind, which extends a previous work done by Nakamizo et al. (2009). We first reconstructed a solar wind in a steady state from physical values obtained at 50 solar radii away from the Sun via an MHD tomography applied to interplanetary scintillation (IPS) data (Hayashi et al. 2003). We selected CR2057 and inserted a spheromak-type CME (Kataoka et al. 2009) into a reconstructed solar wind. As a result, we found that our simulation well captures the velocity, temperature and density profiles of an observed solar wind. Furthermore, we successfully reproduce the general characteristics of an interplanetary coronal mass ejection (ICME) obtained by the Helios 1/2 spacecraft (R. J. FORSYTH et al. 2006).

• Biomedical Science Letters
• /
• v.26 no.2
• /
• pp.120-126
• /
• 2020

Fluoroquinolone (FQ) resistant uropathogenic Escherichia coli (UPEC) have become a major problem in urinary tract infections (UTIs). The purpose of this study was to compare the quinolone resistance-determining region (QRDR) and plasmid mediated quinolone resistance (PMQR) determinants of FQ resistant UPEC between 1989 and 2010-2014. A total of 681 strains of UPEC clinical isolates was collected from Korean healthcare facility in 1989 (123 strains) and in 2010-2014 (558 strains). The minimum inhibitory concentrations (MICs) of FQs were determined by agar dilution method. QRDRs (gyrA, gyrB, parC and parE) and PMQR determinants (qnrA, qnrB, qnrS, aac(6')-Ib-cr and qepA) were analyzed polymerase chain reaction and sequencing method. Among 681 isolates, FQ resistant UPEC were 3 strains (2.4%) in 1989 isolates and 220 strains (39.4%) in 2010-2014 isolates. The rate of the FQ resistant UPEC strains in 2010-2014 isolates was increased than that of in 1989 isolates. UPEC isolates from 1989 and 2010-2014 were shown to carry mutations in gyrA (Ser83 and Asp87), gyrB (Ser464 and Thr469), parC (Ser80 and Glu84) and parE (Glu460, Ser458, Ile464 and Leu445). The most common mutations of QRDRs in 1989 isolates were Ser83Leu and Asp87Gly in gyrA and Ser80Ile in parC (2 strains: 66.7%) while those in 2010-2014 isolates were Ser83Leu and Asp87Asn in gyrA and Ser80Il2 and Glu84Val in parC (88 strains: 40.0%). PMQR determinants were detected only in 2010-2014 UPEC strains (47 strains: 21.4%).

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.15 no.1
• /
• pp.75-83
• /
• 1985

Bitewing and periapical radiographic techniques are used in clinical and epidemiological studies to assess crestal alveolar bone levels. The purpose of the present study investigated relationships between these techniques by assessing alveolar crest location at the same site. Bitewing and periapical radiographs were available from posterior quadrants of 120 subjects. The distance from cemento-enamel junction to the alveolar crest (CEJ -CR) was measured for each proximal surface from the distal of the cuspid to the distal of the second molar. Data were arranged according to the proximal surface examined, and bitewing and periapical measurements were compared using paired tests. The obtained results were as follows; 1. In maxilla, a significant t ratio with a P value of 0.05 or less was reached for 78% and in mandible reached for 39%. 2. Pearson correlations were calculated 32 surfaces (89%) had values below 0.70 and so, data obtained by these techniques can not be used interchangeably on an individual or group basis. 3. In situations where the periapical measure was greater than the bitewing, it ranged up to 20.7% greater with a mean 9.8%. Where the bitewing was greater than periapical, it ranged up to 51. 9% greater, with a mean 18.2%. 4. The percentage difference was greater in maxillary posterior areas than in mandibular molar, premolar areas. A lower prevalence of significant differences was attributed to relatively more simple root and favorable radiographic conditions in mandibular molar and premolar areas. 5. The anatomical limitations imposed on periapical radiographic technique, most often result in somewhat foreshortened radiographic images. This situation would tend to be accentuated by the anatomical restrictions of the hard palate. 6. Consequently, since the significant differences frequently exist between measurements obtained from bitewing and periapical techniques, it is important to define which technique is used.

• Journal of Embryo Transfer
• /
• v.29 no.3
• /
• pp.229-234
• /
• 2014

The aim of the present study was to compare two different serum-free media, modified synthetic oviduct fluid (mSOF) and modified potassium simplex optimization medium (mKSOM) containing 20% RD (RPMI1640 + DMEM, 1:1 v/v) (RD-mKSOM), for in vitro culture (IVC) of bovine embryos. After in vitro maturation and fertilization, the presumptive zygotes were cultured in two different serum-free conditions for 7 days and 9 days to evaluate blastocyst formation and hatching, respectively. Serum supplemented conventional CR2 medium was used as control. After 7 day of culture, there was no significant difference in cleavage and blastocyst formation rates among three groups (mSOF, 59.3 and 30.1%; RD-mKSOM, 65.0 and 41.5%; control, 51.6 and 38.0%, respectively). Hatching rate was significantly higher in control (69.0%) than other experimental groups (mSOF, 22.0%; RD-mKSOM, 39.5%) (P<0.0001 and P<0.001, respectively). Although both serum-free conditions showed lower hatching rates than serum-added control, in serum-free groups, RD-mKSOM showed significantly higher hatching rate than mSOF (P<0.001). In addition, one-step using RD-mKSOM may facilitate IVC procedure than two-step culture system. In conclusion, the results indicate that one-step RD-mKSOM is more suitable defined culture system for IVC of bovine embryos than two-step mSOF.

• Korean Journal of Materials Research
• /
• v.13 no.10
• /
• pp.645-650
• /
• 2003

The microstructure and electrical characteristics of $Pr_{6}$ $O_{11}$ -based ZnO varistor ceramics composed of $ZnO-Pr_{6}$ $O_{ 11}$/$-CoO-Cr_2$$O_3$-$Dy_2$$O_3$-based ceramics were investigated with $Dy_2$$O_3$content in the range of 0.0∼2.0 mol%. As $Dy_2$$O_3$content was increased, the average grain size was decreased in the range of 18.6∼4.7 $\mu\textrm{m}$ and the density of the ceramic was decreased in the range of 5.53∼4.34 g/㎤. While, the varistor voltage was increased in the range of 39.4∼436.6 V/mm and the nonlinear exponent was in the range of 4.5∼66.6 with increasing $Dy_2$$O_3$content. The addition of $Dy_2$$O_3$highly enhanced the nonlinear properties of varistors, compared with the varistor without $Dy_2$$O_3$. In particular, the varistor with $Dy_2$$O_3$ content of 0.5 mol% exhibited the highest nonlinearity, in which the nonlinear exponent is 66.6 and the leakage current is 1.2 $\mu\textrm{A}$. The donor concentration and the density of interface states were decreased in the range of $(4.19∼0.33) ${\times}$10^{18}$ //㎤ and $(5.38∼1.74) ${\times}$10^{12}$ $\textrm{cm}^2$, respectively, with increasing $Dy_2$$O_3$content. The minimum dissipation factor of 0.0302 was obtained from 0.5mol% $Dy_2$$O_3$.