• Progress in Superconductivity
• /
• v.4 no.1
• /
• pp.94-98
• /
• 2002

Two kinds of multifilament Bi-2223／Ag tapes, which are different in the precursor calcination temperatures, were heat treated for different time (12, 20, 30, 50, 70, or 100 h) firstly to obtain varied B2223 contents, and then followed by the same pressing and sintering cycles. The relation of the 2223 phase contents after the first sintering and the transport property of the fully processed tapes was studied. The results show that 75-80% 2223 phase formed in tapes before the first cold pressing is beneficial to get a high $I_{c}$ in the final tapes. Compensating the total heat treatment time of the tapes first sintered for 20 h to the same length as that first sintered for 50 h in the subsequent sintering stages, different $I_{c}$ enhancements were observed in these two tapes. No improvement on $I_{c}$ was found in the tape made from the powder calcined at higher temperature, whereas for the tape prepared with the lower temperature calcined powder, the $I_{c}$ was increased to the same level as that first sintered for 50 h. The 2223 contents before the intermediate mechanical work is related to the residual reactants, especially to the liquid phase, which is of vital importance to the phase conversion and healing microcracks, meanwhile, to the size and distribution of the non-superconducting secondary phases. The lower temperature calcined powder resulted in slow formation of 2223 phase, but also provided more reactants and liquid phase for the further phase conversion, as a consequence, for the Improvement of $I_{c}$. c/.

• Analytical Science and Technology
• /
• v.5 no.4
• /
• pp.389-399
• /
• 1992

Liquid Chromatographic behavior of Pd(II) in Isonitrosoethylacetoacetate lmine, $Pd(IEAA-NR)_2$ (R=H, $CH_3$, $C_2H_5$, $n-C_3H_7$, $C_6H_5-CH_2$, $n-C_4H_9$) chelates were investigated by reversed-phase HPLC on Micropak MCH-5 column using methanol/water as mobile phase. The optimum conditions for the separation of $Pd(IEAA-NR)_2$ chelates were examined with respect to the effect of the flow rate, sample solvent, mobile phase strength and column temperature. It wass found that metal chelates were properly eluted in an acceptable range of capacity factor value($0{\leq}log\;k^{\prime}{\leq}1$). The dependence of the logarithm of capacity factor(k') on the volume fraction of water in the binary mobile phase was examined. Also, the dependence of k' on the liquid-liquid extration distribution ratio($D_c$) in methanol-water/n-alkane extration system was investigated. Both kinds of dependence are linear, which susggests that the retention of the electroneutral metal chelate is largely due to the solvophobic effect. Standard adsorption enthalpy changes (${\Delta}H^{\circ}$) and standard adsorption entropy changes (${\Delta}S^{\circ}$) of Pd(II) Isonitrosoethylacetoacetate imine chelates on Micropak MCH-5 column were calculated by measuring capacity factor with changing temperature of the column.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.87-88
• /
• 2006

The phase transformation behaviors of Ni-Ti shape memory alloys were investigated through a DSC(Differential Scanning Calorimetry). The annealing temperatures were applied from $600^{\circ}C,\;700^{\circ}C,\;800^{\circ}C,\;and\;900^{\circ}C$ for their effects on the phase transformation behaviors. Based on the results of DSC, phase transformation behaviors of shape memory alloys can be predicted by Liang's phase transformation model or Tanaka's phase transformation model.

• The Korean Journal of Ceramics
• /
• v.3 no.3
• /
• pp.187-190
• /
• 1997

The aluminum-magnesium (Al-Mg) aklloys have been proved to be an effective solvent for synthesis of cubic-phase boron nitride (cBN) from hexagonal-phase boron nitride (hBN) at the conditions of high pressures and high temperatures (HP/HT). Various kinds of hBN powders having different crystallinity have been tested for cBN synthesis with Al-Mg solvents. The conversion ratio from hBN to cBN and the shape of synthesized cBN crystals appeared to be affected strongly by chemical composition and added amount of Al-Mg solvents as well as crystallinity of BN powders. As the magnesium content increased in the Al-Mg solvents, the conversion ratio increased and the size of cBN crystals became larger. The crystal facets developed well in the specimens with solvents having high Mg content. It was observed that a hBNlongrightarrowcBN transformation occurred more easily in the specimens having well crystallized hBN powders. Amorphous BN having much $B_2O_3$ impurity exhibited a low threshold temperature for transformation to cBN, which was attributed to crystallization of amorphous BN to well crystallized hBN prior to transformation into cBN with help of $B_2O_3$.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.1
• /
• pp.25-30
• /
• 2000

The relation between the phase-shift profile for the intermediate frequencies and the Langmuir adsorption isotherm at the poly-$Pt/0.1\;M\;H_2SO_4$ aqueous electrolyte interface has been studied using ac impedance measurements, i.e., the phase-shift methods. The suggested interfacial equivalent circuit consists of the serial connection of the electrolyte resistance ($R_S$), the faradaic resistance $(R_F)$ and the equivalent circuit element $(C_P)$ of the adsorption pseudocapacitance $(C_\varphi)$. The delayed phase shift $(\varphi)$ depends on both the cathode potential (E) and frequency (f), and is given by $\varphi=-tan^{-1}[1/2{\pi}f(R_s+R_F)C_p]$. The phase-shift profile $(\varphi\;vs.\;E)$ for the intermediate frequency (ca. 6Hz) can be used as an experimental method to determine the Langmuir adsorption isotherm (9 vs. E). The equilibrium constant (K) for H adsorption and the standard free energy $({\Delta}G_{ads})$ of H adsorption at the poly-$Pt/0.1\;M\;H_2SO_4$ electrolyte interface are $1.8\times10^{-4}\;and\;21.4kJ/mol$, respectively. The H adsorption is attributed to the over-potentially deposited hydrogen (OPD H).

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.6 no.3
• /
• pp.182-192
• /
• 1994

This paper focuses on the investigation of the heat transfer phenomena that occur inside the cylindrical tube. The inclination of the tube is adopted as a principal parameter varying from vertical to horizontal. The phase change material employed in this experiment is 99 percent pure n-docosane paraffin($C_{22}$ $H_{46}$). It is found that the amount of solidified mass during a prescribed solidifying period is not sensitive to the inclination of the tube but to the local layer thickness. It is studied that the latent energy is the largest contributor to the total extracted energy. The sensible energy($E_{s1}$, $E_{s2}$, $E_{s3}$) may not be negligible at the large wall-subcooling and initial-liquid-superheating, also at the first step of solidifying.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04a
• /
• pp.17-20
• /
• 2002

The effects of relatively low lead content (0.2~0.3) on the 2223 phase formation and transport property of Bi-2223/Ag tapes have been investigated. The results show that lead contents have great impact on the phase assemblage of precursors, subsequently, on the phase formation and transport property of silver sheathed BSCCO-2223 tapes. Powders containing Pb=0.25 and Pb=0.3 resulted in the nearly identical $J_c$ values in fully processed tapes, but leaded to significant difference on the phase formation process. For the case of Pb=0.2, both low conversion fraction of 2212 to 2223 and low $J_c$ value were obtained in final reacted tape, which was probably due to lack of enough liquid phase to facilitate the phase transformation.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.2
• /
• pp.109-114
• /
• 2000

The relation between the phase-shift profile fur the intermediate frequencies and the Langmuir adsorption isotherm at the poly-Ir/0.1 M $H_2SO_4$ aqueous electrolyte interface has been studied using ac impedance measurements, i.e., the phase-shift methods. The simplified interfacial equivalent circuit consists of the serial connection of the electrolyte resistance $(R_s)$, the faradaic resistance $(R_F)$, and the equivalent circuit element $(C_P)$ of the adsorption pseudoca-pacitance $(C_\phi)$. The comparison of the change rates of the $\Delta(-\phi)/{\Delta}E\;and\;\Delta{\theta}/{\Delta}E$ are represented. The delayed phase shift $(\phi)$ depends on both the cathode potential (E) and frequency (f), and is given by $\phi=tan^{-1}[1/2{\pi}f(R_s+R_F)C_P]$. The phase-shift profile $(-\phi\;vs.\;E)$ for the intermediate frequency (ca. 1 Hz) can be used as an experimental method to determine the Langmuir adsorption isotherm $(\theta\;vs.\;E)$. The equilibrium constant (K) for H adsorption and the standard free energy $({\Delta}G_{ads})$ of H adsorption at the poly-Ir/0.1 M $H_2SO_4$ electrolyte interface are $2.0\times10^{-4}$ and 21.1kJ/mol, respectively. The H adsorption is attributed to the over-potentially deposited hydrogen (OPD H).

• The Korean Journal of Zoology
• /
• v.37 no.3
• /
• pp.318-323
• /
• 1994

The association of replication origins/termini with nuclear matrix during S phase was investigated by DNase digestion of halo structures in synchronized mouse LPI-1 cells. The binding of parental DNA to nuclear matrix was constant throughout S phase. When nuclear matrix was isolated from the cells pulse-labeled with 3H-thvmidine at various stases of S phase, total 3H-labels associated with nuclear matrix were specifically higher at So, Sa and Ss stages than other stases of S phase, suggesting that the newly synthesized DNAs at those stages are not excluded out of nuclear matrix. Similar patterns were obsenred from the pulse-chase experiments, in which cells were pulse-labeled at each stage of S phase and further incubated for 1 hr. These results suggest that the replication origins and termini are fixed at the nuclear matrix, and that the nuclear matrix binding fractions of DNA at 3C-pause may contain a large population of replication origins and termination sites.

• Proceedings of the KIPE Conference
• /
• 2004.11a
• /
• pp.96-100
• /
• 2004

This paper deals with power quality disturbance generator with phase jump function. The proposed generator can be applied to the performance test of custom power devices. Voltage sag, swell, outage, unbalance and phase jump after outage are provided by the generator. The phase jump operating principle of the generator is described and analysed. The control scheme of the disturbance generator is simple and hardware setup is cost effective compared with the conventional scheme. The usefulness of the generator is verified through simulation and experimental results.