• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.7
• /
• pp.741-748
• /
• 2013

A conventional packing ring was designed with a large clearance to prevent damage due to the vibration of the rotor, which can lead to an increase in steam leakage. In this study, a flexible packing ring using winding springs was developed to prevent damage to the rotor teeth by minimizing vibration, while maintaining a smaller clearance than that of conventional rotor designs. Theoretical analysis and finite element analysis (FEA) were used to design the winding spring to satisfy the specified allowable stress limit and minimum load requirements. The shape of the winding spring was designed by applying curves to the center and end parts of a flat spring. Computational fluid dynamics (CFD) analysis was used to predict the leakage of the flexible packing ring. Flow rate measurement tests were performed to verify the leakage reduction efficiency and the reliability of the CFD analysis.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.2
• /
• pp.1-8
• /
• 2015

Dual pulse rocket motor is a variant of solid rocket motor with two propellant grain separated by a pulse separation device. The major performance of such a rocket motor is influenced by the change in the hole area of pulse separation device to nozzle throat area ratio. In this study, we performed flow analysis to investigate the internal flow characteristics according to the pulse separation device hole area to nozzle throat area ratio change. Gases used flow analysis were used combustion gas of HTPB/AP composite propellant and nitrogen gas. Flow analysis results of the dual pulse rocket motor were validated by comparison with experimental results of pneumatics. Commercial CFD code ANSYS FLUENT 14.5 is used in this study to simulate flow analysis.

• 한국가시화정보학회:학술대회논문집
• /
• 2004.04a
• /
• pp.19-28
• /
• 2004

유동장의 특성을 구분할 수 있는 척도는 평균자유행로와 특성거리의 비인 누센수이다. 누센수에 따라서 유장은 연속체영역, 미끄럼영역, 천이영역, 및 자유분자영역으로 나누어진다. 고고도에서 비행체 주위의 유동장, 진공에서의 유동장 등이 비연속체영역 즉 저밀도유동장에 해당된다. 비연속체영역에 해당되는 또 다른 중요한 분야는 미세 유동장이다. 최근에 관심이 대두되고 있는 미세항공기(MAV)와 실리콘혁명 이래 유망한 미래기술중의 하나인 MEMS 장치 주위의 유동장 등이 바로 미세 유동장이다. 비연속체영역에서 유체의 이동 및 전달현상을 기술하기 위하여는 Boltzmann 방정식을 해석하여야한다. Navier-Stokes 방정식을 이용한 기존의 CFD 기법이 적용되지 않는 새로운 유동영역이기 때문이다. 본 발표에서는 Boltzmann 방정식의 유력한 해법인 직접모사(Direct Simulation Monte Carlo)법을 이용한 저밀도 유동장 해석이 소개될 것이다. 또한 직접모사법이 이용되기 어려운 다양한 저속 유동장에 대한 해석결과도 소개될 것이다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.4
• /
• pp.330-335
• /
• 2016

In this study, aerodynamic characteristics of the blades of a helical-type vertical axis wind turbine(VAWT) have been investigated. For this purpose, a 100-W helical-type vertical axis wind turbine was designed using a design formulae, and a 3D computational fluid dynamics analysis was performed considering wind tunnel test conditions. Through the results of the analysis, the aerodynamic power output and flow characteristics of a helical blade were confirmed. In order to validate the aerodynamic power output obtained through the analysis, a wind tunnel test was performed by using a full-scale helical-type vertical axis wind turbine. The 3D analysis technique was validated by comparing its results with those obtained from the wind tunnel test.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.75-75
• /
• 2011

본 논문에서는 진동중인 교량 거더에 작용하는 풍하중을 산정하고 그에 따른 플러터 발생풍속을 예측하기 위하여 분산형 전산환경을 활용한 수치해석 연구를 수행하였다. 분산형 전산환경은 웹 포탈을 기반으로 수치해석 환경을 제공하는 수치풍동 시스템으로서, 전산유체역학(CFD : Computational Fluid Dynamics)에 대한 전문지식이 부족한 사용자들도 격자생성, 수치해석자를 이용한 계산, 가시화 등의 전 과정을 편리하게 수행할 수 있는 차세대 토목분야 연구 환경이다. 본 시스템은 그리드스피어(GfidSphere)를 기반으로 구성되었으며, 기본적으로 사용자 관리, 세션 관리, 그룹 관리, 레이아웃 관리 등을 제공하여 사용자가 포탈을 통해서 다양한 서비스를 쉽게 사용할 수 있는 환경을 구축하도록 도와준다. 수치해석을 위한 유체 지배방정식은 2차원 비정상 비압축성 RANS(Reynolds-Averaged Navier-Stokes) 방정식이며, pseudo compressibility 방법을 적용하였다. 비정상 유동장을 해석하기 위하여 이중시간 전진법(dual time stepping)을 사용하였으며, 수렴가속화를 위해 Multi-grid 기법을 적용하였다. 또한 난류 유동장 해석을 위해서 $k-{\omega}$ SST 난류 모델을 사용하였으며, 난류 천이 과정에서의 유동을 모사하기 위하여 Total stress limitation 방법을 적용하였다. 교량 거더의 연직과 회전방향의 2자유도 움직임을 모사하기 위하여 동적격자 기법을 도입하였다. 교량 거더 주변의 비정상 유동해석 결과를 통해, 거더 표면에서 떨어져나가는 크고 작은 와류의 영향으로 양력 및 모멘트 계수 그래프가 중첩된 진폭과 주기를 갖고 주기적으로 나타나는 것을 확인할 수 있었다. 또한 계산된 비정상 공기력을 적용한 2자유도 플러터 방정식을 통하여 플러터 발생풍속을 산정하였다. 최종적으로 본 연구에서 계산된 결과의 타당성을 검증하기 위하여 수치적으로 구한 플러터 발생풍속과 기존의 실험 및 수치해석 결과를 비교하였으며, 결과는 잘 일치하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.7
• /
• pp.3164-3169
• /
• 2013

In this study, a series of CFD analysis was performed in order to predict the leaving water temperature and the slope of in-situ thermal response tests of the vertical-type geothermal heat exchangers. The geothermal heat exchanger and surrounding ground formation were modeled using GAMBIT and simulation was used by utilizing FLUENT which is commercial CFD code. Comparing with the results of CFD and in-situ thermal response tests, the results of CFD was presented good agreement with $0.5^{\circ}C$ difference of Leaving Water Temperature and with 1.6% difference of the Slope.

• 한국전산유체공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.81-85
• /
• 2005

Three-dimensional steady incompressible laminar entry flows in a square duct of $90^{\circ}$ bend are numerically simulated by a new solution code(PowerCFD) using unstructured cell-centered method. Solutions are obtained with three unstructured grid types of hexahedron, prism and hybrid at a Reynolds number, based on the hydraulic diameter and bulk velocity, of 790. Interesting features of the flow are presented in detail. Detailed comparisons between the computed solutions and the available experimental data are given mainly for the velocity distributions at cross-sections in a $90^{\circ}$ bend of a square duct with fully-developed entry flows. It is found that the code is capable of producing the nature of laminar flow in curved square duct with no grid type dependency.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.1
• /
• pp.70-77
• /
• 2008

A pre-processing program based on the OOP(object-oriented programming) concept has been developed. The program consists of the input of a 2D or 3D flow problem to a CFD program by means of an user-friendly interface and the subsequent transformation of this input into a form suitable for the solver(PowerCFD) using unstructured cell-centered method. User-friendly GUI(graphic user interface) has been built on the base of MFC(Microsoft Foundation Class). The program is organized as modules by classes based on VTK(Visualization ToolKit)-library, and these classes are made to function through inheritance and cooperation which is an important and valuable concept of object-oriented programming. The major functions of this program are introduced and demonstrated, which include mesh generation, boundary settings, solver settings, generation of grid connectivity and geometric data etc.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.242-243
• /
• 2010

The cooling system, including a fan is a one of the major sources to generate the radiated noise of construction equipment. Therefore, it is required to reduce the flow noise induced by a fan in order to reduce the noise level. In this study, we made an engine room model to carry out a variety of experiments. And then, the flow noise analysis technique using the CFD code was applied to the cooling system of construction equipment. These analyses results agree well with the measurement results. These results make it possible to understand the flow noise characteristics and to design the low noise cooling system in the design stage.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1000-1002
• /
• 2017

Here, the unsteady Navier-Stokes solver has been developed using implicit dual time stepping method. The implicit dual time stepping method introduced the pseudo time step for solving the new residual including the steady state residual and real time derivative. For the validation of code, Stokes 2nd problem, the laminar flow on the oscillating flat plate was selected and compare the calculating results with analytic solutions. The calculating velocity profile and skin friction has a good agreement with analytic solutions.