• Journal of Astronomy and Space Sciences
• /
• v.36 no.1
• /
• pp.11-20
• /
• 2019

Being a torque free motion of the rotating Earth, Chandler wobble is the major component in the Earth's polar motion with amplitude about 0.05-0.2 arcsec and period about 430-435 days. Free core nutation, also called nearly diurnal free wobble, exists due to the elliptical core-mantle boundary in the Earth and takes almost the whole part of un-modelled variation of the Earth's pole in the celestial sphere beside precession and nutation. We hereby present a brief summary of their theories and report their recent features acquired from updated datasets (EOP C04 and ECMWF) by using Fourier transform, modelling, and wavelet analysis. Our new findings include (1) period-instability of free core nutation between 420 and 450 days as well as its large amplitude-variation, (2) re-determined Chandler period and its quality factor, (3) fast decrease in Chandler amplitude after 2010.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.10 no.1
• /
• pp.50-63
• /
• 2002

The Karman boundary-layer has been numerically investigated for the disturbance wave number, wave velocity, azimuth angle and radius (Reynolds number, Re). The disturbed flow over rotating disk can lead to transition at a much lower Re than that of the well-known Type I instability. This early transition is due to the excitation of the Type II. Presented are the neutral stability results concerning these instabilities by solving newly formulated stability equations with consideration of whole convective terms. When the present numerical results are compared with the previously known results, the value of critical Re corresponding to Type I is moved from ${Re}_{c.1}$=285.3 to 270.2 and the value corresponding to Type II from ${Re}_{c.2}$=69.4 to 36.9, respectively. Also, the corresponding wave number is moved fro)m $k_1$=0.378 to 0.386 for Type I; from $k_2$=0.279 to 0.385 for Type II. For Type II, the upped limit of wave number and azimuth angle is $k_u$=0.5872, $\varepsilon_u$=$-17.5^{\circ}$, while its lower limit is near $k_u$=0, $\varepsilon_u$=$-28.4^{\circ}$. This implies that the disturbances will be relatively fast amplified at small Re and within narrow bands of wave number compared with the previous results.

• Journal of Korean Ophthalmic Optics Society
• /
• v.4 no.2
• /
• pp.105-111
• /
• 1999

This paper presents experimental results on the electrical properties of hydrogenated amorphous carbon films(a-C:H) prepared by PECVD. DC conductance of a-C:H was measured as a function of temperatures in the range of 100 to 423K. We studied two a-C:H films: one was well explained by the Mott's Variable Range Hopping(VRH) rule, but the other sample did not follow it. However, the conduction data of second sample were well fitted to Shimakawa's Multi-Phonon Hopping(MPH) model according to which conductivity is proportional to $T^M$ with m=15-17. but, in our samples, m was 10-12. Also a-C:H showed several bias effects like relaxation of conductance, bias-dependent conductance and the change of conductance slope in 1n(${\sigma}{\sqrt{T}}$) vs. $T^{1/4}$ plot. In this study we interpret these data by bias-dependent detrapping model.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.35 no.12
• /
• pp.1477-1485
• /
• 2011

Dyeability and colorfastness of the blended knits of cotton/rayon (40/60; C/R) and wool/tencel (10/90; W/T) are examined using the natural dyestuff ($Pinux^{TM}$) manufactured from Pinus radiata pine bark extract. In addition, pre-treatments (such as bleaching, mercerization and cationization) are performed to improve dyeability and colorfastness. The $Pinux^{TM}$ powder dyestuffs produced by Pinux Co., Ltd. are used as dyestuffs and their properties are examined for dyeing concentration (0.5-2% (owb)), dyeing time (30-120 minutes) and dyeing temperature (30-$90^{\circ}C$). Dyeability is evaluated with K/S value at 400nm, which is the maximum absorption wavelength for $Pinux^{TM}$. The results show the dyeability of W/T sample containing protein fiber with $Pinux^{TM}$ is superior to all cellulose fiber C/R. A concentration of dyestuff greater than 1.5% (owb), dyeing time 120 minutes and dyeing temperature of $90^{\circ}C$ are the most optimized conditions. It shows that the dyeability of C/R and W/T samples are high in the condition of an acid-dyeing bath and that dyeability highly declined in alkaline bath due to the instability of the proanthocyanidin pigment. After analyzing the effect of bleaching, mercerizing and cationizing (as pre-treatments on dyeability) it was concluded that the dyeability of the C/R sample was enhanced by mercerization but no significant effect by cationization. However, the simultaneous treatment of cationizing and dyeing resulted in far improved dyeability compared to dyeing after cationizing pre-treatment. As for the W/T sample, the effect of cationization was more prominent than the C/R sample. Colorfastness to color changes in the control W/T sample was higher than that of C/R's level 1-2, and it increased to Level 2 when bleaching pre-treatment was given and when a simultaneous cationizing treatment was adopted to the dyeing process. Colorfastness to light in W/T control sample resulted in Level 3 and further increased to an excellent Level of 4 with bleaching and simultaneous cationizing during dyeing process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1988.05a
• /
• pp.78-81
• /
• 1988

Nitroxide films were made from the $NH_3$ gas nitridation of as-grown $SiO_2$. The electrical characterization results including C-V characteristics and BT stress generally indicate that the high field stress instability and insulator-substrate interfacial characteristics are improved by nitridation of $SiO_2$. A C-V technique was used to determine the surface state density $N_{55}$ and then $N_{55}$ in the nitroxide-substrate interface was $8{\times}10(/eVcm^2$). This $N_{55}$ is related with 1/f noise was revealed experimentally and relationship was plotted and 1/f noise characteristics were also improved by nitridation of of $SiO_2$By the results of measurements on these films show that very thin thermal silicon nitroxide films can be used as gate dielectrics for future highly scaled-down VLSI device.

• Journal of KSNVE
• /
• v.10 no.6
• /
• pp.991-997
• /
• 2000

The objective of this study is to examine the onset condition and the frequency characteristics of the low-frequency combustion oscillation in a surface burner. For this purpose, extensive parametric studies have been performed experimentally and the effects of size of each section, the equivalence ratio, and the entrance velocity on oscillatory behavior explored. The experimental results were discussed in comparison with the other combustors associated tilth the low-frequency combustion oscillation. The combustion mode is driven at high combustion rate by the lift of unstable flame near the lower limit of the combustible equivalence ratio. The oscillation frequency is dependent not on the burner geometry but on the equivalence ratio and the combustion load. Low-frequency combustion mode was formed to be divided into two different modes, named C1 and C2 respectively. Two modes occurred individually, simultaneously or transitionally according to the equivalence ratio and combustion load. The characteristics of low-frequency oscillation is different from each other depending on the type of combustors. The surface burner has also its own characteristics of low -frequency oscillation.

• Journal of the Korean Applied Science and Technology
• /
• v.7 no.1
• /
• pp.71-76
• /
• 1990

Transesterification reactions (methyl methacrylate with monoethanolamine, methyl methacrylate with n-butyl alcohol, dimethylphthalate with ethylene glycol, dimethyl phthalate with monoethanolamine) were kinetically investigated in the presense of various metal acetate catalysts at $110^{\circ}C$. The amount of reactants was measured by gas and liquid chromatography, and the reaction rates also measured from the amount of reaction products and reactants upon each catalyst. The transesterification reactions were carried out under the first order conditions respect to the concentration of reactants, respectively. The overall reaction order was 2nd, Maximum reaction rates were appeared at the range of 1.4 to 1.6 in electronegativity of metal ions and maximum catalytic activities were obserbed at the range of 1.5 to 1,8 in instability constant of metal acetates.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.9 no.4
• /
• pp.141-146
• /
• 2010

In this paper, bandgap reference PTAT(Proportional to Absolute Temperature) circuit and flexible gain control of LNA(Low Noise Amplifier) which is usable in Zigbee system of 2.4GHz band are designed by TSMC $0.18{\mu}m$ CMOS library. PTAT bandgap reference circuit is proposed to minimize the instability of CMOS circuit which may be unstable in temperature changes. This circuit is designed such that output voltage remains within 1.3V even when the temperature varies from $-40^{\circ}C$ to $-50^{\circ}C$ when applied to the gate bias voltage of LNA. In addition, the LNA is designed to be operated on 2.4GHz which is applicable to Zigbee system and able to select gains by changing output impedance using 4 NMOS operated switches. The simulation result shows that achieved gain is 14.3~17.6dB and NF (Noise Figure) 1.008~1.032dB.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.1
• /
• pp.55-60
• /
• 2002

For the development of a new creep test technique, the availability of SP-Creep test is discussed for 1Cr-0.5Mo boiler header material. And some results are also compared with those of 2.25Cr- 1Mo steel which widely uses as boiler superheater tube. The results can be summarized as follows. The load exponents(n) obtained by SP-Creep test for 1Cr-0.5Mo steel are decreased with increasing creep temperature and the values are 15.67, 13.89, and 17.13 at 550$^{circ}C$ ,575$^{circ}C$ and 600$^{circ}C$, respectively. The temperature dependence of the load exponent is given by n = 107.19 - 0.1108T. This reason that load exponents show the extensive range of 10∼16 is attributed to the fine carbide such as M$_{23}$C$_{6}$ in lath tempered martensitic structures. At the same creep condition, the secondary creep rate of 1Cr-0.5Mo steel is lower than the 2.25Cr-1Mo steel1 due to the strengthening microstructure composed by normalizing and tempering treatments. Through a SEM observation, it can be summarized that the primary, secondary, and tertiary creep regions of SP-Creep specimen are corresponding to plastic bending, plastic membrane stretching, and plastic instability regions among the deformation behavior of four steps in SP test, respectively.y.

• Journal of the Korean Applied Science and Technology
• /
• v.4 no.1
• /
• pp.67-71
• /
• 1987

The transesterification reaction between diethanolamine and methyl methacrylate was kinetically investigated in the presence of various metal acetate catalysts at $120^{\circ}C$. The amount of reacted methyl methacrylate was measured by gas chromatography and liquid chromatography, and the reaction rate also measured from the amount of reaction products and reactants under each catalyst. The transesterification reaction was carried out in the first order with respect to the concentration of diethanolamine and methyl methacrylate, respectively. The over-all order is 2nd. The apparent rate constant was found to obey first-order kinetics with respect to the concentration of catalyst. The maximum reaction rate was appeared at the range of 1.4 to 1.6 of electronegativity of metal ions and instability constant of metal acetates.