Purpose: Waste parts of zirconia blocks and powders were remained after CAD/CAM process. In order to make these residual zirconia fit for practical use, zirconia single cores were produced by drain casting process. Methods: Remained zirconia blocks were reduced to powders with zirconia mortar, and screened with 180 mesh sieve. Zirconia slip was prepared from waste parts of zirconia by ball milling. Plaster molds for forming cores by slip casting were also prepared. Formed cores were removed from mold after partial drying. Dried cores were biscuit fired at $1,100^{\circ}C$ for 1hour. Biscuit fired cores were treated with tools to control the fitness and thickness. Finished cores were $2^{nd}$ fired at $1,500^{\circ}C$ for 1hour. Microstructure of cross section of core was observed by SEM. Results: When mill pot was filled with 100g of zirconia and alumina mixed powder, 300g of zirconia ball, and 180g of distilled water, the optimum slip for drain casting was obtained. Gypsum plaster for ceramic forming was more suitable then yellow stone plaster for casting process. SEM photograph showed the microstructure of fully dense with uniform grain size of zirconia and well dispersed alumina grains into the zirconia matrix. Conclusion: Zirconia single cores were produced by drain casting process. Drain casting is useful process to make these residual zirconia fit for practical use. Further study will be focused on the preparation of the bridge type cores by casting.
This study was to investigate the anatomical evidence of anxiety. MRI was used to study 11 patients with panic disorder and 15 patients with complex partial seizure, and 21 controls. The regions of interest in the MRI were measured with computer-assisted planimetry using the AutoCad and digitizer. The following results were obtained ; 1) The mean age was 49.7(12.4) years in patients with panic disorder and 30.1(7.5) years in patients with complex partial seizure. 2) There were na signi ficant differences between 3 groups in the values of cerebral area, temporal lobe, caudate nucleus, hippocampus, parahippocampus, amygdala, third ventricle and VBR. The right parahippocampal region which attracted most attention in neurobiological studies regarding anxiety, tended to be larger in both study groups compared to the control group, but with no statistical significance. 3) There was lett-right reversal of temporal lobes in both study groups. And these are mainly due to asymmetrical increase in area of the temporal lobe on right side. These results suggest that temporal lobe, especially right temporal, is the anatomical correspondence of anxiety and functional activation of temporo-limbic system may be accompanied by the structural change of temporal lobe.
본 연구에서는 하나의 주제에 대한 교육 충실도를 높이기 위해 해석적인 수식전개에 바탕을 둔 이론 강의, 상용 소프트웨어를 이용한 수치 시뮬레이션, 그리고 계산 결과를 기초로 얻어진 설계 모델들에 대하여 제작과 실험을 통해 얻어진 결과를 수치계산 결과와 비교 검토의 세가지 접근 방법을 병행할 수 있는 장소를 일컫는 studio class를 활용한 교육방법에 대하여 전자공학교육 분야의 사례연구를 통해 설명하고자 한다. 초고주파 수동소자의 하나인 저역통과여파기에 대해 studio class 개념의 교육과정을 학부생 및 대학원생에게 적용한 결과를 하나의 사례로 들어 국내의 교육환경에 적합한 studio class 교수법에 대한 효과와 학생들의 전문지식 습득에 대한 이해도의 효율성에 대하여 고찰하고자 한다.
Chitosan is a polysaccharide with cationic amino groups in its structure and has useful properties as functional materials. Various end-use developments of chitosan are in progress. When the cotton fabric is pretreated with chitosan, the hand property of cotton fabric may be improved expecially for the summer apparel. In this study, as a cross-linking agent to introduce chitosan into cotton, BTCA(butane-1,2,3,4-tetracarboxylic acid) or CA(citric acid) was added in order to prevent detachment of chitosan by the cross-linking. During the cross-linking procedure, via the padding-drying-heat setting, amino groups of chitosan and hydroxyl groups of cotton, carboxyl groups of BTCA/CA are cross-linked by forming anhydrous cyclic rings. Since BTCA has four carboxyl groups, cross-linking by thermal treatment is easy, leading to the trials in wrinkle-recovery treatment of cotton fabrics. However, the high price of the BTCA reagent has been a shortcoming in the actual application for industrial use. Therefore, in this study, we tried the application of CA having three carboxyl groups, which is relatively low priced, as the substituting cross-linking agent. The hand of the treated fabrics were evaluated by measuring physical properties. In addition, based on the physical properties, three-dimensional images were introduced by using 3D CAD systems and results were compared.
Giardia lamblia, an anaerobic, amitochondriate protozoan parasite causes parasitic infection giardiasis in children and young adults. It produces pyruvate, a major metabolic product for its fermentative metabolism. The current study was undertaken to explore the effects of pyruvate as a physiological antioxidant during oxidative stress in Giardia by cysteine-ascorbate deprivation and further investigation upon the hypothesis that oxidative stress due to metabolism was the reason behind the cytotoxicity. We have estimated intracellular reactive oxygen species generation due to cysteine-ascorbate deprivation in Giardia. In the present study, we have examined the effects of extracellular addition of pyruvate, during oxidative stress generated from cysteine-ascorbate deprivation in culture media on DNA damage in Giardia. The intracellular pyruvate concentrations at several time points were measured in the trophozoites during stress. Trophozoites viability under cysteine-ascorbate deprived (CAD) medium in presence and absence of extracellular pyruvate has also been measured. The exogenous addition of a physiologically relevant concentration of pyruvate to trophozoites suspension was shown to attenuate the rate of ROS generation. We have demonstrated that Giardia protects itself from destructive consequences of ROS by maintaining the intracellular pyruvate concentration. Pyruvate recovers Giardia trophozoites from oxidative stress by decreasing the number of DNA breaks that might favor DNA repair.
A seamless analysis of complex geometry is one of greatly interesting topic. However, there are still gaps between the industrial applications and fundamental academic studies owing to time consuming modeling process. To resolve this problem, an auto mesh generation program based on grid-based approach has been developed for IT-product in the present study. At first, base mesh and skin mesh are generated using the information of entities which extracted from IGES file. Secondly the provisional core mesh with rugged boundary geometry is constructed by superimposing the skin mesh as well as the base mesh generated from the CAD model. Finally, the positions of boundary nodes are adjusted to make a qualified mesh by adapting node modification and smoothing techniques. Also, for the sake of verification of mesh quality, the hexahedral auto mesh constructed by the program is compared with the corresponding tetrahedral free mesh and hexahedral mapped mesh through static finite element analyses. Thereby, it is anticipated that the grid-based approach can be used as a promising pre-processor for integrity evaluation of various IT-products.
A novel rapid prototyping (RP) process, a full-automated transfer type variable lamination manufacturing process (Full-automated VLM-ST) has been developed. In the full-automated VLM-ST process, a vacuum chuck and a rectilinear motion system transfer the EPS foam material in the form of the plate with two pilot holes to the rotary supporting stage. The supplied material is then cut into an automated unit shape layer (AUSL) with a desired width, a desired length, a desired slope on the side surface, and a pair of reference shapes, which is called the guide shape (GS)’, including two pilot holes in accordance with CAD data through cutting in two steps using a four-axis synchronized hotwire cutter. Then, each AUSL is stacked by setting each AUSL with two pilot holes in the building plate with two pilot pins, and subsequently, adhesive is applied onto the top surface of the stacked AUSL by a bonding roller and pressure is simultaneously given to the bottom surface of the stacked AUSL. Finally, three-dimensional shapes are rapidly and automatically fabricated. This paper describes the method to generate guide shapes in AUSL data for the full-automated VLM-ST process. In order to examine the applicability of the method to generate guide shapes, three-dimensional shapes, such as a piston shape and a human head shape, are fabricated from the full-automated VLM-ST apparatus.
사이클로이드 감속기는 기계의 회전수를 조절하기위한 장치이다. 사이클로이드 감속기는 큰 토크로 변환시킬 수 있는 장점이 있지만 높은 회전수 에는 적합하지 않다. 한편 200톤 하중이 가해지는 수송기기에 있어서 감속기의 사용한계속도를 찾아내기는 불가능하다. 본 연구에서는 LS-DYNA를 이용하여 마찰손실동력을 수치 해석적으로 검토하였다. 최대토크3.5ton-m에 있어서 회전수 60rpm 그리고 162rpm으로 구동하여 해석을 수행한 결과 다음과 같은 결과를 얻었다. 60rpm회전의 경우 최대응력은 RV gear의 경우 463MPa 핀기어의 경우 507MPa이 발생하였다. 마찰손실동력은 50kW이며, 162rpm의 경우 최대응력값은 RV gear와 핀기어 각각 550MPa, 538MPa이 발생하였다. 손실동력은 175kW이 발생하여 사용이 불가능하다는 것을 알 수 있었다.
산업환기의 근본 목적은 유해물질로부터 작업자의 건강을 지키는 것으로, 제품생산과정에서 발생하는 유해물질 등을 빠른 시간에 외부로 배출하여 공기의 질을 높이고자 한다. 최근 산업환기에 대한 인식이 생산중심에서 인간중심으로 변하면서 이에 대한 중요성이 증가하고 있다. 본 연구에서는 아연말 코팅 룸에서 발생하는 악취제거를 목적으로 코팅 룸 내부의 공기유동에 대한 전산 시뮬레이션을 수행하였다. 3차원 CAD 프로그램인 SolidWorks를 이용하여 코팅 룸 전체와 배기시스템을 모델링하였으며 Flow Simulation 프로그램을 이용하여 오염물 발생 부위 중심으로 배기성능을 분석하였다. 또한 국소배기 장치를 이용하여 코팅 룸 내부 공기의 흐름 방향과 공기의 유속을 개선하였다.
소비자의 기호가 다양화되면서 다품종 소량생산에 따른 대량 맞춤화에 대한 관심이 높아지고 있으며, 1990년대 후반부터 급격히 확산되고 있는 인터넷의 발달 및 디지털 기기의 확산에 따라 인터넷을 기반으로 한 전자상거래 환경에서의 대량 맞춤화 프로세스는 최근 의류 분야에서 주요한 경향으로 받아들여지고 있다. 대량 맞춤화 의류 제품의 수요는 인터넷 등 IT 기술의 발달과 맞물려 최근 개인의 특성과 취향을 고려한 인터넷 맞춤서비스를 기반으로 증가추세에 있으며, CAD 등의 테크놀러지의 활용을 통하여 디자인, 패턴제작, 재단 등의 자동 시스템을 도입함으로써 그 영역을 확장하고 있다. 이에 발맞추어 국내에서는 '디지털 패션 시스템'을 통해 3차원 바디 스캔, 3차원 컴퓨터 그래픽스, 3차원 Simulation, DID, DTP, 맞춤주문형 제품의 대량 생산기술 등의 단위 기술이 기업단위로 활용되는 등 가상현실을 이용한 3차원 가상쇼핑 등을 포함하는 기술로서 차세대 섬유패션 산업의 창출에 기여하고 있다. 그 중, 디지털 텍스타일 프린팅은 디자인에서부터 날염까지 전체 공정을 컴퓨터로 처리하여 기존의 복잡한 날염 공정을 단축하여 다품종 소량생산이 가능한 날염 방식으로, 대량 맞춤형 프로세스를 지원하며, 프로슈머(prosumer)로서의 소비자가 직접 참여하여 그들의 욕구를 최대화 할 수 있는 소비자 만족을 극대화 시킬 수 있는 대량 맞춤화 프로세스 중 하나의 단계로 소비자의 수요 반영하는 요소로 작용하고 있다. 즉, 디지털 패션 시스템에서의 디지털 텍스타일 프린팅은 대량 맞춤형 의류 제품에 있어 소비자 만족도와 직결되는 요인으로 분석된다. 따라서, 본 연구에서는 디지털 패션 시스템 기반의 대량맞춤형 섬유제품 및 디지털 텍스타일 프린팅 적용 섬유제품에 대한 기초 평가 문항을 제시하고, 소비자 태도를 분석하여 제시하였다. 또한, 분석된 기초 소비자 태도를 반영하여, 디지털 패션 시스템 기반의 디지털 텍스타일 프린팅(Digital Textile Printing) 의류 제품의 선호도, 인지도, 수요도 및 구입의향을 분석하여 최종적으로 디지털 패션 시스템에 적용된 디지털 텍스타일 프린팅 의류 제품의 수요 경향을 제시하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.