• 한국자동차공학회논문집
• /
• 제12권6호
• /
• pp.111-118
• /
• 2004

The work presented in this paper concerns the aerodynamic characteristics and compression wave generated in a tunnel when a high speed train enters it. A large number of solutions have been proposed to reduce the amplitude of the pressure gradient in tunnels and some of the most efficient solutions consist of (a) addition ofa blind hood, (b) addition of inclined part at the entrance, and (c) holes in the ceiling of the tunnel. These are numerically studied by using the three-dimensional unsteady compressible Euler equation solver with ALE, CFD code, based on FEM method. Computational results showed that the smaller inclined angle leads to the lower pressure gradient of compression wave front. This study indicated that the most efficient slant angle is in the range from $30^{\circ}$ to $50^{\circ}$. The maximum pressure gradient is reduced by $26.81\%$ for the inclined angle of $30^{\circ}$ as compared to vertical entry. Results also showed that maximum pressure gradient can be reduced by $15.94\%$ in blind hood entry as compared to $30^{\circ}$ inclined tunnel entry. Furthermore, the present analysis showed that inclined slant angle has little effect on aerodynamic drag. Comparison of the pressure gradient between the inclined tunnel hood and the vertical entry with air vent holes indicated that the optimum inclined tunnel hood is much more effective way in reducing pressure gradient and increasing the pressure rise time.

• 대한조선학회논문집
• /
• 제39권3호
• /
• pp.28-40
• /
• 2002

지면효과를 받는 2차원 날개 주위의 난류유동을 비압축성 RANS(Reynolds Averaged Navier Stokes) 방정식과 유한차분법(Finite Difference Method)을 이용하여 해석하였다. 높은 레이놀즈수에 효과적인 Baldwin-Lomax 난류모델을 사용하였다. 본 연구의 목적은 지면효과를 받는 2차원 날개단면에서의 각기 다른 두 바닥 경계조건(이동지면, 고정지면)에 따른 유동의 특성을 파악하는 것이다. Clark-Y(t/C 11.7%)날개단면의 계산 결과와 발표된 계산결과 및 실험 값과의 비교를 통해 본 수치해석 프로그램의 정확성을 검증하였다. NACA4412 날개단면에 대해 지면과의 높이변화에 대해서 두 바닥 경계조건에 대해서 유동해석을 수행하였다 계산결과에 의하면 이동지면과 고정지면에 대해서 양력과 모멘트는 별 차이가 없으나 항력은 고정지면의 경우가 이동지면의 경우보다 다소 작았다. 따라서 풍동시험에서 고정지면의 결과는 이동지면에 비해 상대적으로 저항이 낮게 평가될 가능성이 있다고 본다.

• 한국추진공학회지
• /
• 제9권1호
• /
• pp.53-60
• /
• 2005

소형위성 발사체 추진제 공급계 배관의 구부러짐으로 인하여 배관내부의 추진제 유동은 불균일하며 이는 터보펌프 전단의 블레이드의 파괴 및 후단의 가압된 추진제의 불안정성을 야기시킨다. 따라서 추진제의 효율적인 공급을 위하여 vane이 장착된 곡관 배관이 필요하며 내부에서의 유동장을 수치해석으로 규명하여 그 문제점을 해결할 수 있는 지 연구하였다. 따라서, 본 연구에서는 각각 90도와 45도로 구부러진 3인치 산화제 배관과 2.5인치 연료 배관의 구부러진 부분에는 $0\sim3$개의 vane을 등 간격으로 설치하였다. 3차원 Navier-Stokes 방정식을 풀기 위하여 상용코드를 이용하였으며, 곡관 배관 설계를 평가하기 위하여 각 90, 45도의 vane이 설치되지 않은 곡관과 $1\sim3$개의 vane이 장착된 곡관을 비교하였다. vane의 개수에 의한 배관 설계의 영향을 알아보기 위하여 90, 45도의 곡관에 vane이 0, 1, 2, 3개가 등 간격으로 장착이 되었을 때의 결과를 비교하였다. 배관내의 유동 균일성과 차압을 알기 위하여 속도크기와 압력분포를 계산하였다. vane이 많을수록 곡관의 각도가 클수록 곡관을 지난 유동은 더 균일해졌으나 배관 차압은 더 증가하였다.

• 대한토목학회논문집
• /
• 제38권5호
• /
• pp.627-634
• /
• 2018

본 연구에서는 바람의 영향을 받는 박스형 콘크리트 거더교에 대한 풍력계수를 산정하기 위하여 전산유체해석(CFD)를 수행하였다. 방음벽이 없는 교량 단면에 대한 항력계수, 양력계수 및 비틀림모멘트계수를 산정하였고, 이 풍력계수 값들을 다양한 높이의 방음벽을 갖는 교량 단면에 대한 풍력계수 값들과 비교하였다. 전산유체해석에서 풍력계수들을 산정할 때 전단응력수송(SST) $k-{\omega}$ 난류 모델을 적용하였고, 마찰 항력계수가 전체 항력계수에 미치는 기여도를 조사하였다. 연구 결과, 바람이 수평으로 불 때 항력계수는 방음벽의 높이가 커질수록 증가하였고, 마찰 항력의 기여도는 교량 단면에 방음벽이 없을 때 가장 높았다. 따라서 교량설계에서 풍력을 산정할 때 방음벽의 높이의 영향을 고려할 필요가 있으며, 벽면 마찰력은 교량에 작용하는 풍력을 산정할 때 중요한 역할을 하였다.

• 한국유체기계학회 논문집
• /
• 제13권1호
• /
• pp.42-51
• /
• 2010

Many different types of fan have been applying to various industrial fields. Fan design methods are much different depending on the types of fan, operating conditions, and connecting parts at the inlet or exit of the fan etc. In this study, design methods for an axial-type suction fan are studied. This fan discharges the air in the relative static pressure of -285Pa to the atmosphere with the flow rate of $960m^3/min$. For three-dimensional blade design, three different design methods were applied, such as the free vortex method, the exponential method, and the cascade method. In the cascade method, the blade loading along the radial direction was obtained from the lift coefficient which was necessary to obtain the pressure rise on a fan rotor. This method is different from the free vortex and the exponential method which control the strength of the vortex. The fan performance prediction was conducted using the CFD with three different inlet ducts. The best fan performance was obtained when the fan was designed by using the cascade method. The designed fan using the exponential method showed better performance compared to a fan designed using the free vortex method. However, the fan performance was changed depending on the installed inlet ducts. So, an efficient fan can be designed with the adjustment of design variables on the basis of the flow structures within the fan as well as the fan design procedure.

• 한국해양공학회지
• /
• 제29권6호
• /
• pp.418-426
• /
• 2015

Recently, shipping operators have been making efforts to reduce the fuel cost in various ways, such as trim optimization and bulb re-design. Furthermore, IMO restricts the hydro-dioxide emissions to the environment based on the EEDI (Energy Efficiency Design Index), EEOI (Energy Efficiency Operational Indicator), and SEEMP (Ship Energy Efficiency Management Plan). In particular, ship speed is one of the most important factors for calculating the EEDI, which is based on methods suggested by ITTC (International Towing Tank Conference) or ISO (International Standardization Organization). Many shipbuilding companies in Korea have carried out speed trials around the Korea Straits. However, the conditions for these speed trials have not been exactly the same as those for model tests. Therefore, a ship’s speed is corrected by measured environmental data such as the seawater temperature, density, wind, waves, swell, drift, and rudder angle to match the conditions of the model tests. In this study, fundamental research was performed to evaluate the ship resistance performance due to changes in the water temperature and salinity, comparing the ISO method and numerical simulation. A numerical simulation of a KCS (KRISO Container ship) with a free-surface was performed using the commercial software Star-CCM+ under three conditions that were assumed based on the water temperature and salinity data in the Korea Straits. In the simulation results, the resistance increased under low water temperature & high salinity conditions, and it decreased under high water temperature & low salinity conditions. In addition, the ISO method showed the same result as the simulation.

• 한국세라믹학회지
• /
• 제48권3호
• /
• pp.236-240
• /
• 2011

In order to deposit a homogeneous and uniform ${\beta}$-SiC films by chemical vapor deposition, we demonstrated the phase stability of ${\beta}$-SiC over graphite and silicon via computational thermodynamic calculation considering pressure, temperature and gas composition as variables. The ${\beta}$-SiC predominant region over other solid phases like carbon and silicon was changed gradually and consistently with temperature and pressure. Practically these maps provide necessary conditions for homogeneous ${\beta}$-SiC deposition of single phase. With the thermodynamic analyses, the CVD apparatus for uniform coating was modeled and simulated with computational fluid dynamics to obtain temperature and flow distribution in the CVD chamber. It gave an inspiration for the uniform temperature distribution and low local flow velocity over the deposition chamber. These calculation and model simulation could provide milestones for improving the thickness uniformity and phase homogeneity.

• 한국수소및신에너지학회논문집
• /
• 제25권1호
• /
• pp.97-104
• /
• 2014

In a coal gasifier for IGCC, hot syngas leaving the gasifier at about 1550oC is rapidly quenched by cold syngas recycled from the gas cleaning process. This study investigated the flow and heat transfer characteristics in the gas quench system of a commercial IGCC process plant under different operating pressures. As the operating pressure increased from 30 bar to 50 bar, the reduced gas velocity shortened the hot syngas core. The hot fly slag particles were retained within the core more effectively, and the heat transfer became more intensive around the hot gas core under higher pressures. Despite the high particle concentrations, the wall erosion by particle impaction was estimated not significant. However, large particles became more stagnant in the transfer duct due to the reduced gas velocity and drag force under higher pressures.

• 한국농촌건축학회논문집
• /
• 제19권4호
• /
• pp.49-56
• /
• 2017

Each country in the world currently concentrates on shifting into clean energy, which can be alternative energy, for global environment protection and solution to the problem of fossil fuel depletion. The Korean government is predicted to develop renewable energy, such as solar power, ground power, and offshore wind power, and to increase their supply ratios by ending the use of coals and nuclear power plants. This study conducted experiments on thermal storage performance of Trombe wall thermal storage materials using solar power and simulations in order to offer baseline data for the development of a hybrid air circulation system for heating that can maximize efficiency by simultaneously using solar and geothermal power. The study results are as follows: (1) In all the specimens with 3m, 5m, and 7m in the length of thermal storage pipe, $5.7^{\circ}C$, $7.8^{\circ}C$, and $10.5^{\circ}C$ rose, respectively, as the thermal storage effect of the specimens attaching insulation film and black tape to the general funnel. They were most excellent in terms of thermal storage effect. (2) As a result of thermal performance evaluation on the II type specimens, II-3 ($7.8^{\circ}C$ rise) > II-4 ($5.3^{\circ}C$ rise) > II-1 ($3.9^{\circ}C$ rise) > II-2 ($2.3^{\circ}C$ rise) was revealed, and thus II-3 (insulation film + black tape) was most effective as shown in the I type. (3) This study analyzed air current and temperature distribution inside of the greenhouse by linking actually measured values and simulation interpretation results through the interpretation of CFD (computational fluid dynamics). As a result, the parts absorbing heat and discharging heat around the thermal storage pipe could be visibly classified, and temperature distribution inside of the greenhouse around the thermal storage pipe could be figured out.

• 한국가스학회지
• /
• 제18권4호
• /
• pp.56-62
• /
• 2014

본 연구에서는 촉매가 들어있는 고정층 반응로의 단일 개질관에 대하여 전산 유체 해석(Fluent ver. 13.0)을 수행하여 열/유동 특성을 파악하고, 주입 가스에 따른 추출 가스의 종류를 다공성에 따라 예측하였다. 촉매 형상을 모델링하기 위하여, 개질관 내부에 있는 촉매를 모두 다공성 물질이라고 가정하고, 수정된 Eugun 식을 해석에 적용하였다. 유체의 공극률을 기준으로 0.545, 0.409, 그리고 0.403로 설정하고, 결과를 비 다공성인 경우와 비교하였다. 수치해석 결과, 개질관 벽면의 온도는 흡열반응과 주변 열전달로 인하여 개질관의 온도보다 높게 나타나며, 수소 생성량도 다소 증가했다. 촉매의 공극률이 증가 하게 될 경우, 압력 강하로 인하여 관 중심부 온도 및 수소 생성량이 현저하게 감소하는 경향을 보였다.