• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.10a
• /
• pp.477-479
• /
• 2017

With the recent advances in medical technology and health care, the prevention and treatment of diseases has developed. Accordingly aging has rapidly progressed. In this life span and aging society, demand for diagnostic centered medical care is increasing rapidly. In this paper, we propose a wearable patient check system based on FPGA that can be controlled by sensors. In the existing hospital, a doctor or nurse visited the patient every hour to check the condition. However, in this paper, patients, doctors and nurses can check the patient's condition at the desired time using patient check system. In addition, the tilt sensor is used for the patient who is uncomfortable to easily control. The proposed FPGA-based hardware architecture consists of an algorithm for enlarged image processing, a TFT-LCD Controller, a CIS Controller, and a Memory Controller to output the patient's status image. Implemented and validated using the DE2-115 test board with Cyclone IV EP4CE115F29C7 FPGA device and its operating frequency is 50MHz.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.14 no.4
• /
• pp.101-107
• /
• 2018

In the stripping scan square wave voltammetry (SV+SWV) polarography that is often used to analyze the concentration of heavy metals in water, we must measure the point where the faradic current that flows by the pure oxidation-reduction reaction at the electrode is greater than the capacitive current, the frequency cannot be too high. Therefore we wanted to find the frequency range that can be measured. In order to do this, we came up with a method to analyze the signal using FPGA Soc. With this method, the frequency of the square wave was increased from 10Hz to 400Hz by 10Hz, and the measuring time of the square wave was changed from 96.695% to 96.765% by 0.005% while 1600 experiments were conducted. As a result, the frequency of the square wave maintained a stable area of potential-current within 320Hz and it was possible to measure the potential-current signal when calculating the measuring time within the frequency range of 96.7155%.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.12
• /
• pp.1554-1563
• /
• 1999

This paper presents the design of high speed processor for a sequence logic control using field programmable gate array(FPGA). The sequence logic controller is widely used for automating a variety of industrial plants. The FPGA designed by VHDL consists of program and data memory interface block, input and output block, instruction fetch and decoder block, register and ALU block, program counter block, debug control block respectively. Dedicated clock inputs in the FPGA were used for high speed execution, and also the program memory was separated from the data memory for high speed execution of the sequence instructions at 40 MHz clock. Therefore it was possible that sequence instructions could be operated at the same time during the instruction fetch cycle. In order to reduce the instruction decoding time and the interface time of the data memory interface, an instruction code size was implemented by 16 bits or 32 bits respectively. And the real time debug operation was implemented for easy debugging the designed processor. This FPGA was synthesized by pASIC 2 SpDE and Synplify-Lite synthesis tool of Quick Logic company. The final simulation for worst cases was successfully performed under a Verilog HDL simulation environment. And the FPGA programmed for an 84 pin PLCC package was applied to sequence control system with inputs and outputs of 256 points. The designed processor for the sequence logic was compared with the control system using the DSP(TM320C32-40MHz) and conventional PLC system. The designed processor for the sequence logic showed good performance.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.3C
• /
• pp.183-189
• /
• 2011

The LMS(Least Mean Square) algorithm is generally used because of tenacity, high mating spots and simplicity of realization. But the LMS algorithm has trade-off between nonuniform collect and EMSE(Excess Mean Square Error). To overcome this weakness, variable step size is used widely but it needs a lot of calculation load. In this paper we consider new algorithm, which can reduce calculations and adapt in case of environment changes, uses original signal and noise signal of IGC(Instantaneous Gain Control). For the real time processing of IGC algorithm, we remove the logarithmic function. The performance of proposed algorithm is tested to adaptive noise canceller in automobile. We show implemented LabVIEW FPGA system of IGC algorithm is more efficient than others.

• Journal of information and communication convergence engineering
• /
• v.13 no.3
• /
• pp.145-151
• /
• 2015

We describe in this paper a hardware-based improvement scheme of a real-time automatic speech recognition (ASR) system with respect to speed by designing a parallel feature extraction algorithm on a Field-Programmable Gate Array (FPGA). A computationally intensive block in the algorithm is identified implemented in hardware logic on the FPGA. One such block is mel-frequency cepstrum coefficient (MFCC) algorithm used for feature extraction process. We demonstrate that the FPGA platform may perform efficient feature extraction computation in the speech recognition system as compared to the generalpurpose CPU including the ARM processor. The Xilinx Zynq-7000 System on Chip (SoC) platform is used for the MFCC implementation. From this implementation described in this paper, we confirmed that the FPGA platform is approximately 500× faster than a sequential CPU implementation and 60× faster than a sequential ARM implementation. We thus verified that a parallelized and optimized MFCC architecture on the FPGA platform may significantly improve the execution time of an ASR system, compared to the CPU and ARM platforms.

• The KIPS Transactions:PartC
• /
• v.16C no.5
• /
• pp.583-588
• /
• 2009

Network intrusion detection system (NIDS) monitors all incoming packets in the network and detects packets that are malicious to internal system. The NIDS should also have ability to update detection rules because new attack patterns are unpredictable. Incorporating FPGAs into the NIDS is one of the best solutions that can provide both high performance and high flexibility comparing with other approaches such as software solutions. In this paper we propose and design a novel approach, prefix sharing parallel pattern matcher, that can not only minimize additional resources but also maximize the processing performance. Experimental results showed that the throughput for 16-bit input is twice larger than for 8-bit input but the used LEs/Char in FPGA increases only 1.07 times.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.12
• /
• pp.1914-1919
• /
• 2021

With the development of advanced industries, research on image processing hardware is essential, and timing verification at the gate level is required for actual chip operation. For FPGA-based verification, DDR3 memory interface was previously applied. But recently, as the FPGA specification has improved, DDR4 memory is used. In this case, when a previously used memory interface is applied, the timing mismatch of signals may occur and thus cannot be used. This is due to the difference in performance between CPU and memory. In this paper, the problem is solved through state optimization of the existing interface system FSM. In this process, data read speed is doubled through AXI Data Width modification. For actual case analysis, ZC706 using DDR3 memory and ZCU106 using DDR4 memory among Xilinx's SoC boards are used.

• The KIPS Transactions:PartA
• /
• v.8A no.4
• /
• pp.479-488
• /
• 2001

As the SoC designs complexity constantly increases, the simulation that uses their software models simply takes too much time. To solve this problem, FPGA-based logic emulators have been developed and commonly used in the industry. However, FPGA-based logic emulators are facing with the problems of which not only very low FPGA resource usage rate due to the very limited number of pins in FPGAs, but also the emulation speed getting slow drastically as the complexity of designs increases. In this paper, we proposed a new innovative emulation architecture and its software that has high FPGA resource usage rate and makes the emulation extremely fast. The proposed emulation system has merits to overcome the FPGA pin limitation by pipelined ring which transfers multiple logic signal through a single physical pin, and it also makes possible to use a high speed system clock through the intelligent ring topology. In this topology, not only all signal transfer channels among EPGAs are totally separated from user logic so that a high speed system clock can be used, but also the depth of combinational paths is kept swallow as much as possible. Both of these are contributed to achieve high speed emulation. For pipelined singnals transfer among FPGAs we adopt a few heuristic scheduling having low computation complexity. Experimental result with a 12 bit microcontroller has shown that high speed emulation possible even with these simple heuristic scheduling algorithms.

• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.3067-3069
• /
• 1999

In this paper, A bit processor for controlling sequence logic was implemented, using a FPGA. This processor consists of program memory interface. I/O interface, parts for instruction fetch and decode, registers, ALU, program counter and etc. This FPGA is able to execute sequence instruction during program fetch cycle, because of divided bus system, program bus and data bus. Also this bit processor has instructions set that 16bit or 32bit fixed width, so instruction decoding time and data memory interface time was reduced. This FPGA was synthesized by pASIC 2 SpDE and Synplify-Lite synthesis tool of Quick Logic company. The final simulation for worst cases was successfully performed under a Verilog HDL simulation environment. And the FPGA programmed for an 84 pin PLCC package. Finally, the benchmark was performed to prove that Our FPGA has better performance than DSP(TMS320C32-40MHz) for the sequence logic control of PLC.

• Journal of Korea Multimedia Society
• /
• v.14 no.3
• /
• pp.368-377
• /
• 2011

This paper explains the hardware structure of SURF(Speeded Up Robust Feature) based feature point extractor and its FPGA verification result. SURF algorithm produces novel scale- and rotation-invariant feature point and descriptor which can be used for object recognition, creation of panorama image, 3D Image restoration. But the feature point extraction processing takes approximately 7,200msec for VGA-resolution in embedded environment using ARM11(667Mhz) processor and 128Mbytes DDR memory, hence its real-time operation is not guaranteed. We analyzed integral image memory access pattern which is a key component of SURF algorithm to reduce memory access and memory usage to operate in c real-time. We assure feature extraction that using a Vertex-5 FPGA gives 60frame/sec of VGA image at 100Mhz.