• Journal of the Korean Wood Science and Technology
• /
• v.33 no.3 s.131
• /
• pp.53-63
• /
• 2005

This study attempted to obtain the basic data of utilizable possibility of preservative treated wood as a material used in a marine ranch. To evaluate the leaching stability of CCA-, CCFZ-, and ACQ-treated woods in seawater, the specimens treated with 2% and 3% (w/v) of CCA, CCFZ, and ACQ were exposed to deionized water, synthetic seawater and natural seawater for 41 days and then each component released was periodically determined. There was little amount of copper and chromium released from CCA-treated wood exposed in both deionized and seawater. Although relatively large amount of arsenic was released from CCA-treated wood, the release rate in seawater was lower than that in deionized water. The release rate of chromium and zinc from CCFZ-treated wood were somewhat greater in deionized water, but lower in seawater than in deionized water. Retention level and salinity of synthetic seawater had little effect on the release rate of components. The ACQ-treated wood had greater copper release than CCA- and CCFZ-treated wood, and the amount of copper released did not affected by leaching media used.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.1
• /
• pp.52-59
• /
• 2001

The fixation characteristics of CCA and CCFZ in Japanese red pine, Japanese larch, and ezo spruce sapwood were compared at various temperatures and fixation conditions (drying and nondrying fixation). Fixation was monitored by the rates of reduction of hexavalent chromium to trivalent one, and optimal fixation time was estimated based on the results. The rate of fixation was highly temperature dependent, and the fixation rate of treated wood conditioned under nondrying conditions was much more faster than that under drying conditions, especially when the moisture content of treated wood was below fiber saturation point. Preservative types affected fixation; CCA-Type B had the highest fixation rate, followed by CCA-Type C and then CCFZ. The differences in fixation rates of preservative components were also observed among wood species; Japanese red pine fixed the fastest, followed by Japanese larch and then ezo spruce. Time required to complete fixation according to the fixation temperature could be predicted successfully using the regression equations between the temperatures and fixation time, regardless of conditioning methods, preservative types, and wood species.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.2
• /
• pp.151-157
• /
• 2002

The removing copper from CCA, CCFZ treated wood were tested with Tyromyces palustris. The shacking culture, solid culture, and stationary culture methods were tested to removal of copper in CCA, CCFZ treated wood. The steam pressure method and oxalic acid method were tested as pretreatment. To investigate of copper removal mechanism, the oxalic acid that produced by T. palustris and combination with copper was examined on stationary culture that contained CCA and CCFZ treated wood chips. Oxalic acid increased copper removing rate of T. palustris as pretreatment. Stationary culture had most removal effectiveness among the culturing methods. The removal rate of copper on bioreactor was 61% on 7 days. Copper-oxalate was detected on liquid culture, which show the oxalate from liquid of culture combined with copper from treated wood. It would be related to the removal of copper from treated wood by T. palustris.

• Journal of the Korean Wood Science and Technology
• /
• v.23 no.3
• /
• pp.66-72
• /
• 1995

The rate of fixation of the components were evaluated in CCA-Type B and CCFZ-treated radiata pine sapwood by quantitative analysis of solution expressed from the treated wood. The leaching characteristics of radiata pine blocks treated with CCA-Type B and CCFZ were also evaluated by the AWPA standard leaching test. Both fixation and leaching charactersistics of CCA-Type B were compared with CCA-Type C treated wood samples. The rate of CCA-Type B fixation was a little faster than that of CCFZ. However, significant amounts of arsenic was unfixed in the CCA-Type B treated samples and consequently leached. These significant quantities of arsenic liberated from the CCA-Type B treated wood during service may pose some environmental concerns. Arsenic was no longer detectable from CCA-Type C treated samples when fixation was complete, even though the fixation of CCA-Type C was slower in some degree than CCA-Type B. In summary, it could be said that CCFZ was much safer preservative than CCA-Type B by the criterion based on the relative hazard assessed by absolute amount of unfixed element present in the treated wood. Also the decision that CCA preservative has to move from Type B to Type C should be made sooner or later for continuous use of CCA preservative in the future.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.6
• /
• pp.55-59
• /
• 2003

The fixation and leaching characteristics of chromated copper arsenate (CCA Type C) and chromium- copper-fluoride-zinc (CCFZ) in domestic softwood (Japanese red pine, Korean pine, and Japanese larch) sapwood were investigated using the expressate method to follow chromium fixation and the American Wood-Preservers' Association (AWPA) leaching procedure to determine leaching properties after fixation. The rates of fixation were affected by preservative types; CCA was fixed much faster than CCFZ for all species evaluated. There were definite differences in the fixation rates of different species, with Korean pine requiring shorter to fix than the other species evaluated. Chromium fixation was greatly enhanced by elevated temperatures, and fixation time can be estimated according to fixation temperatures applied. The percentage of arsenic and zinc leached from domestic softwoods was relatively high compared to chromium and copper, indicating that there is still a relatively high unfixed arsenic and zinc components after complete chromium fixation in CCA-and CCFZ-treated samples, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.4
• /
• pp.93-99
• /
• 1996

In order to investigate the extent of fixation of new water-borne preservatives in blocks of pinus densiflora sapwoods the streaming potential through the column with preservative treated wood was measured at various conditions. The rates of leachability of ingredients in the treated wood were estimated by the measurement of electric conductivity of the solution with the leached components. The solution was also analyzed by Atomic absorption spectrophotometer (AA). As a results, the experimental data indicated that the fixation of CCB, CCFZ and ACQ in wood were relatively unstable. The fixation rates of CCB, CCFZ were improved by increasing heat and drying time. The amounts of the leached ingredients were apparently higher in CCB and CCFZ than in CCA, while the rate of leaching of ACQ was not changed at various drying temperature.

• Journal of the Korean Wood Science and Technology
• /
• v.23 no.4
• /
• pp.60-66
• /
• 1995

The treatability of Japanese larch heartwood was assessed by pressure treatment of non-incised dimension material with CCA or CCFZ. The effectiveness of incising(conventional, high density, and needle incising) for improving CCA treatability on refractory Japanese larch heartwood was also investigated. Preservative retention and penetration were somewhat greater with CCFZ treatment, although those was generally poor in both preservatives. The retention gradients for both CCA and CCFZ-treated stock were essentially the same shape. Treatment of non-incised material with CCA acheived the recommended treatability for using treated wood at the regions of hazard class H2 in the Japanese Agricultural Standards. However, Japanese larch heartwood would require incising as a pretreatment for enhancing treatability, if CCA-treated larch is intended to be used at the regions of hazard class H3 and H4. As expected, incising resulted in a considerable improvement of preservative treatability, particularly penetration, and the effect of incising on the improvement of treatability was excellent at the sequence of needle incising, high density incising, and conventional incising. Among incising techniques investigated in this study, high density and needle incising enhanced CCA treatability beyond the point where it did meet a minimum requirements specified by the Japanese Agricultural Standards for using CCA-treated Japanese larch at the regions of hazard class H3 and even H4.

• Journal of the Korean Wood Science and Technology
• /
• v.23 no.4
• /
• pp.33-38
• /
• 1995

The rates of fixation of CCA-Type B and CCFZ in blocks of radiata pine sapwood were compared at various temperatures and conditioning methods (drying and nondrying conditioning). Also the time required to proper fixation of preservative components in the treated wood was estimated. Fixation was monitored by the rates of depletion of free hexavalent chromium in the cell lumens in the teated blocks. The rate of preservative fixation in wood was highly temperature dependent. The fixation rate was considerably accelerated by means of heating and complete fixation of hexavalent chromium was achieved within about 12 hours by heating at $60^{\circ}C$. The moisture content of treated wood during fixation apparently played an important role in the fixation process. The fixation rate of treated wood conditioned in nondrying conditions was much more faster than that of treated wood conditioned in drying conditions. particularly when the moisture content of treated wood was below fiber saturation point. Time required to full fixation could be predicted successfully using the fixation temperatures applied since the correlation between the fixation temperature and the fixation time was excellent. regardless of conditioning methods.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.2
• /
• pp.1-8
• /
• 2004

Heavy metals were removed from CCA- and CCFZ- treated wood using a brown-rot fungi Tyromyces palustris. The amount of effective elements extracted from treated woods was compared for different treatment methods. The relationship between the amount of heavy metals removed and concentrations of oxalic acid for treated wood was examined. Also, the relationship between mycelia weight and removal rate was examined. The removed quantity of heavy metal from treated wood according to fermentation methods was examined. The extraction amount of chromium and arsenic components increased with increasing oxalic acid concentration, but the extraction amount of copper did not improved much. A 287 mg of mycelia weight can remove chromium and arsenic over 60% in 3 g CCA chips and copper was also removed over 50%. The chromium, copper and arsenic were removed over 60% by shaking fermentation, the removal rate of copper by static cultivation was higher than that of shaking fermentation. The removal rate of chromium, copper and arsenic were 72%, 61% and 59% with air-lift bioreactor, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.28 no.4
• /
• pp.61-71
• /
• 2000

The effect of the treatment with CCFZ, FR-4, and PEG400 from butt end on the dimensional stability and bending properties was examined. Three softwood species such as red pine, Korean white pine and Japanese larch and three hardwood species such as poplar, alder and oak were investigated in this research. Shrinkage of red pine, Korean white pine, poplar, and alder treated with PEG400 decreased. However, there was no significant decrease of shrinkage in Japanese larch and oak. The decrease of shrinkage when moisture content changed from about 20% to 10% was larger than that at any other phase. In regard to the effect of treatment on bending properties, bending MOE and MOR of all specimens treated with PEG400 decreased significantly. Especially in the case of red pine, poplar, and alder treated with PEG400, bending MOR reduced 9%, 14%, and 12%, respectively. Reductions of MOR of the hardwood was also much larger than that of the softwood. However, in all species, treatment with CCFZ and FR-4 did not affect the change of bending MOE and MOR significantly. Comparing the large specimen which also included heartwood with the small specimen which included only treated sapwood, there was a difference in the change of bending MOE and MOR between them. The large specimens of Korean white pine, alder and Poplar, which had a relatively low proportion of sapwood(18~22%), showed the decrease of MOR by 11~13% more than that of small specimens, while red pine, Japanese larch and oak, which had a relatively high proportion of sapwood(35~40%), showed little decrease. It means that bending MOE and MOR of structural wood treated from butt end should be considered in terms of sapwood proportion as well as effect of treated chemicals.