• 한국결정성장학회지
• /
• 제18권2호
• /
• pp.72-75
• /
• 2008

Zinc oxide (ZnO) thin films were prepared by a sol-gel method. The structural and electrical properties were investigated by varying drying and annealing temperatures. The thin films were coated (250 nm) by spin-coating method on glass substrates. The optimum drying temperature of ZnO thin films was 300$^{\circ}C$ where the resistivity was the lowest and the preferred c-axis orientation was the highest. The annealing was carried out in air and inert atmospheric conditions. The degree of the preferred c-axis orientation was estimated. The highest preferred c-axis orientation was recorded at 600$^{\circ}C$. The preferred c-axis orientation and grain growth resulted in the mobility enhancement of the ZnO thin films, and the lowest resistivity was 0.62${\Omega}{\cdot}cm$ at 600$^{\circ}C$.

• 한국세라믹학회지
• /
• 제33권7호
• /
• pp.802-808
• /
• 1996

PbTiO3 thin films were fabricated onto MgO(100) single crystal substrate by reactive D. C magnetron sput-tering of Pb and Ti metal in an oxygen and argon gas mixture. The annealing of the thin films resulted in the decrease of both the c-axis orientation ratio and the lattice parameter. It is well known that the c-axis lattice parameter of thin film is dependent on the Pb/(Pb+Ti)ratio and the residual stress in the film The PbTiO3 thin films with a Pb/(Pb+T) ratio ranging from 0.45 to 0.57 were fabricated and annealed. The structure of the film the c-axis orientation ratio and the lattice parameter were not dependent on the Pb/(Pb+Ti) ratio before and after annealing. These experimental results proved that the decrease of the c-axis lattice parameter under the annealing conditions was due to the relaxation of the intrinsic stress in the film. This relaxation of the intrinsic stress caused the decrease of the c-axis orientation ratio and this phenomenon can be explained by c-axis growth lattice model.

• 한국세라믹학회지
• /
• 제35권7호
• /
• pp.733-739
• /
• 1998

C-axis oriented zinc oxide thin films were deposited on Cornign 1737 glass substrate by an rf magnetron sputtering technique. The effects of deposition parameters and post heat-treatment on the crystallinity and electical properties of ZnO films were investigaed. As-deposited ZnO films showed the strong c-axis growth and excellent crystallinity under the deposition conditions as follows: substrate temperature 350$^{\circ}C$ ; growth and excellent crystallinity under the deposition conditions as follows ; substrate temperature 350$^{\circ}C$ rf power 75W ; gas pressure 6m Torr; percentage of oxygen 50% The higher heat-treating temperatue was the stronger c-axis growth and the better crystallinity of the deposited ZnO films were. The resistivity of ZnO films was significantly affected by deposition parameters and post heat-treatment. With increasing increased. After post heat-treating at 400$^{\circ}C$ in air the resistivity of ZnO films increased but post heat-treat-ing temperature 500$^{\circ}C$ rather diminished the film resistivity.

• Progress in Superconductivity
• /
• 제2권1호
• /
• pp.15-19
• /
• 2000

[ $YBa_2Cu_3O_{7-\delta}$ ] thin films were deposited by laser ablation using modified melt-textured grown targets. As the laser energy density was increased, the films showed an increasing c-axis orientation and an improvement of superconducting properties. However, at 4 $J/cm^2$, the degree of c-axis alignment and $J_c$ of the film were considerably reduced. These were attributed to the enhanced a-axis outgrowths. It was shown that the increased laser energy density resulted in the formation of $Y_2O_3$ inclusions during the c-axis film growth, and that these inclusions nucleated the a-axis outgrowths.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2000년도 High Temperature Superconductivity Vol.X
• /
• pp.51-55
• /
• 2000

Using modified melt-textured grown targets, YBa$_2$Cu$_3$O$_{7-{\delta}}$ thin films were prepared by pulsed laser deposition technique at the laser energy density from 1 J/cm$_2$ to 4 J/cm$_2$. All the films showed c-axis preferred orientations, however, a-axis outgrowths on the film surface were considerably increased with an increase of the laser energy density. To examine the origin of the a-axis outgrowth formation, the microstructures of films deposited at 2 J/cm$_2$ and 4 J/cm$_2$ were investigated using X-ray diffraction, transmission electron microscopy, and high-resolution electron microscopy. It was shown that a significant number of Y$_2$O$_3$ inclusions were formed during the growth of c-axis oriented films at 4 J/cm$_2$. These inclusions formed nucleation sites for the a-axis outgrowths. It is considered that, due to the unstable growth conditions with a high flux density of incident vapor species and the strain induced by the surrounding c-axis films, the Y$_2$O$_3$ inclusions would prefer the nucleation of α-axis grains.

• ETRI Journal
• /
• 제18권4호
• /
• pp.339-346
• /
• 1997

Good quality a-axis oriented thin films of $YBa_2Cu_3O_{7-x}$ may be grown by the use of a $PrBa_2Cu_3O_{7-x}$ (PBCO) layer as a template. Here we present a detailed study of the nucleation of the PBCO layer, explaining the orientations observed. It is determined that the wavy surface of a $LaSrGaO_4$ (LSGO) (100) substrate consists of the {101} planes by observing cross-sectional transmission electron microscopy images of the interface between the PBCO film and the substrate. The images and selected area diffraction patterns show that a mixed c-and b-axis oriented PBCO layer was initially grown on the substrate, followed by pure b-axis oriented PBCO growth. We explain that the c-axis oriented growth is the result of the growth of the PBCO (019) planes on the LSGO (101) planes. We conclude that the nucleation and growth of the PBCO films at the initial stages depends on the crystallographic plane of the substrate surfaces, however, as the film grows further, the kinetics of the deposition process favors b-axis oriented growth.

• 한국초전도ㆍ저온공학회논문지
• /
• 제19권2호
• /
• pp.9-13
• /
• 2017

This study presents a simple method to control the seed orientation which leads to the various growth characteristics of a single grain REBCO (RE: rare-earth elements) bulk superconductors. Seed orientation was varied systematically from c-axis to a-axis with every 30 degree rotation around b-axis. Orientations of a REBCO single grain was successfully controlled by placing the seed with various angles on the prismatic indent prepared on the surface of REBCO powder compacts. Growth pattern was changed from cubic to rectangular when the seed orientation normal to compact surface was varied from c-axis to a-axis. Macroscopic shape change has been explained by the variation of the wetting angle of un-reacted melt depending on the interface energy between $YBa_2Cu_3O_{7-y}$ (Y123) grain and melt. Higher magnetic levitation force was obtained for the specimen prepared using tilted seed with an angle of 30 degree rotation around b-axis.

• 한국세라믹학회지
• /
• 제35권10호
• /
• pp.1107-1112
• /
• 1998

We could obtan c-axis oriented $SrBi_2$$Ta_2$$O_9$ thin films on usual Pt(111)/Ti/$SiO_2$/Si(100) substrate using a r. f. magnetron sputtering technique. According to the increase of sputtering pressure from 250 to 300 mTorr the Bi content and degree of the c-a xis preferred orientation of $SrBi_2$$Ta_2$$O_9$ thin films were increased. By controlling Bi(or $Bi_2O_3$) loss from $SrBi_2$$Ta_2$$O_9$ thin films during post annealing and by inserting $Bi_2O_3$ layer in $SrBi_2$$Ta_2$$O_9$ thin films the effect of Bi content on the c-axis oriented growth of $SrBi_2$$Ta_2$$O_9$ thin films could be investigated without the effect of sputtering pressure. The degree of the c-axis preferred orientation of $SrBi_2$$Ta_2$$O_9$ thin films was increased with increasing with increasing Bi content by control of Bi(or $Bi_2O_3$) loss of $SrBi_2$$Ta_2$$O_9$ thin films. But the c-axis oriented growth of $SrBi_2$$Ta_2$$O_9$ thin films disappeared by the inserting of $Bi_2O_3$ lay-er in $SrBi_2$$Ta_2$$O_9$ thin films.

• 한국초전도ㆍ저온공학회논문지
• /
• 제6권3호
• /
• pp.21-26
• /
• 2004

Deposition condition of YBa$_2$Cu$_3$$O_{7-x}$ (YBCO) films on moving IBAD templates (CeO$_2$/IBAD-YSZ/SS) was studied in a hot-wall type metal organic chemical vapor deposition (MOCVD) process using single liquid source. The reel velocity was 40 cm/hr and the source mole ratios of Y(tmhd)$_3$:Ba(tmhd)$_2$:Cu(tmhd)$_2$ were 1:2.3:3.1 and 1:2.1:2,9, Two different types of IBAD templates with thin CeO$_2$ and thick CeO$_2$ layers were used, The YBCO films were successfully deposited at the deposition temperatures of 780~89$0^{\circ}C$ ; the a-axis growth was observed together with the c-axis growth up to 83$0^{\circ}C$. while the c-axis growth became dominant above 83$0^{\circ}C$. The top surface of the c-axis film was fairly dense and included a small amount of the a-axis growth, although the peaks of the a-axis grains were not observed in XRD pattern, The YBCO film deposited on IBAD template with thin CeO$_2$ layer showed low critical current of 2.5 A/cm-width. while the YBCO film deposited on IBAD template with thick CeO$_2$ layer showed higher critical current of 50 A/cm-width. This result indicates that thick CeO$_2$ layer is thermally more stable than thin CeO$_2$ layer at the high deposition temperature of the MOCVD process.s.

• Journal of information and communication convergence engineering
• /
• 제3권3호
• /
• pp.131-136
• /
• 2005

The effects of the deposition temperature on the growth characteristics of the ZnO films were studied for film bulk acoustic wave resonator (FBAR) device applications. All films were deposited using a radio frequency (RF) magnetron sputtering technique. It was found that the growth characteristics of the ZnO films have a strong dependence on the deposition temperature from 25 to $350^{\circ}C$. The ZnO films deposited below $200^{\circ}C$ exhibited reasonably good columnar grain structures with a highly preferred c-axis orientation while those above 200°C showed very poor columnar grain structures with a mixed-axis orientation. This study seems very useful for the future FBAR device applications.