• Korean Journal of Poultry Science
• /
• v.40 no.3
• /
• pp.253-262
• /
• 2013

This experiment was conducted to investigate the effects of floor type and heating system on performance, housing environment and health status of ducks reared in three types of duck house (OD : Open floor house-Direct heating system, OF : Open floor house-Floor heating system and LD : Loft type house-Direct heating system). In OF treatment, PVC pipes were installed for heating under concrete floor and covered with litter. In LD treatment, plastic mesh was installed 50 cm above the floor so that duck's droppings can pass through it. Each treatment had four replicates of 25 birds (Cherry Valley duck breed) per pen. There were no significant differences in weight gain and feed intake of ducks for 6 weeks among all treatments. However, feed conversion ratio in LD was significantly higher (p<0.05) than that in OF. No differences were found in carcass charac- teristics, with the exception of abdominal fat weight where OF were higher than the others. Concentrations of $CO_2$ and $NH_3$ gas in OD were higher than those of OF and LD at 3, 4 and 5 weeks. Moisture content in litter of OF was lower than that of OD. In contrast, the amount of dust in the air was higher in OF than in OD. The amount of fuel used for 6 weeks in LD was lower about 21% than that in OD. Some of unusual symptoms were observed in open floor house and loft type house, such as lying, spraddle legged, twisted ankle and legs, wounded sole, or etc. No components of leukocyte and erythrocyte of blood were significantly different among all treatments. The results of this experiment showed that OF and LD systems had no positive effects on performance of meat type commercial duck. However, there were some positive effects of certain house type for the improvement of environmental condition in duck house for hygienic production. In the future, more research on the effect of various facilities and systems for duck house is needed.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.6
• /
• pp.414-420
• /
• 2012

In an effort to commercialization of energy saving aeration apparatus, panel-type aeration membranes were prepared from polyurethane sheet of J company in Korea having tensile strength higher than $400kg_f/cm^2$ with thickness of 0.5mm. Micropores of 100 m size were made by poring technique utilizing needles. From lab-tests in 450 L water tank at temperature of $20^{\circ}C$, the performance of aeration panels at 40 L/min aeration rate showed 5 mg/L DO in less than 3 minutes approaching saturation point of 8 mg/L within 8 minutes. The results show very high efficiency with $K_{La(15)}$ ($16.34hr^{-1}$), Standard oxygen transfer efficiency (SOTE 54.7%) and Standard aeration efficienct (SAE 7.88 kg/kwh). Other pilot scale test in a $2m^3$ water tank with water temperature ($19^{\circ}C$) and aeration rate (30 L/min) showed DO exceeding 5 mg/L within 8 minutes along with $K_{La(15)}$ ($5.8hr^{-1}$), SOTE (42.1%) and SAE (6.41 kg/kwh). These efficiencies represent 2~2.5 times higher than conventional aeration devices. Especially, the achievement of higher Oxygen Transfer Rate indicate higher commercial viability. Conventional aeration devices when applied to clean water and wastewater frequently cause problems due to differences in actual Oxygen Transfer Rate. Our actual tests with $40^{\circ}C$ animal farm wastewater resulted very high efficiencies with Oxygen transfer efficiency ($OTE_f$ 22.1%) and $OTE_{pw40}$ (39.6%).

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.43 no.1
• /
• pp.135-140
• /
• 2014

Pre-storage ultra-violet (UV) light treatment on fresh produce is known to inactivate the contaminated microorganisms, activate the defense system, and delay ripening extending the shelf life. As UV light emitting diode (LED) becomes available at a relatively low price, continuous or intermittent UV treatment during chilled storage is possible in a container or package. This study attempted an in situ UV LED treatment on fresh produce stored under a refrigerated container in order to see its potential in the fresh produce storage and further optimize its application conditions. The effect of in-container UV LED irradiation on the quality preservation of shredded carrots was investigated in the air and modified atmosphere (MA) conditions. Two sets of experiment with Escherichia coli inoculation and with natural microbial flora in the air (two 30 minute on-off cycles of 1 $diode/dm^2$ per day at a location above 2 cm) showed a clear and significant effect of the UV LED irradiation on the suppression of microbial growth: 280 nm was the most effective by maintaining a lower microbial count by at least 0.5 log (CFU/g) throughout the 6 day storage period. The carotenoids content of shredded carrots subjected to UV LED treatment at 365 and 405 nm in the air was higher than that of the control shredded carrots. In MA condition of $O_2$ of 1.2~4.3% and $CO_2$ of 8.4~10.6% being indifferent with LED wavelengths, 280 nm UV LED irradiation was also effective in inhibiting the microbial growth. While there was no observed difference in the carotenoids content between untreated and UV LED-treated shredded carrots in MA, UV LED irradiation at 365 and 405 nm was slightly better in DPPH radical scavenging activity. The use of UV LED in storage container or package seems to give the benefits of preserving the microbial and nutritional qualities of minimally processed fruits and vegetables.

• Journal of Plant Biology
• /
• v.24 no.1
• /
• pp.47-57
• /
• 1981

Girth at breast height was measured to test skewness ($g_1$) and kurtosis ($g_2$) of frequency distribution of the basal area in terms of t-test and Kolmogorov-Smirnov test for a total of forty six monocultures within Sudong and Kwhangnung area in central part of Korean peninsula in 1979 and 1980. The monocultures are about 10 to 50 years old, and four kinds: Pinus koraiensis, Larix kaempferi, Abies holophylla and Pinus rigida. Most of the sample sizes per site were ranged 70 to 110 excluding 4 sites. The number of classes interval was based on Sturges rule for each monoculture and was ranged from 5 to 10. In Sudong the range of age(yr) and basal area (($cm^2$)/tree) of the monocultures were from 10 to 20 and from 27.60 to 383. for Kwhangnung they were from 15 to 47 and mostly 102.15 to 619.14, respectively. All 43 monocultures except 1 showed +$g_1$, which ranged from 0.3 to 2.2 except six sites. Of the total 46 sites, 23 sites showed significant +$g_1$ which includes about 10 year-old monoculture. The number of classes interval with significant positive skewness ranged from 6 to 9. The data suggest that intraspecific competition in terms of stand structure seems to appear from about 10 year-old monocultures, and it may even last to about 50 year-old one. Around 24 monocultures showed nonsignificant -$g_2$ except one. Most -$g_2$ ranged from -0.12 to -0.83. Around 20 monocltures showed positive $g_2$ ranging from +0.13 to +3.841. Of the 22 +$g_1$, majority of 11 were very highly significant. Of all monocultures only 5 showed significant result from Kolmogorov-Smirnov test. Of the 4 species, Larix kaempferi seems to show density stress first then Abies holophylla, and Pinus koraiensis last. Data of this study indicate that adequate number of classes intervals and sample sizes for studying intraspecific competition in terms of basal area are 6 to 9 and 80 trees rather than 12 and 100 trees, respectively. It also suggests that most of the frequency distribution of basal area class are trimodal rather than bimodal under density stress. It is proposed that the leptokurtic distribution appears before normal distribution rather than direct change from platykurtic to normal distribution of basal area for selected stages in the development of stands.

• Economic and Environmental Geology
• /
• v.47 no.6
• /
• pp.611-623
• /
• 2014

The alluvial aquifer, widely developed near the four major rivers such as Nakdong River, can be used effectively for groundwater artificial recharge and is expected to be the future water resources in Korea. This study is aimed at examining the impact of repeatedly injected river water into the riverside alluvial aquifer on injection rate or efficiency in its system at Changweon area. For this, injection tests were performed two times, first on June 19 and second on September 25 through October 9, 2013, and the mixing ratios of river water to groundwater were used as the tool to compare the efficiency of injection. The mixing ratios were evaluated by using electrical conductivities of injected river water (average $EC=303{\mu}S/cm$) and groundwater ($EC{\fallingdotseq}6,000{\mu}S/cm$) measured at 20 m depth of four observation wells installed 10 m apart from each injection well. The result shows the remarkable differences on two respects. First, in some observation well, detection time for incipient injection effect during $2^{nd}$ injection test was shown to be much slower than that of $1^{st}$ injection test. Second, the hourly increasing rate of mixing ratios in $2^{nd}$ test was revealed to be reduced much more than that of $1^{st}$ test. This means that the efficiency of injection was badly deteriorated by only 1,210 minute injection work. Therefore, injection water needs to be adequately treated beforehand and repeated pumping work and/or resting phase is needed afterwards. To a certain extent, the improvement of water quality in saline aquifer was verified in this system by injection tests.

• Analytical Science and Technology
• /
• v.25 no.2
• /
• pp.121-126
• /
• 2012

It is essential to evaluate the quality of Hanji record paper without damaging the record paper by previous destructive methods. The samples were Hanji record paper produced in the 1900s. Near-infrared (NIR) spectrometer was used as a non destructive method for evaluating the quality of record papers. Fourier transform (FT) spectrometer was used with 12,500 to 4,000 $cm^{-1}$ wavenumber range for quantitative analysis and it has high accuracy and good signal-to-noise ratio. The acidity and moisture content of Hanji record paper were measured by integrating sphere as diffuse reflectance type. The acidity (pH) of chemical factors as a quality evaluated factor of Hanji was correlated to NIR spectrum. The NIR spectrum was pretreated to obtain the coefficients of optimum correlation. Multiplicative scatter correction (MSC) and First derivative of Savitzky-Golay were used as pretreated methods. The coefficients of optimum correlation were calculated by PLSR (partial least square regression). The correlation coefficients ($R^2$) of acidity had 0.92 on NIR spectra without pretreatment. Also the standard error of prediction (SEP) of pH was 0.24. And then the NIR spectra with pretreatment would have better correlation coefficient ($R^2$ = 0.98) and 0.19 as SEP on pH. For moisture contents, the linearity correlation without pretreatment was higher than the case with pretreatment (MSC, $1^{st}$ derivative). As the best result, the $R^2$ was 0.99 and SEP was 0.45. This indicates that it is highly proper to evaluate the quality of Hanji record papers speedily with integrated sphere and FT NIR analyzer as a non-destructive method.

• Journal of Nutrition and Health
• /
• v.45 no.5
• /
• pp.489-499
• /
• 2012

The purpose of this study is to present basic data for an improvement of school foodservice by identifying students' preference level for school meal menu. A survey was carried out in two high schools provided with different types of consignment service in Daegu. Study subjects were consisted of 100 high school students from a school with on-site service and 119 students from the other school with external transporting service. More than half of students (54.2% of male and 68.3% of female) had normal weights while 13.5% of male and 30.1% of female students had underweights. 'Taste' and 'family' were the most important factors in meal choices and in eating habits, respectively of all the study subjects. Students who answered to have unbalanced diet (33.0%) were less in school with on-site service than those (56.1%) with external transporting service. Compared with on-site service, preferences for meats fruit and milk were higher and as cooking method, preference for blanching lower but stew, roasting and frying higher in the school with external transporting service. Various types of cooking methods and food materials were better accepted by the students with on-site service than those with external transporting service who preferred meat more exclusively regardless of cooking methods of main dish. Most kinds of kimchi was less liked by the students with external transporting service. It is concluded that low preference for most menus provided by the external transporting service is attributed by limitation in food materials, cooking methods and maintenance of food temperature. The limitation could be overcome by more intensive efforts for developing menus and using more efficient facilities and ultimately by changing meal service system in cooperation with school administrators, dietitians and parents.

• Journal of Bio-Environment Control
• /
• v.28 no.4
• /
• pp.279-285
• /
• 2019

To estimate daily canopy photosynthesis, accurate estimation of canopy light interception according to a daily solar position is needed. However, this process needs a lot of cost, time, manpower, and difficulty when measuring manually. Various modeling approaches have been applied so far, but it was difficult to accurately estimate light interception by conventional methods. The objective of this study is to estimate the spatial distributions of light interception and photosynthetic rate of paprika with time by using 3D-scanned plant models and optical simulation. Structural models of greenhouse paprika were constructed with a portable 3D scanner. To investigate the change in canopy light interception by surrounding plants, the 3D paprika models were arranged at $1{\times}1$ and $9{\times}9$ isotropic forms with a distance of 60 cm between plants. The light interception was obtained by optical simulation, and the photosynthetic rate was calculated by a rectangular hyperbola model. The spatial distributions of canopy light interception of the 3D paprika model showed different patterns with solar altitude at 9:00, 12:00, and 15:00. The total canopy light interception decreased with an increase of surrounding plants like an arrangement of $9{\times}9$, and the decreasing rate was lowest at 12:00. The canopy photosynthetic rate showed a similar tendency with the canopy light interception, but its decreasing rate was lower than that of the light interception due to the saturation of photosynthetic rate of upper leaves of the plants. In this study, by using the 3D-scanned plant model and optical simulation, it was possible to analyze the light interception and photosynthesis of plant canopy under various conditions, and it can be an effective way to estimate accurate light interception and photosynthesis of plants.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.49 no.1
• /
• pp.70-82
• /
• 2021

The purpose of this study is to reveal the tendency of planting design through the analysis of the planting of designer's gardens in the Suncheon Bay National Garden and to derive implications for future garden planting designs. The results of the study are as follows: First, the results of the study show that the practice of tree-based planting is still valid. Large growing trees such as 'Pinus densiflrora', 'Celtis sinensis', 'Zelkova serrata', 'Machilus thunbergii', 'Pinus strobus' overwhelmed the size of the designer's garden(150 to 390㎡). Second, the selection of trees tended to be made considering the designer's intention and the decorative effects rather than by considering the physiological and ecological conditions of the site. Third, among the herbaceous, the rate of the planting of perennials was high. Fourth, the flowering period of planted herbaceous was the most common in summer, followed by spring, fall, and winter. Fifth, the frequency color of the planted herbaceous was the most common in summer, followed by spring, fall, and winter. Fifth, in terms of flower color frequency, the most common was the yellow-series, followed by red-series, blue-series Sixth, average height herbaceous plants(20~60cm) were planted the most(47.4%). Seventh, structural plants that determined the garden's framework depended on trees, and the focal plants mainly utilized were evergreen trees, and the midrange plants were the planted herbaceous plants. The implications derived from the above findings are as follows: First, to ensure the garden's quality and sustainability, the selection of trees should be carefully considered, not considering only the artist's intention but also taking into account the physical and ecological conditions. Second, herbaceous plants can be used in various ways― the garden's focal plants, midrange plants, and ground covers, so more active herbaceous planting needs to be considered. Third, in consideration of the winter landscape, herbaceous planting using characteristics, such as fruits and stems, as well as flower colors should be considered. Fourth, blue and black color herbaceous plants have a noticeable effect even in a small amount, so it is necessary to plant them actively. Fifth, for the design of herbaceous planting, where the individual property of plants can be expressed, the design method should be considered.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.24 no.1
• /
• pp.13-34
• /
• 2022

Soil moisture data have been collected at 11 agrometeorological stations operated by The Korea Meteorological Administration (KMA). This study aimed to verify the accuracy of soil moisture data of KMA and develop a correction formula to be applied to improve their quality. The soil of the observation field was sampled to analyze its physical properties that affect soil water content. Soil texture was classified to be sandy loam and loamy sand at most sites. The bulk density of the soil samples was about 1.5 g/cm³ on average. The content of silt and clay was also closely related to bulk density and water holding capacity. The EnviroSCAN model, which was used as a reference sensor, was calibrated using the self-manufactured "reference soil moisture observation system". Comparison between the calibrated reference sensor and the field sensor of KMA was conducted at least three times at each of the 11 sites. Overall, the trend of fluctuations over time in the measured values of the two sensors appeared similar. Still, there were sites where the latter had relatively lower soil moisture values than the former. A linear correction formula was derived for each site and depth using the range and average of the observed data for the given period. This correction formula resulted in an improvement in agreement between sensor values at the Suwon site. In addition, the detailed approach was developed to estimate the correction value for the period in which a correction formula was not calculated. In summary, the correction of soil moisture data at a regular time interval, e.g., twice a year, would be recommended for all observation sites to improve the quality of soil moisture observation data.