• Journal of Power Electronics
• /
• v.18 no.2
• /
• pp.375-382
• /
• 2018

A novel active controlled primary current cutting-off zero-voltage and zero-current switching (ZVZCS) PWM three-level dc-dc converter (TLC) is proposed in this paper. The proposed converter has some attractive advantages. The OFF voltage on the primary switches is only Vin/2 due to the series connected structure. The leading-leg switches can obtain zero-voltage switching (ZVS), and the lagging-leg switches can achieve zero-current switching (ZCS) in a wide load range. Two MOSFETs, referred to as cutting-off MOSFETs, with an ultra-low on-state resistance are used as active controlled primary current cutting-off components, and the added conduction loss can be neglected. The added MOSFETs are switched ON and OFF with ZCS that is irrelevant to the load current. Thus, the auxiliary switching loss can be significantly minimized. In addition, these MOSFETs are not series connected in the circuit loop of the dc input bus bar and the primary switches, which results in a low parasitic inductance. The operation principle and some relevant analyses are provided, and a 6-kW laboratory prototype is built to verify the proposed converter.

• Journal of Convergence for Information Technology
• /
• v.10 no.5
• /
• pp.111-116
• /
• 2020

Recently, many safety accidents involving children shuttle buses take place. Without a teacher for help, a safety accident occurs when the driver can't see a child who is getting off in the blind spot of both frontside and backside. A deep learning-based smart mirror allows user authentication and provides various services. Especially, It can be a role of helper for children, and prevent accidents that can occur when drivers or assistant teachers do not see them. User authentication is carried out with children's face registered in advance. Safety accidents can be prevented by an approximate sensor and a camera in frontside and backside of the bus. This study suggests a way of checking out whether children are missed in the process of getting in and out of the bus, designs a system that reduce blind spots in the front and back of the vehicle, and builds a safety system that provide various services using GPS.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2006.05a
• /
• pp.399-402
• /
• 2006

This paper presents a new circuit topology of dc bus line switch-assisted half-bridge soft switching PWM inverter type dc-dc converter for arc welder. The proposed power converter is composed of typical voltage source half-bridge high frequency PWM inverter with a high frequency transformer link in addition to dc bus line side power semiconductor switching devices fer PWM control scheme and capacitive lossless snubbers. All the active power switches in the half-bridge arm and dc bus lines can achieve ZCS turn-on and ZVS turn-off commutation operation and consequently the total turn-off switching losses can be significantly reduced. As a result, a high switching frequency of using IGBTs can be actually selected more than about 20 kHz. The effectiveness of this new converter topology is proved for low voltage and large current dc-dc power supplies such as arc welder from a practical point of view.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.4
• /
• pp.24-31
• /
• 2007

Up to date, a lot of bus protocol and bus architecture are released though most of them are based on the shared bus architecture and inherit the limitation of performance. SNP (SoC Network Protocol), and hence, SNA (SoC Network Architecture) which are high performance on-chip-bus protocol and architecture, respectively, have been proposed to solve the problems of the conventional shared bus. We refine the SNA specification and improve the performance and functionality. The performance of the SNA is improved by supporting simultaneous routing for bus request of multiple masters. The internal routing logic is also improved so that the gate count is decreased. The proposed SNA employs XSNP (extended SNP) that supports almost perfect compatibility with AMBA AHB protocol without performance degradation. The hardware complexity of the improved SNA is not increased much by optimizing the current routing logic. The improved SNA works for IPs with the original SNP at its best performance. In addition, it can also replace the AMBA AHB or interconnect matrix of a system, and it guarantees simultaneous multiple channels. That is, the existing AMBA system can show much improved performance by replacing the AHB or the interconnect matrix with the SNA. Thanks to the small number of interconnection wires, the SNA can be used for the off-chip bus system, too. We verify the performance and function of the proposed SNA and XSNP simulation and emulation.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1527-1536
• /
• 2014

This paper investigates the optimal values of turn-on and turn-off angles, and ratio of flux linkage at turn-off angle and peak phase current positions of optimal control for accomplishing maximum output power in an 8/6 Switched Reluctance Generator (8/6 SRG). Phase current waveform is analyzed to determine optimal excitation angles (optimal turn-on and turn-off angles) of the SRG for maximum output power which is applied from a nonlinear magnetization curve in terms of control variables (dc bus voltage, shaft speed, and excitation angles). The optimal excitation angles in single pulse mode of operation are proposed via the analytical model. Simulated and experimental results have verified the accuracy of the analytical model.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.39 no.6
• /
• pp.833-839
• /
• 2019

Bus Information System (BIS) collects information related to the operation of buses and provides information to users through predictive algorithms. Method of predicting through recent information in same section reflects the traffic situation of the section, but cannot reflect the characteristics of the target line. The method of predicting the historical data at the same time zone is limited in forecasting peak time with high volatility of traffic flow. Therefore, we developed a pattern recognition bus arrival time prediction algorithm which could be overcome previous limitation. This method recognize the traffic pattern of target flow and select the most similar past traffic pattern. The results of this study were compared with the BIS arrival forecast information history of Seoul. RMSE of travel time between estimated and observed was approximately 35 seconds (40 seconds in BIS) at the off-peak time and 40 seconds (60 seconds in BIS) at the peak time. This means that there is data that can represent the current traffic situation in other time zones except for the same past time zone.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.1D
• /
• pp.23-31
• /
• 2012

Busan Metropolitan City government has been implementing the local Bus Quasi-Public Operating policy since 2007. As a result of the policy, financial burden to cover financial deficit has become a big social issue. For successful settlement of the policy, the government should be able to gradually cut off the financial support for the deficit by continuously increasing the bus demand, which can be accomplished by providing more convenient bus services. The weather conditions that affect the public transportation demand include rain, fog and snow. They affect the mode choice for public transportation use, which in turn results in decrease in bus demand. In short, the adverse weather conditions result in significant profit loss of bus transportation, and consequently it financially burdens the City of Busan. In this research, the pattern of travelers' use of transportation modes given various weather conditions was analyzed. In addition, the reasons why people transfer from one to other transportation modes were analyzed by conducting a field survey, and policy implications on desirable public transportation facilities and transfer system were discussed.

• The Journal of Korean society of community based occupational therapy
• /
• v.1 no.1
• /
• pp.7-17
• /
• 2011

Objective : This study aimed to understand the experience of taking a bus, investigate successful strategies to overcome the psychological difficulties of people with disabilities. Method : In this study, a phenomenological and hermeneutic approach was used to gain a deeper understanding of the behavior, the language, the process. For participants through interviews and participant observation data were collected. Phenomenological interpretation of the way through technology and to evaluate the results. Result : Ambulatory persons with disabilities in the community have confidence in the bus-independent movement in the community possible. And get on and off the bus at the moment of urgent strategies to use in the bus seats were taken. To cope with unexpected situations like that do not put stress was confirmed. In addition, by bus and go sit on the seat to look at the patient's burden was to. Conclusion : Ambulant disabled people's confidence in the bus had a significant impact on the independent movement. Always on the lookout for falling, and many psychological difficulties and to overcome unforeseen circumstances to predict and know that public transportation could be.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.5
• /
• pp.374-380
• /
• 2011

In this paper a printing process for patterning electrodes on large area substrate was developed by combining screen printing with reverse off-set printing. Ag ink was uniformly coated by screen printing. And then etching resist (ER) was patterned in the Ag film by reverse off-set printing, and then the non-desired Ag film was etched off by etchant. Finally, the ER was stripped-off to obtain the final Ag patterns. We extracted the suitable conditions of reverse Using the process we successfully fabricated gate electrodes and scan bus lines of OTFT-backplane used for e-paper, in which the diagonal size was 6 inch, the resolution $320{\times}240$, the minimum line width 30 um, and sheet resistance 1 ${\Omega}/{\Box}$.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.12
• /
• pp.2184-2188
• /
• 2007

We developed a novel method of partial discharge(PD) location based on the fact that the waveform of PD signal propagate along the GIB (Gas Insulated Bus) is composed of several modes of electromagnetic wave with different group velocities and cut-off frequencies. From the PD waveform, measured at a broadband PD sensor attached on the GIB, we could derive arrival time and frequency components of different modes using the short term Fourier transform or etc. After the group velocities of different modes are calculated, the location of the PD source could be estimated. To show the effectiveness of this new locating method in a real on site application, we used this method to locate the position of a PD source at a 76 m long 345 kV GIB substation. The estimated location of the PD source using the method proposed above was in good agreement with the actual location found from the inspection result of internal component in the GIB with 2.4% of the estimation error.