• Korean Chemical Engineering Research
• /
• v.61 no.1
• /
• pp.52-57
• /
• 2023

This study is a basic research for the development of high performance flexible electrode material. To enhance its electrochemical property, CuO nanoparticles (CuO NPs) were introduced and dispersed on surface of CNT fiber through electrochemical deposition method. The CNT fiber/CuO NPs electrode was fabricated and applied to electrochemical non-enzymatic glucose sensor. Surface morphology and elemental composition of the CNT fiber/CuO NPs electrode was characterized by scanning electron microscope (SEM) with energy dispersive X-ray spectrometry (EDS). And its electrochemical characteristics were investigated by cyclic voltammetry, electrochemical impedance spectroscopy and chronoamperometry. The CNT fiber/CuO NPs electrode exhibited the good sensing performance for glucose detection such as high sensitivity, wide linear range, low detection limit and good selectivity due to synergetic effect of CNT fiber and CuO NPs. Based on the unique property of CNT fiber, CuO NPs were provide large surface area, enhanced electrocatalytic activity, efficient electron transport property. Therefore, it is expected to develop high performance flexible electrode materials using various nanomaterials.

• Applied Chemistry for Engineering
• /
• v.20 no.5
• /
• pp.493-499
• /
• 2009

The properties of polystyrene and styrenic copolymer nanocomposites containing carbon nanotubes (CNT) and nanoclays were studied. Polystyrene and styrenic copolymer containing styrene and vinylbenzyl trimethylammonium chloride (SVTAC) were synthesized by emulsion polymerization. Polystyrene/CNT/clay and SVTAC/CNT/clay nanocomposites with various concentrations of CNT and different types of clay were prepared via mixing of polystyrene emulsion and clay. SVTAC/CNT nanocomposites showed a better electrical conductivity than PS/CNT nanocomposites. Nanocomposites with more surfactant during polymerization showed a better electrical conductivity than the ones with less surfactant. These indicated the positive effect of comonomer and surfactant on the electrical conductivity. Transmission electron microscopy (TEM) was used to analyze the state of CNT dispersion. TEM results showed that CNT loading, comonomer composition and amount of surfactant affected the final dispersion of CNT in nanocomposites. In order to confirm the effects of CNT loading, comonomer composition and the amount of surfactant on the thermal and dynamic mechanical properties, DSC and DMA analyses were conducted.

• Polymer(Korea)
• /
• v.37 no.4
• /
• pp.526-532
• /
• 2013

The effect of CNT dispersion method on rheological and electrical properties of polystyrene/carbon nanotube (PS/CNT) nanocomposites via latex technology was compared. The nanocomposites were prepared through freeze-drying the dispersed suspension comprised of CNTs and PS particles. In this study, physical dispersion method, either sodium dodecylsulfate (SDS) addition or polyvinyl pyrrolidone (PVP) wrapping, was employed to prevent the deterioration of intrinsic properties of CNT caused by chemical modification. The physical method applied to latex technology was very effective in CNT dispersion. With SDS addition, the enhancement of rheological properties was low compared to PVP wrapping because the properties of matrix were deteriorated due to the incorporation of low molecular weight SDS. The electrical percolation threshold of PS/SDS-stabilized CNT and PS/PVP-wrapped CNT nanocomposites was 0.23 and 0.90 wt%, respectively. The enhancement of electrical conductivity was low in the case of PVP wrapping because the non-conducting PVPs wrapped around CNT restricted the electrical connection between CNTs.

• Korean Chemical Engineering Research
• /
• v.60 no.4
• /
• pp.588-593
• /
• 2022

Terephthalaldehyde (TPA) is introduced as a cross liker to enhance electron transfer of hemin-based cathodic catalyst consisting of polyethyleneimine (PEI), carbon nanotube (CNT) for hydrogen peroxide reduction reaction (HPRR). In the cyclic voltammetry (CV) test with 10 mM H₂O₂ in phosphate buffer solution (pH 7.4), the current density for HPRR of the suggested catalyst (CNT/PEI/hemin/PEI/TPA) shows 0.2813 mA cm^-2 (at 0.2 V vs. Ag/AgCl), which is 2.43 and 1.87 times of non-cross-linked (CNT/PEI/hemin/PEI) and conventional cross liker (glutaraldehyde, GA) used catalyst (CNT/PEI/hemin/PEI/GA), respectively. In the case of onset potential for HPRR, that of CNT/PEI/hemin/PEI/TPA is observed at 0.544 V, while those of CNT/PEI/hemin/PEI and CNT/PEI/hemin/PEI/GA are 0.511 and 0.471 V, respectively. These results indicate that TPA plays a role in facilitating electron transfer between the electrodes and substrates due to the π-conjugated cross-linking bonds, whereas conventional GA cross-linker increases the overpotential by interrupting electron and mass transfer. Electrochemical impedance spectroscopy (EIS) results also display the same tendency. The charge transfer resistance (R_ct) of CNT/PEI/hemin/PEI/TPA decreases about 6.2% from that of CNT/PEI/hemin/PEI, while CNT/PEI/hemin/PEI/GA shows the highest R_ct. The polarization curve using each catalyst also supports the superiority of TPA cross liker. The maximum power density of CNT/PEI/hemin/PEI/TPA (36.34±1.41 μWcm^-2) is significantly higher than those of CNT/PEI/hemin/PEI (27.87±0.95 μWcm^-2) and CNT/PEI/hemin/PEI/GA (25.57±1.32 μWcm^-2), demonstrating again that the cathode using TPA has the best performance in HPRR.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.1
• /
• pp.63-68
• /
• 2010

CNT and permalloy composite plating was investigated. CNTs were pretreated prior to electroplating to disassemble the tangled CNT lumps. The ball milling as a physical pretreatment and the acid treatment as a chemical pretreatment were used. 10M nitric acid and 10 M sulfuric acid were used for the chemical pretreatment. Sulfuric acid was more effective than nitric acid to disassemble CNT lumps. To disperse CNT in the solution, surfactants were used. SDS, Triton X-100 and PAA were used for this purpose. More CNTs were incorporated in permalloy coating when PAA was used as a surfactant. The surface morphologies were observed with FESEM after electroplating CNT and permalloy. The current densities were varied from 10 to $80\;mA/cm^2$ and the concentration of PAA was fixed at 2 g/L. The optimum current density without surface cracks was $20\;mA/cm^2$. The crystallinity of the deposit was analyzed with XRD and the surface hardness was analyzed with Vicker's hardness tester. The corrosion behavior was analyzed with polarization plot. The physical properties of permalloy were not improved with CNT composite plating.

• Clean Technology
• /
• v.28 no.4
• /
• pp.278-284
• /
• 2022

This study presents an excellent planar heater based on low-dimensional composites. By optimizing the ratio of 1D carbon nanotubes (CNT) and 2D MXene (Ti₃C₂T_X), it is possible to create a planar heater that has superior electrical conductivity and high heat generation characteristics. Low-dimensional composites were prepared by mixing CNT paste and MXene solution with eco-friendly waterborne polyurethane (WPU). In order to find the optimal mixing ratio for the MXene-CNT-WPU composites, samples with MXene to CNT weight ratios of 3:1, 1:1, 1:3, 1:7, and 1:14 were investigated. In addition to these different weight ratios, 5 wt% WPU was equally applied to each sample. It was confirmed that the higher the weight ratio of CNT, the lower the sheet resistance and the higher the heating temperature. In particular, when the MXene-CNT-WPU planar heater was fabricated by mixing MXene and CNT at a weight ratio of 1:7 and 1:14, the heating temperature was higher than the heating temperature of a CNT-WPU planar heater. These characteristics are due to the optimized mixture of the 1D materials (CNT) and the 2D materials (MXene) causing the formation of a flat surface and a dense network structure. The low-dimensional composites manufactured with the optimized mixing ratios found in this study are expected to be applied in flexible electronic devices.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.3
• /
• pp.39-44
• /
• 2015

We investigated the effect of CNT-Ag composite pad on the contact resistance of flip-chip joints, which were formed by flip-chip bonding of Cu/Au chip bumps to Cu substrate metallization using anisotropic conductive adhesive. Lower contact resistances were obtained for the flip-chip joints which contained the CNT-Ag composite pad than the joints without the CNT-Ag composite pad. While the flip-chip joints with the CNT-Ag composite pad exhibited average contact resistances of $164m{\Omega}$, $141m{\Omega}$, and $132m{\Omega}$ at bonding pressures of 25 MPa, 50 MPa, and 100 MPa, the flip-chip joints without the CNT-Ag composite pad had an average contact resistance of $200m{\Omega}$, $150m{\Omega}$, and $140m{\Omega}$ at each bonding pressure.

• Composites Research
• /
• v.24 no.4
• /
• pp.5-10
• /
• 2011

As environmental pollution getting worse, biodegradable materials have been drawn more attention than ever. In this study, polylactic acid (PLA)/carbon nanotubc (CNT) nanocomposites were manufactured via extrusion molding and injection molding, In order to change the crystallinity, annealing treatment was done for different time span, Crystallization kinetics of PLA was analyzed by differential scanning calorimeter (DSC), and it was confirmed that a proper amount of CNT can increase the crystallization rate of PLA. In addition, the presence of CNT significantly accelerates the hydrolytic degradation rate of PLA, however, it decreases with the increase of crystallinity. The reason is that degradation may occur in the PLA/CNT interface easily, and the molecular structure of the composite becomes dense with the increase of crystallinity.

• Korean Journal of Materials Research
• /
• v.26 no.9
• /
• pp.468-471
• /
• 2016

$SnO_2:CNT$ thick films for gas sensors were fabricated by screen printing method on alumina substrates and were annealed at $300^{\circ}C$ in air. The nano $SnO_2$ powders were prepared by solution reduction method using tin chloride ($SnCl_2.2H_2O$), hydrazine ($N_2H_4$) and NaOH. Nano $SnO_2:CNT$ sensing materials were prepared by ball-milling for 24h. The weight range of CNT addition on the $SnO_2$ surface was from 0 to 10 %. The structural and morphological properties of these sensing material were investigated using X-ray diffraction and scanning electron microscopy and transmission electron microscope. The structural properties of the $SnO_2:CNT$ sensing materials showed a tetragonal phase with (110), (101), and (211) dominant orientations. No XRD peaks corresponding to CNT were observed in the $SnO_2:CNT$ powders. The particle size of the $SnO_2:CNT$ sensing materials was about 5~10 nm. The sensing characteristics of the $SnO_2:CNT$ thick films for 5 ppm $H_2S$ gas were investigated by comparing the electrical resistance in air with that in the target gases of each sensor in a test box. The results showed that the maximum sensitivity of the $SnO_2:CNT$ gas sensors at room temperature was observed when the CNT concentration was 8wt%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.396-396
• /
• 2008

투명 전도성 탄소나노튜브(carbon nanotube, CNT) 필름을 터치스크린이나 디스플레이 소자 등의 전극에 응용할 목적으로, CNT 필름의 전기저항 및 광 투과도를 향상시키기 위한 연구가 활발히 진행되고 있다. 본 연구에서는 단일벽 CNT (single-walled CNT)를 여러 가지 계면활성제로 분산시킨 수용액으로부터 제조한 CNT 필름을 산 처리하여 저항 및 투과도의 변화를 관찰하였다. 우선 계면활성제로 분산시킨 CNT 수용액을 알루미나 재질의 필터에서 정량적으로 진공 필터링하여 CNT 필름을 제조하였다. 알루미나 필터를 sodium hydroxide (NaOH) 수용액으로 용해시켜 제거함으로써 얻은 CNT 필름을 유리기판 위에 부착시킨 후 광 투과도와 먼 저항 (sheet resistance)을 측정하였다. CNT 필름을 질산 ($HNO_3$) 용액에 처리하였을 때 투과도는 1~5 % 향상되었으며, 면 저항은 계면활성제로 분산시킨 CNT 필름 대부분에서 감소하였다. 이는 CNT 표면에 코팅되어 있던 계면활성제들이 산에 의해 제거되었기 때문일 것으로 추측된다. 특히 sodium dodecylbenzene sulfonate (NaDDBS)로 제조한 CNT 필름의 경우, 질산을 처리 전에는 투과도 83%, 면 저항 450 $\Omega$/sq.의 특성을 보였으나, 처리 후에는 각각 86 %, 350 $\Omega$/sq.로 향상되었다. Polyvinyl pyrrolidone (PVP)과 cetyltrimethylammonium bromide (CTAB)를 사용하여 제조한 CNT 필름의 면 저항이 가장 뚜렷한 감소를 보였다. 제조된 필름과 삼 처리된 필름 특성을 Raman spectroscopy, scanning electron microscopy, UV-Vis spectroscopy 등을 이용하여 분석하였고, 4-point probe로 면 저항을 측정하였다.